Bufferbloat Fix For Gaming!!! (Rate Limit Method)

[@JohnGlasscock]

rOSES ARE RED Violets are blue I was first and so are u

[@jokerbaby21_]

Glasscock I was first not u

[@snisnisnusni6fidjsij665]

Glasscock hey did you add me I freind requested you on xbox and sent you a message that said shazam

[@snisnisnusni6fidjsij665]

_ AC _ Andrew _ nope haha

[@jokerbaby21_]

SHAZAM 127 Wdym

[@JohnGlasscock]

I will check the next time I get on Xbox

[@ahmedsalah7474]

You saved me man, limited my upload bandwidth and everything is fine now. thank you!

[@laeioun]

A truck weighs a total of 30T carrying a 20T load, so the truck itself weighs 10T. Let's say you know the truck needs to cross a bridge that has a weight limit of 20T. You would ideally calculate the overhead and the required number of trucks to split the load between beforehand. Two trucks can split a 20T load and both weigh equal to the weight limit whereas a single truck carrying the same load weighs 10T over the limit. The weight overhead of each truck is analogous to packet overhead. The traffic shaper protocols most routers use at the moment do not include packet overhead in their calculations and actually don't even allow you to configure them to do so. These protocols are meant to reduce noticeable bufferbloat by prioritising real-time data (like online games and video streams, for example) but this does not work during high traffic periods if overhead is not calculated. So, in our analogy, the trucks try to cross but end up stuck and need to be dismantled at the half-way point. This is bufferbloat. Bandwidth limiting works by lowering the size limit of each packet so that large packets are always broken down into two before they are carried across. If all packets are smaller than the limit, they all go through immediately and bufferbloat will not occur. It's basically lowering the weight limit by 10T to correct for missing out the overhead in the calculation. Now the advertised weight limit is 10T (even though the real weight limit is 20T), so the protocol sees the load is 20T and splits it over two trucks as is ideal.

[@gitoffmylawn3887]

Why wouldn't you just use the r7000 for QOS.? Does the switch give a better result?

[@BenjaminCronce]

Many generic forms of QoS do not work well around 1Mb/s. This is an issue between the serialization delay relative to the average bandwidth. As a general rule of thumb, my bufferbloat is about 0ms. Most of the time dslreport showss my bloat about 1-5ms, but if I actually run a ping against an external server, with no QoS to prioritize the ping, I see the exact same ping during the entire test. There is a limit in precision the test can do since it is using both TCP and your browser. The best forms of turn-key easy QoS are codel, fq_codel, red, and fq_red. The "fq" versions are better. Both red and codel are virtually the same, but red is ASIC friendly. Just set your bandwidth and you're done. These also have issues around the 1Mb mark and both recommend at least 10Mb for the best debloating experience. Below 1Mb, they may require manual tweaking otherwise they can cause excessive packet loss.

[@supernice_auto]

Do you think bufferbloat is necessary for gaming if the PC is the only device on the network and/or the network has very little activity? I'm on a 1 gig fiber connection and need to play competitively just not sure if introducing sqm on my openwrt Linksys can somehow make things worse from a latency/response time perspective.

[@Steve-ph7qn]

If your modem is layer 3, which it is as it has a DHCP server running on it - you are 100% using it for routing @ 4:15. Source: I work in networking with actual kit(not netgear). Routing in networking is the network to network connection, IE. from your private network, to your ISP's network in which your router has an IP address, and then the internet, which is just a load of networks connected together. That switch you have is just using forwarding/MAC table to send traffic to one specific device interface. There is NO routing as this is all layer 2.

[@CUBAMUSICA84]

Just set game ports or "service port" to highest priority and set port 80 and port 443 to lowest your router will do the rest. If you are using bandwidth percentages use 67% for highest and 33% for normal. I would avoid settings for "medium" priority I think this just makes your router not sure of what it's doing. Hope this helps please give me a like if it does.

[@parallax8207]

your channel is amazing. All the information is true and scientifically proven!

[@cyberwolfe]

I'm in LOVE with your last name... it's so badass! :)

[@JohnGlasscock]

Thank you

[@jjhassy]

@@JohnGlasscock np

[@whereisthedollar]

Okay, so I took your advice. Ordered the switch. Like you, my ISP does not allow any QOS on their combo. I have no addition router. I always use an Ethernet cable when gaming, but the buffer float ping was inconsistent and particularly high on the up side. After much trail an error with the switch/ DSL reports, I made adjustments with the switch from the ISP. Today, was the most successful day gaming with no noticeable buffer float affecting play. Only time will tell if this works for me in the long run, but I wanted to say” Thank You “for this tip.

[@anotherstupidfeature]

If Window Receive Autotuning is causing bufferbloat, SQM most likely doesn't help. If I set autotuning level to [normal], bufferbloat is 50 to 170 ms. If I set it [restricted], [highlyrestricted] or [disabled], bufferbloat drops to 0-10 ms but at the same time the internet speed drops from 900+/50 to 30-200/20-40 mbits. So is there anything to fix bufferbloat causing by Windows autotuning?

[@Geostationary0rbit]

is there a way of figuring out your rate limit from how much bufferbloat you are getting?

[@snickeas1]

Good video. I had noticed the dark theme buttom on their website until watching this.....Kudos to you!

[@JohnGlasscock]

Thank you!!

[@eliii6667]

Do you have DHCP enabled on the switch as well as the ATT router ? or do you turn off one of them

[@NvaderRetro]

man i nearly switched from ATT because of this. I'm going to pick up one of these switches and give this a try. Which is cheaper than investing in a new router for a cable connection. Thanks

[@MinecraftChannelPVP]

Any Fritzbox Tweaks? like i have Fritzbox 7530 maybe can someone help me there?

[@FreakyLawnmower]

Glasscock the netduma forum people always say those bufferbloats test are inconsistent and not accurate.

[@JohnGlasscock]

It's not precise but it's a decent means of measurement. Nothing is going to be absolutely precise. Even Ookla speed test is not accurate, that is why they offer a desktop app for better accuracy. It's a web service designed to take sample measurements. Maybe Netduma should design a an app built into duma OS for taking more precise measurements. I would pay for that

[@xXegox]

voipreview.org/speedtest offers are more accurate speedtest/bufferbloattest but i guess its still not the best.

[@BenjaminCronce]

@@xXegox That service can't even handle my upload. Maxes out around 130Mb/s. Also misreports my download bandwidth as being about 8% higher than what my router and OS are claiming. Also questionable what it actually considers as "bufferbloat" because it claims my bloat is exactly the same as my ping. I typically measure 0ms bloat myself.

[@BenjaminCronce]

An inherent issue with using TCP and a browser. It's very close to correct. It may have some odd interactions with certain networks that I am not familiar with, but it's generally within 20% of what I manually measure.

[@a1boston73]

xXegox is this new? Im going to try this website, thanks

[@davewasem3242]

Do you know why it does not give me a grade for bufferbloat? All I get is a grey circle with a day inside. On the test, it never went above 18. Weird?

[@diegootterburg4781]

I bought the s8000 I applied the in rate limit I have 10 megas for internet but it doesn't fix the buffer low cloud you help me please

[@CountZakula]

Does this only work with upload and I'm guessing my ISP is in charge of my download?

[@alexanderlopez4518]

Hey John, I ordered a Netgear Nighthawk Pro XR500 & on your vid you said that you couldn't "change" the default router that AT&T gave you. How do you shut off your WiFi capabilities? Cause I don't know if I'm gonna have the same problem you have.

[@alexanderlopez4518]

BTW should I get a switch just in case?

[@teddythodo3302]

Is this significantly better than QoS ? Once I QoS’d my new netgear router I noticed incredible difference. Will the s8000 really make a bigger difference?

[@Zenixgaming_Tv]

If I have a my own modem and router setup would a 1gig switch still be beneficial or no any help would be greatly appreciated by myself

[@jasonmorgan7807]

I just got a switch for my 1gig connect 50 upload , virgin Router moder still using WiFi and KZbin and social media buffers or slow loads ,should I use the hub as just a modem and use the Netgear nighthawk for the wifi

[@Draghoned]

Excellent video ... one question, in a 100MBytes download connection ... would the "in rate limit" values ​​be the same? 128Mbits ... and could this procedure be carried out only from the network and services configuration of the pc? no need for a switch? ... thanks for your help congratulations

[@Fuzzylumpkins02]

Howcome the first test you did on dslreports you had 32 streams on download and upload but on second test you has 32 and 16 streams. So from what u can tell you lowered you stream to 16 to reduce the buffer bloat. Can you try the same test again with 32 and 32 after your setting changes in your switch?

[@PescaitoFrito]

I'm guessing this buffer bloat reduction only work with router that have specific QOS to actually mitigate the traffic? Cause at least on my on old router: TL-WR720N

[@muimuhadresh3986]

What are my options to reduce bufferload, when there are no limiting settings available?

[@PS3xDesTiinY]

It is possible to use qos and set a rate limit? Or use both isnt that good?

[@SkepticMind1939]

@John Glasscock TPLINK routers are now coming only with QOS, they removed bandwith control. Do you know if it is as effective? Because the tests I ran were not succesful in reducing bufferbloat with QOS.

[@junewood9215]

Hi glasscock, can I do this with the tp link w9970, thx bro.

[@jacedragon]

so with this type of setup. is the switch controlling everything or your modem since its a router as well? im in a situation where i found out cat5e is running in the home to 5 rooms. but cant only access from the basement. so if i go modem-router-switch. it would be a waste of use of the router being in a basement.. this set up would be perfect as the switch is connected after the modem and the router used as AP .

[@Gimpzorgaming]

What do you recommend now that this switch is no longer available? I have a shitty two in one modem/router combo from my isp that I can't baseline because of MOCA. I have severe bufferbloat issues, and something like this would have worked wonders. Unfortunately you can't find them anywhere anymore.

[@vindumztv8763]

Hi sir just want to ask do u have an idea why i'm not getting the right speed from my internet service provider? Do yoU have tricks or settings on the router (RAX45)? Why is it happening? My ISP always says its ok on their end (direct connection from modem to laptop) but from router to laptop not even half of my subscribed speed. Please help me understand. Thanks.

[@djaran13]

Great info. Quick question. Since I have the xr500 for the duma OS. If I use the setup you are using with the switch. I wont be able to use the Geo Filter. I have the same gateway and speeds you have with at&t gigapower. I hate having to play COD with overseas peer to peer players so I need the Geo Filter. But with that switch I will lose being able to stay on dedicated servers in NY and GA

[@jasonmorgan7807]

do all devices get a ip address , seen tech guy saying only put a switch after router because isp only gives 1 ip pool

[@Udiie_-x]

This vídeo save my gameplay thanks, Hello from Brasil 👍

[@steelautomated]

You mentioned AT&T won’t let you use a VPN? They should not block a vpn service. Why don’t you use the dmz plus mode on your AT&T gateway? This would allow you to use the router of your choice. Thanks for the video!

[@JohnGlasscock]

I appreciate it! Well, to start off the DMZ plus zone on the gateway still routes traffic through the gateway even though if your 3rd party router is receiving a public IP through DMZ plus. What ends up happening is my throughput gets cut in nearly half and instead of getting 1000mbps I end up with like 300mbps at the max. Secondly I have no use for a VPN

[@steelautomated]

That is good to know, my speeds do not come close. I am curious if it can cause performance issues on any scale. For example ping, reliability, etc. Thanks

[@JohnGlasscock]

@@steelautomated from my experience I have had performance issues when placing a 3rd party router in the DMZ. Like I mentioned with the throughput being cut in more than half

[@Aladdin-Alewi]

Hi John, you have no idea how much I would like to thank you! Your solution eliminated totally the bufferbloat. One question! On my laptop, whenever I do the dslreport test, I got A+ for all results, but on my ps4 pro the results are bad! I have no explanation for that. Is there anything I can do? Thanks in advance.

[@kayonex-2461]

That's because the PS4 browser has not got enough power to provide reliable measurements on DSLReports.com

[@Dawgsrlife]

Hello, I have the following problem: Action doesn't save the video file when recording, obs records a black screen, windows xbox recorder fails to record, and e.tc. for other recording applications or softwares To summarize, I cannot record at all on my new laptop... Noone else had experienced this problem before, as that I had no results spending hours on the internet trying to find a solution My CPU is Intel Core i5 7300HQ My GPU is Nvidia GeForce GTX 1050TI I've updated all my drivers successfully and no changes, and I've tried recording using both CPU, GPU, and even without hardware acceleration. My only option is to do a factory reset (which I don't want to do at the moment), butI'm not on the urge to record videos just yet; but I'd really like to share my gaming experiences on my laptop (Dell Inspiron 15 7567) If anyone has any clues or knows a fix to this, I'd greatly appreciate some help to this. Thank you!

[@cod_makes_me_cum4724]

hey glasscock , without enabling the qos , i still get A grade in bufferbloat , is it normal? or i still need to do that?

[@frank1144]

of course, it's normal cum 47.

[@its_beo]

If i were to set up a qos for my ps4 and open some important ports. Will that stop lag and allow me to have most bandwidth? I'm asking because I plan to stream games without laging. I have a r7000 netgear router and that modem you where talking about in your best modem for gaming video.

[@its_beo]

Btw also I'm asking because I have two step brothers that use ALOT OF bandwidth

[@JohnGlasscock]

Yeah as long as you prioritize by device, not services

[@its_beo]

@@JohnGlasscock ok thank you

[@Delttyy]

Been having bad buffer bloat and also packet burst, so picked up this switch in hopes to fix it.

[@kanoooo1111]

Did you use link aggregation before connecting to s8000 ?

[@garethwigglesworth8187]

I was about to buy a ubiquiti edgerouter to sort this. Thanks. I have an s8000

[@fraudulentearth5117]

Wait, you can do a bufferbloat test on PS4, ow exactly?

[@toomuchstarbucks6787]

I assume he uses the PS4 web browser.

[@rm6412]

I’ve tried this and Ive gotten a message that PS4 browser gives no upload progress ¯\_(ツ)_/¯

[@Hotdogbunker]

will this even work with a puma 6/7 modems?

[@l7nalmari189]

Did you make a video for xr500 setup QOS??

[@garethwigglesworth8187]

Same method for xbox as your razorblade pro?

[@smac1943]

hi John I get an error when I do the speed test, it says instant download speed has dropped far below the running average, I have no idea what this means, I was curious if you have come across this?

[@shaq3199]

If I have a xr 1000 do I still need this switch?

[@meppie1922]

Nice video man. I use the Netgear GS 105 Ev2. I think it does the same as the Netgear S8000 doesn't it?

[@StarcraftSwarm]

Should I limit my upload speed if during the upload test I get a 300 ms spike for like 1 second and then it stays at 0-5 and i get an overall A/A+ bufferbloat rating? Or is it supposed to be stable 0-5 ms with no spikes whatsoever? Also while pinging google.com and running a speed test my ping to google is very stable with no spikes , whereas before changing my router during the upload test my ping to google would reach 500-600 ms. Perhaps the better router fixed my issue without needing to limit my bandwidth?

[@ДмитрийКнязев-э1ф]

Чувак, спасибо тебе, только вчера узнал о таком буфере. Оборудование не такое как у тебя, но общую пропускную способность удалось урезать и получить ААА

[@Steven-pe2mg]

Hello, does upload speed matters in gaming ( black ops 3)? My upload speed is between 5-10 with cable. I have a router/modem.

[@JohnGlasscock]

Between 5 and 10 is fine

[@Josuebrbs]

I had 15mbs download and 2 upload and i did fine on cod

[@Steven-pe2mg]

Ok, I have a netgear s8000 switch, you can put the switch in game mode... will it give you advance over download and upload?

[@Steven-pe2mg]

Oké!

[@highconsciousness7563]

At least 4 up will do.

[@jessecampbell562]

john glasscock when i go to dslreport and do the test my results wont load its just the 3 blue cirlcles loading i tried on all my browers

[@khy8]

My router doesnt even have QoS rip

[@TheKillerZmile]

then buy a router with qos?

[@hdtv53cs]

I have bufferbloat on Download but not upload and My router doesnt have any QoS that Works well and I can manual edit how should I fix it?

[@Mr.Machiavelli]

Is it ok to have upnp on while I have qos on, or should I turn off upnp?

[@highconsciousness7563]

Yes, it's ok. upnp is the automatic sense of port forwarding. it won't affect the test. You should however try to have your network as calm as possible. NO downloads, updates, web surfing etc

[@GoldenEagle0007]

if i limit my upload my bufferbloat gets worse and if i max out my download same thing happens. so am having to limit my download from 390 to 300 and my ulpoad is 19 but i write 25 on QOS n seems to help. so weird 😏

[@ozzyczzy827]

So.... I got a 40mbps download and 2Mbps upload. I tried this and it does not seem to work at all. Still having ping spikes or high bufferbloat need halp.

[@just1doit2]

Hey john i just got Netgear xr500, once i use it for my Ps4 i can’t get nat type open . I’ve done everything but it’s no use 😞

[@JohnGlasscock]

watch my latest open nat vid. It shows every way possible

[@l7nalmari189]

I want ur help i just get buffer-bloat only on download .. i use xr500 router (200mg up and down )

[@zirg.]

How do I get to that netgear page?

[@denizhan1010]

I have zyxel vmg3312-b10b how can i fix ?

[@SKnzha]

I always have A* on dsl reports on my PS4 with my providers router/modem in default settings, is it better to find results from my pc instead?

[@JohnGlasscock]

If it aint broke, don't fix it lol

[@kajoak1986]

Hey John, I'm having a problem with my connection. I play destiny 2 on ps4, and i get disconnected every few minutes. There's an error code named 'weasel'. I changed my dns to the Google one and it still doesnt work, do you know what can i do?

[@JohnGlasscock]

I dont have any knowledge of that error code or why it would be happening

[@xXegox]

Its important to fix Bufferbloat but SQM is also very important to not have any problems while gaming. I have VDSL 50k any my G.INP (Interleaving) Values are 13 and 27 (normal should be between 0 and 2) the higher those numbers the more a error correcting algorythm takes action and puts additional latency to the packet. This method also sends data twice if a packet isnt "send" to the server altough it reached the server, so the server actually denies those packets. sry im not native. This algorythm is also used on Fibre.

[@PescaitoFrito]

Im interesting in understand how i can fix the SQM, cause everyone fix their bufferbloat, by reducing upload and download bandwidth, so yeah i want to know more about SQM

[@xXegox]

I use Openwrton a TP Link Router, and their build in SQM.@@PescaitoFrito

[@PescaitoFrito]

@@xXegox Does Openwrton is a function in Tp-link router, cause there are many models.

[@pogiunleashed2143]

I have the xr500, does any of this apply to me since I have the newest router?

[@JohnGlasscock]

You can test it out for yourself and see if it helps. I'm certain the XR500 has rate limit

[@pogiunleashed2143]

Glasscock do you have a Twitter? I wanna dm you

[@JohnGlasscock]

I'm active on youtube comments, I don't use social media

[@pogiunleashed2143]

Glasscock do I have to lower upload and download bandwidth to 70%

[@JohnGlasscock]

@@pogiunleashed2143 Yes, anti bloat and rate limit are pretty much same thing

[@nosleepcantsleep]

on my new router i dont have qos but could capping my upload speed do the trick??

[@quizixs8459]

How do you cap it?

[@nosleepcantsleep]

@@quizixs8459 by configurin it in windows network control panel and changing the duplex. btw it doesnt work it just makes bufferbloat even worse.

[@nosleepcantsleep]

@@quizixs8459 I reccomend getting an edge router x or another router that has good qos

[@Mr.Reality]

idk my router's web page doesnt have this download upload limit thing. I've looked everywhere.

[@WinchesterGamer]

What's better? Your router or netduma r1?

[@frank1144]

Neither.

[@davewasem3242]

When I try to run dslreport on my ps4 pro it says this device may be too slow to test a fast connection. Also, it doesn’t give me a grade for bufferbloat

[@JohnGlasscock]

I got the same notice on my xbox

[@francisco7xj]

So i got the xr500 nighthawk but i don't know how to specifically test my ps4 bufferbloat? I think every time i do it, it test my computer but not my ps4 pro how do i do it?

[@JohnGlasscock]

@@francisco7xj go to dslreports on your ps4 browser

[@francisco7xj]

Omg that's right why didn't i think of of that lol ty man! Great vids by the way

[@leaframos789]

When not even doing anything my bufferbloat is 1,000+ ms.

[@SDkarma4]

Bro... I’ve been having issues with my att fiber connection with putting the pace modem/router in DMZ mode bridging my Netgear router. My speeds are cut in half all the time. After watching your videos about using dsl reports. I’ve noticed everything is all out of wack. Even if I adjust my speeds with the QOS settings. With sacrificing my download and upload speeds it helps but my quality and speed still ranks at at C or less. But my bufferbloat can only rank at a B. Even with trying so many adjustments. I’m planning on getting the Netgear switch. I hope this helps with fixing my latency issues. Thank for the vid

[@zenical4358]

update?

[@skilos69]

I used to get C overall, Bufferbloat D and quality C but after about 1 month of talking with my ISP and fixing it all everything is an A. :)

[@MAXRAY-bw9kv]

how did u fix it ?

[@skilos69]

@@MAXRAY-bw9kv Called ISP got them to replace the shit outside my house.

[@garethwigglesworth8187]

When my gf watches her youtube on her phone it causes bufferbloat affecting my gaming on xbox live. How do I solve that issue? Since she is wireless

[@sangokudbz79]

get a router that can do QoS. On my R8000 I can specify the speed of your internet and it manages that automagically.

[@TrendingPendingVideos]

Is this for Mw3 on Nintendo Wii? So your not host all the time Anyone who plays it will get what I mean

[@undeadhero9141]

but what do i do if im live streaming

[@Noritoshi-r8m]

Thank you so so much!!!!

[@atif6619]

Thanks 🙏

[@sethuser1731]

How can I do this with Fios

[@coveyking]

the modem will generally be the biggest aspect in palliate buffer bloat.....

[@sartajkhan6175]

Reducing download and upload speed do improve loaded latency. I did it with my tp link router bandwith setting.

[@MuhammadBilal-pl4dk]

Guide me dude. I have PTCL connection and i installed a booster to get signals where i use my PC and my PC is connected to that booster which is of TENDA and i get alot of Packet bursts i games

[@sartajkhan6175]

@@MuhammadBilal-pl4dk Bro in my case router towers, internet speed everything was perfect only problem was that ping was high. So i saw a video on youtube to reduce internet speed to get better ping. What I did in my tp link router I went to bandwith settings and set my upload and download speed to 25000kb/s =25mb/s. My normal plan is 30mb/s. Now I get a speed of 21-23mb/s for both upload and download but my ping is very good unloaded is 3-4ms and loaded is 10-25ms. First go to fast.com by default that site will show you only download speed then click on more info and then you will see your upload speed and unloaded and loaded latency. So my trick can only lower your loaded latency by reducing internet speed. For better network, signals, internet speed it depends on your router and if your router is good enough then it depends on your internet provider. First directly use internet to your laptop with ethernet cable then use with wifi and compare.

[@MuhammadBilal-pl4dk]

@@sartajkhan6175 Thanks alot bro will try it. btw where r u from?

[@sartajkhan6175]

@@MuhammadBilal-pl4dk I am from Delhi bro.

[@MuhammadBilal-pl4dk]

@@sartajkhan6175 im from Pakistan nice to meet you

[@MinecraftStuff]

when i do this my ping lowers but i get high packet loss

[@_gr1nchh]

You don't need a router to do this. All you need is a dekstop or laptop (Has to be close to your PC, and ONLY if you are using a console. If you're just on PC, nevermind the entire bridging thing and go straight to getting netlimiter) Run an ethernet cable from your PS4 to your PC. Connect your PC to wifi. Select both the ethernet connection and the wifi connection. Right click and bridge these connections. Get NetLimiter (Has a trial version but is pay for). Once you get NetLimiter, limit the speed of your desktop (Program will have the name of your desktop, it is the top option). Set your download and upload speed limit at 2 Mb/s (You can change the type from Kb/s to Mb/s when limiting it.) My bufferbloat went from around 300-400 on upload down to 10-40. Does it help? I'm not sure. I've only played one game but it seems to be doing okay. Is it as good or as stable as QoS? Probably not. But not everyone can afford a $150 router to fix these issues. It will get your bufferbloat down, though. Take with that what you will :)

[@supernice_auto]

using software like netlimiter is not the same as implementing qos/sqm through a proper router.

[@_gr1nchh]

@@supernice_auto Yeah read the last sentence. And in my personal experience, QoS does pretty much nothing in terms of helping with lag/inconsistent connection. I have a router with QoS and haven't noticed a bit of difference.

[@supernice_auto]

@@_gr1nchh what kind of router and what kind of qos implementation? I'm on openwrt w/ cake sqm and it's made a big difference w/ bufferbloat and is noticeable w/ specific games that i struggled w/ latency inconsistencies w/ in the past.

[@_gr1nchh]

@@supernice_auto TP-Link AC1750. Turned QoS on earlier today and it made my connection worse. Didn't help with anything. My internet's probably just bad though which is what I'm chalking it up to at this point.

[@ramportiink]

I cant limit my bandwith with my router really. I live in Germany and you can only priorize devices or lower the wifi bandwith for other users...............

[@unknownwolf4046]

I fixed Bufferbloat on my old modem i have a Linksys hooked up got. A on Bufferbloat😊 on Xbox one Edge

[@adrianopiraneo334]

The real question is what If i have high bufferbloat or both download and upload?

[@JohnGlasscock]

You can set a rate limit on both or apply QoS

[@Chris-yl3gu]

Can someone explain why my bufferbloat results are better when i am connected on VPN. Without VPN i have B, but when connected on VPN to closest server i get A. Also when i use VPN my upload speeds are almost the same, only download speeds drops from 1000 mbit/s to 200 mbit/s.

[@supernice_auto]

because your ISP is garbage and they are more than likely traffic shaping/throttling your traffic to an extent- with a VPN connection they usually don't do that since they can't categorize the traffic the same way.

[@frank1144]

My DGL-5500 does QoS automatically.

[@allthtrmns12]

I wish my name was glasscock

[@krich106]

Having a Fiber/gig and cable setting. Doesn't really make sense. All cable lines outside your home are fiber, some cable offers gig plans.... Then any service like FIOS saying they put fiber in your home, is false, comes off regular wire to a box in your home to be converted, to not fiber(normally rg6, cat5 or combination). If it was fiber and you cut the line, you'd see light in the dark. Like you would with cable line outside your home. You cannot easily bend it, need tools, hard line, for it passed "light" hence "fiber". What I'm saying is... cable is more true to be fiber, than any other such company. Now if you had a business, cable probably ran hardline fiber right into your building, then you'd have fiber to house 100%.

[@sabrcaptainprice8590]

I get F quality ! But A+ bufferbloat How do i improve quality if i dont qos option

[@JohnGlasscock]

There is info on the DSL reports website on what determines the grades

[@sabrcaptainprice8590]

Glasscock ok

[@beanz_29]

This is the worst video on dsl reports. You didn't even look at the results to see what pings you got. You didn't explain what the idol ping results mean. Very disappointed 😥

[@JohnGlasscock]

I've been doing KZbin since 2012. I've learned is 95% of people that watch my videos don't care about the technicalities, most people are just trying to fix a problem and find a quick solution that works. I've made more in-depth videos before, but that was not the intention of this video. Thanks for your feedback though I appreciate it

[@cameronthegamerx4513]

Can u help me I have copper wire connection and get ping spikes on sky hub WiFi on PS4 I have a WiFi booster but I still get a lot of bufferbloat on upload speed it goes from 50 Kbps to 500 kbps btw way I need a free way or under 100 pounds because I’m not rich also where I live we can’t get fibre help me someone

[@sabrcaptainprice8590]

Lordskipton On ps4 try plugging your router in a wall socket without any extensions or plugs

[@JUBSEA]

@@sabrcaptainprice8590 may I ask why?

[@sabrcaptainprice8590]

Ciro Angel Villarreal Sometimes using two fuse can have an impact performance , direct current in terms of ampere is better than using a plug which has another added ampere Try it maybe?

[@jasony3426]

did the exact thing u told me to do but nothing improves.... still having the D for butterbloat lol

[@TheKillerZmile]

lower the speed on each device.

[@mergulke]

Im having F with fiber man :(

[@michaelvpsp]

Try changing ur channel

[@campos3452]

You get a better overall view in the results. And you can more accurately adjust the limiting. It’s pretty much throttling the upload. With Netduma R1 I throttle upload at 5 Up 30 Down in congestion, but I use a glitch within the google browser because it won’t allow anything lower then 10 setting. And it works well. I can tell when I play COD in system info I get 2100kbs the norm is 4100kbs that it’s working.

[@JohnGlasscock]

Interesting

[@campos3452]

Glasscock Now that I installed the new Duma OS on my Netduma R1 I’ve changed my settings on QOS and get 30-40ms ping on the DSL reports results page/ping bufferbloat graph. I entered 6mbits down and 2.50mbits up for bandwidth and both sliders at 100% with ‘always’ ticked. But setup and results vary from person to person.

[@FlockersDesign]

This dossnt work its the chip causing the problem and this will only get whorse over time not better the best way is look at a mean chips were this is a problem and see if youre isp have one that doesnt use a chip were this problem is known

[@MuhammadSalman7236]

Nice "D" you got there.