Build a 6s Freestyle FPV drone for $200

[@RLC2320]

I don't own a drone and have no business on the channel, but I thoroughly enjoyed your expertise, fluidity of thought, and how easy you made the build look. The algorithm is ‘rithming’ tonight.

[@j.ackermann7029]

haha true

[@eddiehazard3340]

Dude. Why are you on the channel. You have .no. business here. (j/k)

[@otrsixxfo9767]

Lol dat part

[@A-scketchy-otter-lol]

Get a drone sim, see how it feels :)

[@darrinthomas89]

Lol literally just said this like now I wanna build one and feel like I can do it after watching this

[@juantaberner1734]

After a year of practicing in a sim, checking every drone video and reading everything I could, your video finally got me into the hobby! I ordered all the parts at Ali, can’t wait to get this thing up and running 🔥

[@noflifenw]

W

[@juantaberner1734]

@@noflifenw ?

[@itspaysenfpv5634]

A lot of the parts seem to be sold out where did you locate a lot of these?

[@HuskerTheCat]

@@itspaysenfpv5634 same, i found a frame on ready made rc and a camera on rotor riot store. everything else is from getfpv and amazon for me. i did swap a few parts but just look around for similar stuff on other sites. Initially i swapped the VTX and RX for the happymodel Fyjion but then that sold out so i got a Speedybee TX800 VTX and a HGLRC ELRS2.4ghz for the RX. went a little over budget but you gotta do what you gotta do i guess

[@joseph_lacy]

@@itspaysenfpv5634 im in the same boat, i've done a lot of research on other budget parts to use for this build. however i can't seem to find any analog vtx in stock anywhere...

[@neerajdsuvarna3572]

hey could you also share the details on : 1. which remote controller to buy & connect to the reciever 2. how to connect the analog goggles and which one to buy , and on what basis must we buy? I'm a complete noob on this , but i will be interested to build this , if yu couldd guide a bit more on this . thankyou so much overall the video is amazing

[@Ralhead]

Yes that should be helpful

[@Ziyan-fo6zh]

actually, any remote and goggles will be fine, for the remote you can configure it in the desktop app, and for the goggles you dont need anything, it works like a walkie talkie, so you just need to get it close to the drone.

[@Officiallilsosa]

That’s cool 😎

[@NightworksYT]

Not exactly true you set the band and channel for the vtx in betaflight and set your goggles to the same band and chamnel

[@Dinuuth]

I'm looking to use my flysky ct6b transmitter will it work with this receiver? It comes with a 2.4Gh receiver but I don't know how to soldier it to this stack so if I do this will I be able to bind my transmitter with this receiver​ instead of the original receiver my transmitter came with @Ziyan-fo6zh

[@Thrillowatt]

Waiting for the 2035 "build a rideable drone for $20,000" video

[@RichardWhiteman-f8w]

dji t40 🤔

[@MrTehpaul]

A drone is an unmanned aircraft system (UAS) that can fly or suspend itself in the atmosphere. Drones are also known as unmanned aerial vehicles (UAVs). They can be as small as a palm or as large as an aircraft.

[@marxiewasalittlegirl]

Isn't that a helicopter

[@MasterBlakeYT]

Look up the jetson one. It’s bassically that, but it’s a lot more then $20,000

[@makingmadeeasy]

Grant Imahara made one on the white rabbit show for like 20k

[@Sonic_Ox]

Thank you for producing another great video. I really appreciate you posting a budget build for 2023. I'm still analog and I don't have a great deal of money to devote to the hobby so watching you build a budget analog quad with quality components at a time when most guys are going digital AND providing links to where a guy can purchase the components is VERY valuable information to me. Your videos really increase my enjoyment of this wonderful hobby. Your video production value and camera work as well as your CLEAN build philosophy combine nicely with your no-nonsense narration making your videos entertaining as well as informative. Well done. Happy flying amigo.

[@MykolaDolgalov]

0:00 Intro 0:48 Parts list 4:18 Frame Setup 4:38 Motors attachment 6:56 Setting up ESC 33:04 Testing for short circuits 34:39 Tuning the drone via computer

[@jamesbond2905]

Hey i am trying to build this drone but the vtx is sold out any good alternatives for a first timer that wants to stay within a budget

[@MykolaDolgalov]

@@jamesbond2905 The same here. I bought another VTX by Happymodel (combined with the same ELRS receiver, so I ended up using this little board instead of the two separate ones), but then after watching Joshua Bardwell's video I realized that I should have probably bought a more powerful VTX. The one suggested by TRONCAT FPV and mine can produce only 300 mw while to have a good signal at a serious distance your transmitter should produce at least 600 mw or better 1000 mw. In any case, the one I bought and used in my build is this: Happymodel Fyujon V2.0 2IN1 AIO module built in ELRS 2.4GHz EP receiver and OpenVTX I ended up returning the separate receiver because this combined one has exactly the same parameters, the same chips and the same external antenna for the receiver and the same VTX antenna.

[@MykolaDolgalov]

Some more important timestamps: 40:13 Configuring RX Receiver via its Wifi hotspot 42:06 Configuring Flight Modes 43:31 Configuring Motor Direction

[@danielemangia6030]

@@jamesbond2905 Try speedybee tx800 or HGLRC Zeus. More cheaper but less range, HGLRC Zeus nano, that i have used for racing drone

[@NightworksYT]

Won't stay in budget but the speedy bee tx800 is a good option

[@C0RT1Z]

This series has been fabulous. Would absolutely LOVE a similar video for a 3/3.5” build👀

[@hanni4795]

Dahm i would love that too

[@arjunsomnali]

I'd love a non-budget built. Maybe something with o3

[@fufuelhatch444]

What’s a 3/3.5 build bro ??

[@sohamvaidya7138]

@@fufuelhatch444 Drones are categorised by their propeller size, he/she is referring to that.

[@fufuelhatch444]

@@sohamvaidya7138 ohh okay bro makes sense thank you

[@wcianfrani]

Thank you for making another budget build video! I built your 2022 budget build and flew it all summer. It's still going strong and so much fun to fly. It was my first 5" quad and helped me transition into flying in acro mode.

[@TRONCATFPV]

Hell yes, glad the build video helped ya!

[@Boboleboss]

Did you make any changes to the build?

[@wcianfrani]

This is what I used RDQ Source One V3 5" Freestyle Frame $29.99 1 EMAX ECO II Series 2306 2400Kv Motor $15.99 4 SpeedyBee F405 V3 BLS 3-6S 30x30 Stack/Combo (F405 FC / 8Bit 50A 4in1 ESC) $69.99 1 Foxeer Razer Mini Cam 1200TVL 2.1mm Lens 4:3 FOV $26.89 1 5.8GHz FPV VTX PIT/25/200/600/1000mW Switchable FPV DVR Transmitter $22.99 1 RadioMaster RP2 ExpressLRS 2.4GHz Nano Receiver $18.99 1 Foxeer FPV Antenna 5.8GHz Pagoda RHCP Omnidirectional for FPV Quadcopeter TX/RX SMA $12.99 1 Printed Bumper set $25.00 1

[@FIFI_2109]

How long does the battery last on average

[@ozruul77]

​@@FIFI_2109probably around 3-5 minutes

[@comtechyt3436]

watching this video 101th time n finally.....done building my new fpv 6s drone in the same manner and is working perfect!!!.

[@GlobalPoliticsNews-GPN]

How long roughly does battery last? And do I need to buy separate controller and gogles?

[@irrationalideas]

⁠@@GlobalPoliticsNews-GPNbatteries on 6s 5 inch quads usually around 4 minutes. It can last longer just cruising though. And yes you will need goggles and a remote.

[@mikestafford2752]

Show it flying bro...comtechyt3436...plz😢

[@Roundergaming0608]

Bro what's the speed and the range of the drone

[@gp37521]

@@Roundergaming0608 all depends on the parts you get, and the controller

[@davidjpeacock]

Brand new to this hobby, still haven't even bought a controller. This tutorial of sorts was a pleasure to watch. So helpful, incredibly so. Thank you!

[@carmofpv]

It was because of your 2022 build that I was able to assemble my first drone, explained clearly, thank you. I only have one recommendation to replace this frame. The TBS Source one looks a budget frame at beginning, but it doesn't come with any TPU, you're stuck with the antennas hanging down, I lost 2 antennas because of this, the frame is also not compatible with HD, without adding other TPU parts, and each of this pieces costs around $10, in the end this frame is more expensive than a HLGRC for example or a SpeedyBee master v2. But the quality is good, it can withstand a lot of beating, especially the v3.

[@joshlyons1005]

I know you mentioned 2 but which frame would you suggest that has the most documentation and/or ease of build?

[@PhillysHobbyHouse]

Your 100% right, no need for a gopro, the o3 air unit has a lot of camera settings, but I have no idea how to set everything correctly but I will learn! I went the v2 googles so I could get longer range.

[@Carguyforlife]

Yup. I got most of them right. I just bought that camera for my 3.5 inch build. Also on the 2022 build you did I got the T-Motor Velox V2 2306 motors since the Emax Eco's were sold out at the time of my build. I have also since picked up a RDQ Sourceone V5 frame as an extra frame. Lol, I almost have all the exact same parts to build this quad in a 4S. Great video man! Keep up the great work for the FPV community.

[@SifatJudge-ch9hs]

hey when is the 2024 budget build coming

[@mariusz-niec]

I love how you soldered motor wires to esc 😍 I recently build drone inspired by 2022 build and if I didn't cut motor wires so short, I would resolder them. This looks great!

[@laurensholthof]

Are we gonna get a 2024 build?

[@frostyboyee405]

Thank you for this amazing tutorial, u were the one who inspired to build an fpv drone with ur 2022 edition! which was my first fpv drone. i flew it all though my vacation and learnt a lot about the hobby . It is one of my most cherished memories lol

[@DexterMannheim]

This is a very well done video. I like the subtle humor in places. Just wanted to say thanks - I am an American living in Germany and used your video as a tutorial and had no issues getting my insurance, EID, etc. so now I am legal. I will say my experience with the law and drones so far in Germany is positive - I was only approached by the Polizei once (before I was legal) and they were very cool and didn’t make a big deal about it. I hope it stays that way - Germany is a fantastic country for the photography and cinematic side of drones and I hope people fly responsibly and keep it that way.

[@rhyshardaker3891]

When can we expect a update for 2024 build?

[@ayaankhan5589]

Does anyone know how long one battery lasts on this build? 47:41

[@jeffsond]

Awesome!! I considered building my 1st drone but when DJI had 30% discount on the Avata explorer combo I jumped on it. I thought for the Drone, integra goggles and motion 2 controller for $895 I couldn’t pass it up. I may consider your build after I get use to FPV flying. Thanks again

[@5351factory]

Thanks for this, I finally completed my drone. Had a few problems, mainly a driver issue for connecting ELRS to the drone and a bad soldier join. After i fixed that all good.

[@MykolaDolgalov]

Thanks for the great video and a question - I noticed that your final drone at 50:06 has propellers 1 and 2 set up counter-clockwise, while in the video you were saying that they should be turning clock-wise. I finished my build, following your directions 44:49, I clicked "Reverse". What is confusing is that after you click "Reverse" the direction on the chart in Betaflight Configurator is reversed and it is showing the opposite to what the motor is actually doing. My motors are spinning the same way as in the video tutorial 44:34 (not at the very end with props), I have not flown it yet and I am concerned that there was something that you did between the 44:49 point in the video and actually flying - like changing the settings for motor direction, and didn't include in the video. Please help. Thank you!

[@MykolaDolgalov]

I just ended up manually reversing the direction of each motor via SpeedyBee app via bluetooth, and my propellers work the same way as Troncat's drone looks at the very end of the video.

[@AirZeee]

I think I’m right in thinking so long as a the diagonally opposite pair are spinning the same direction, with the left or right hand pairs (1&2, or 3&4) turning against one another, you should be ok? I’ve never built my own so feel free to roast me folks 👍

[@tianchen3452]

Why won’t my Mac flash the firmware. It keeps saying initiating reboot to bootloader. This is my first time building a drone😅. 37:12

[@roblox-hidden-official]

What is the battery life for this drone?

[@joef6398]

Overall a great DIY build of a drone , I've been working on a build for the past 6 months this has not been easy. So many things to setup do , from frames , motors , control boards, ESC, wires and software updates and setup parms . This is the first video I have found that hits most of the above components, though it would be nice to get into why components are picked , I do understand that it would effect the size of the video. But the rest was great for me , this video was a good road map to doing it . Thanks for this DIY video , it has help so much .

[@flo688]

Waited for 7 months for this highlight. Thanks for the great video, you make the best budget builds!

[@ryanmartin5668]

This is the best build tutorial I’ve seen to date. Outstanding job.

[@HunterT72]

Says he can’t sodder and then does the best sodder job I have ever seen 😂😂😂😂 12:09

[@MrBornenjap]

I am a digital system user, every time I see analog systems scattered at cheap prices it really hurts my heart...🎉🎉🎉🎉🎉🎉 Nice tutorial.. already subscribed

[@SL3U7H]

Do you have an estimated range for this by chance? (How far away the drone can be from the controller). Would there be a way to upgrade this simply with swapping some of the parts?

[@TheTortuga58]

Range varies by what you deem acceptable. Most of the time, your video feed will become "unacceptable" before your controller stops talking to the drone successfully. You can up your video strength with better antennas and running the VTX at a higher power. Sorry no numerical answer. If you want a guess as to how far the actual controller would maintain connection, maybe a mile. But like I said, your video feed (lack thereof) would likely stop you from ever getting that far.

[@benthatchervideo]

2:24 what goggles are people using with this?

[@whirlwind9866]

Just a quick question Is this model better and faster than last years Thank for the amazing content and step by step tutorials keep doing what your doing

[@jean-lucandrenavarro3051]

yea, is it better?

[@flipsterfpv]

the one from last year would of costed more than 200 usd therefore probably being better, but i can tell you that this is a solid build, my advice would be to get a v4 speedybee stack as the v3 in this vid had problems such as osd and blackbox not working together, usb port falling off etc, this is fixed from what i have heard in the v4, also, a different motor that is good is the flyfish sword 1950kv, i run these and they riiiippp cant tell you about the veloxes tho, never tried them

[@flipsterfpv]

@@jean-lucandrenavarro3051 the one from last year would of costed more than 200 usd, but i can tell you that this is a solid build, my advice would be to get a v4 speedybee stack as the v3 in this vid had problems such as osd and blackbox not working together, usb port falling off etc, this is fixed from what i have heard in the v4, also, a different motor that is good is the flyfish sword 1950kv, i run these and they riiiippp cant tell you about the veloxes tho, never tried them

[@whirlwind9866]

@@flipsterfpv thank you I have been saving up to build one of these this helps a lot, thanks!

[@TRONCATFPV]

This years build is better and faster. Last years was 4s and had a cheaper ELRS receiver that limited range. This one is capable of 6s, & ELRS receiver in this one has WAY better range.

[@charliedcho]

Definitely the best 5" build video out there. Thank you

[@rockfordian23]

Speedybeef has a nice ring to it.

[@RioGrandeficher]

Bro, I would have happily watched you put that frame together. Badass video

[@jnkfishing9274]

Wheres 2024 build

[@allminegod]

Same question

[@pcolucch]

Where’s 2025 build

[@fortythepirate1119]

​@@pcolucch bruh. It's been 5 minutes haha

[@MortimerFdp]

What's the name of this soundtrack at 47:50 ? I've been looking for it for quite a while without success

[@TRONCATFPV]

audiio.com/gallos/every-day-heros/rest-instrumental

[@YoussefNakhla-kb4tg]

Do i need to use goggels or can i just sync the camera to my phone or save it somewhere?

[@caden_mac]

Most drones you will need a headset system. You can get a cheap analog system from Fatshark for like $150. I’m sure there’s ways you can connect to your phone but you’ll have a really hard time controlling it from your phone

[@YoussefNakhla-kb4tg]

@@caden_mac I meant only for the camera but controls could still be on my controller.

[@dariushenry2787]

Same for me, I’ve watched all your videos about building a drone and I finally build one and it s very nice, thanks!

[@isaakbrochu6358]

very well done video wanted to get into drone building this is perfect. You are very good at explaining and being straight to the point at the same time, good job.

[@knightofthesun1738]

Thank you, Sir.

[@stevemazza]

Really enjoying your content and super energized to start my first build. Never imagined that the FPV drone hobby would be so accessible. Thanks for the excellent tutorials! BTW, you keep saying "splice" when you mean "strip." Splicing is when you join two wires.

[@iankawika]

Finally building my first 5" and this video was pivotal. Thank you for the great info and quality content!

[@Checowdadrone]

Did you do it? Any problems??

[@umbrellahole]

What I want is a long format in depth video of how to build a drone without your recommend parts like an engineering level of understand as to why certain parts go together, why certain parts don't go together and If you can teach the fundamentals of good drone builds vs "buy this" and "do that." If we can teach a man to build good drones and not just give him a drone/parts that are sold out. (You know the whole if you teach a man to fish, feed him for a lifetime mantra.)

[@CooperStewart-ol4jr]

Well I have bad news buddy sometimes u don't get everything you want and people that make KZbin videos don't care if you want them to be your personal teacher you have have to do research and look up how parts work and go together and what to buy and not to buy what you just described is something you can achieve all by yourself you just have to put the effort in

[@umbrellahole]

@@CooperStewart-ol4jr I am just saying half the time the stuff is no longer available due to demand or the video ages to the point you no longer can get the parts. Its not to know how to pick a good part and what makes it good vs buy this do that. I want to know why we want this or that. I am just commenting for the algo.

[@wadye2843]

I was going to buy a DJI drone, but after watching your video I'm thinking of building one as well to practice on before I start flying the DJI, your video is so detailed and cool I appreciate you

[@MacklinFpv]

I had a lot of fun when I used a speedy bee f4 v3 because the esc blew up on me and many other people said it happened to them too that’s probably why they put a heatsink on the v4 so if you do build this it might be worth the investment to go with the v4

[@As_the_Crowe_Flies]

Subbed! What a killer video. Thanks!

[@clint.johnson]

Enjoyed this video. To use the DJI O3 Air Unit Camera Module in this build what specifically would change? I realize the camera and transmitter, but any other details would be helpful. For example, would the Speedybee F405 V3 still be a good choice? What parts to drop, what parts to add to make it all come together?

[@cadenvphoto]

I am also wondering this same thing.

[@supaflymullet]

I've spent hours scratching my head on this as well. The camera and VTX are out of stock so I wanted to go with the Runcam link wasp. Still scratching my head on how it would be setup.

[@noveske.2236]

Hey how much does this weigh? My country has a limit on weight. Max is 250grams

[@rebeli73]

Every country should allow heavier, but you may have yo register those drones and/or do some sort of online pilot test.

[@crazylifehd9088]

a long time i have searched for this Video!!!! I Love it !!!! Thank you sooo much!!!! The Only way to Fly drone is you build it self !!!💗💗💗💗💗

[@bearwolffish]

Yes

[@crazylifehd9088]

@@bearwolffish thank you

[@atk9591]

How long can it fly when at full power?

[@The_Fearer]

any 2024 freestyle 5inch drone build??

[@KythiraBF]

I built the 2022 $200 one, converted to digital, O3. Still flying

[@SalmanSuhail]

That putty hack to hold the tiny parts and cables at 23:38 goes unmentioned and is totally underrated. Best idea ever thank you!

[@Zillawill]

Just ordered pretty much same build thanks to your video, only changes I made was V4 stack, better VTX + a Runcam camera, and Foxeer ELRS RX

[@GlobalPoliticsNews-GPN]

How long roughly does battery last? And do I need to buy separate controller and gogles?

[@Buffdog87]

⁠@@GlobalPoliticsNews-GPN6s is probably about 7-10 min depending on how hard you push your drone and yes you do need a separate receiver and goggles

[@alienware18]

Amazing build and very very on the spot with all the information!!! Amazing teacher skills as well. SHORT AND TO THE POINT. Thank you so much!!!

[@deanroberts1418]

What’s controller can we use ? 👌🏻

[@harrymaxwellofficially]

@Troncat FPV what would change if you decided to use the O3 Air Unit instead of the camera you used

[@Volcano2.0]

Is there another option for the VTX? I can't find that model anywhere

[@LewisBlaylock]

Such a sick video. This is going to be my first built attempt! What control and goggles are you using? I.e models? If I connect the air 3 would that make it compatible with DJI rc2 and goggles 3? Thanks

[@flyjoshh]

If I wanted to use a Thermal camera instead of the budget one... I found an "Axisflying" camera with "RX TX VID GRND and 4.5-18V" inputs.... could that work? @20:40 in your video the board looks to have an "R3 and T3" spot... would I attach there? Do I need the Transmits to the opposing Receiving or straight on? Thank you for your content, just starting to 3D print and want to learn drones and Meshtastic with my kids. Thankyou again!

[@parvezhusnoo8581]

Thank you

[@orcus6286]

Clean and Perfect sir, thanks for your video, i really enjoyed it

[@Donmoncler]

Bro I just got interested in FPV and I’m SOLD. You make it look real easy and enjoyable

[@robertgoldbornatyout]

Thank you for producing another great video. I really appreciate you posting a budget build for 2023.💯💯💯

[@Finyn.]

What controller and the extra thing on the controller do you use again please

[@TRONCATFPV]

I use an Ethix (TBS) Mambo with crossfire module in the back, thats my go-to

[@Finyn.]

@@TRONCATFPV Thanks so much and do you think it would work with 4s to start then go to 6s to try or is it only 6s

[@wuvrsounds9986]

What goggles are you using or which ones are compatible

[@VigalGogo]

best tutoriel i have found so far, amazing, thanks a lot.

[@AirZeee]

I have the DJI FPV drone- was less interested in building my own at that point - any thoughts on how to use the DJI controller with a home brew build? Convincing the wife that I need to expand my toy collection is easier if there is multiple use available. 😂

[@Aperturex1337]

following as i have the same question

[@DigitalXRobot]

1:58 if I use v2 will the drone still work?

[@Asatisfiedguy-b5z]

So I'm planning on building this drone but I can't decide on either getting the 1300mah battery or the 1050 mah battery. I know the 1300 mah lasts longer but is heavier making the drone not as nimble compared to the the 1050. Do you have any advice for someone just getting into drones on what battery to pick up? Thanks.(I love your videos btw!)

[@duikaserver]

what is the purpose of the capacitor? is that not hooked up in series?

[@TRONCATFPV]

prevents voltage spikes when hooking up your lipo 👍

[@Dyonci]

i've been waiting for so long. thanks brother

[@its_key]

LOVE this guy. Great Vid. Also, I love the, "whatever dude"s. Its perfect. I could literally just see someone watching this and criticizing every little thing. I enjoyed this and look forward to my parts showing up so I can start my new build. I bought the last Drone already built, but I am ready for a backup. Thanks again.

[@hshdhdhdsydy]

What would the top speed on this drone be ?

[@JY-cj2xu]

DUDE AMAZING VIDEO! REALLY CONVINCED ME TO START BUILDING MY OWN!!

[@KOKO-GAMING0]

Best one i see make a drone

[@hiddesluijs2007]

for the camera, can i also use the foxeer razer ''mini'' instead of the ''micro''?

[@owe_cp]

What kind of other props could i put on this build ?

[@matthewffs]

Awesome video. Is it possible to add those camera channels on Inav?

[@tiefseetaucherr]

when I go into inav demo mode there is not vtx tab so I don't think so sorry

[@millsidevision978]

That’s Lowell ma at cross point. Nice video I’m planning on building one

[@TRONCATFPV]

Nailed it!

[@amanagement6715]

this video waswonderfull for me ...thank you guy...

[@Rufustudios]

Thank you so much This has helped so so much!

[@Fpv415]

Can i use frsky when use i the frsky protocal?? 38:48

[@lexar4035]

when building a PC, I often find cable management the most fun part. this looks supper therapeutic and almost want to make drones just to make em rather than fly them

[@mr_tamil606]

can you connect the drone to the radiomaster pocket and can you show how to do it

[@mr_tamil606]

Pls do it and show

[@TRONCATFPV]

Process would be the exact same with the pocket 👍

[@Tilenm]

Nice video. I just wonder, how good can you see small objects with such a resolution on goggles?

[@tiefseetaucherr]

It's analog, so yeah it's harder than with a digital video system. But many people still fly freestyle with analog to this day, so there must be something that's good with analog... Get the right vtx antenna and goggles and it will be enough for everything normal human beings need to see :)

[@Tilenm]

@@tiefseetaucherr thanks for the explanation

[@80rex]

mad dank, brother

[@NoahRyu]

Can you please make a 3.5" build video? Thanks :).

[@inamic12]

2 questions, -can you use the o3 unit -this build its more powerful then the dji avata 2?

[@woodlandreconjoshdrakes5509]

I'm just getting into my first fpv build. Your video was a big help. Thank you and I just subscribed. Awesome video 👍

[@ppkus]

Im just starting in the hobby, you got a new subscriber!

[@thataussieaviator]

I already have a "Radiomaster Boxer ELRS" transmitter for my RC planes. I would like to get into the fpv hobby but can't figure out what goggles and drone I should get that works together along with the transmitter I already have, I also don't want something I will grow out of after a few flights. I would like to build my own drone instead pf buying one pre-built and I am familiar with DJI as I have bought a cinematic drone from them in the past, so maybe that's what you may recommend for my Goggle/Camera setup? Do you have any suggestions on what goggles and camera to get?

[@bbkintanar]

i'm brand spankin' new to FPV. I recently got a DJI Avata to introduce me into the FPV world and currently looking around for really simple, budget friendly ways to build my first FPV. I appreciate the step by step process you made! Would you say this is a more beginner friendly drone to build as a first drone coming from someone that has no experience? Or are most builds generally the same process?

[@davidjpeacock]

Just got done building a drone based off this. Not at all budget because I went with an O3 setup. Thank you again for making such a helpful and easy to follow tutorial. I wound up needing to relocate the capacitor because of course the VTX for the O3 is much larger, so I wired that then placed it at the front. Everything else was fairly easy, and of course the O3 was plug and play effectively. One question if you have time please. I set DSHOT to 600 as you indicate, but after saving out it keeps on moving back to 300. No idea if this is a bug or maybe 600 isn't actually compatible and I didn't see it in your video so it goes back to 300? Again, loved this video, and love your channel. Thank you. I gotta get a couple of TPU parts for this baby to keep the antenna secure, then it will be time for a flight test!

[@CodyDane-o7p]

Would a Night Eagle HD be able to fit in this frame?

[@PP-rg5hz]

What parts do you suggest I get if I want to do same drone build but digital ? Keep up the great work for the FPV community.

[@Edzarecords]

already have the googles V2 and I wanna put a o3 in there so whats the best way to do it

[@zorogaming9147]

Broooo can u help meee please😭 I can't get that ovx303 can u suggest other transmitter to connect to that board😭😭

[@Floridamanflies]

I will be build this SOB. Thank you so much for the video and information man. Gives me the confidence to move forward.

[@GlobalPoliticsNews-GPN]

How long roughly does battery last? And do I need to buy separate controller and gogles?