Trimakasih kawan videonya sangat bermanfaat,,, proses membuat perahu dari bahan drum plastic yang bagus sekali❤❤❤❤❤❤❤
@01Bazaar7 ай бұрын
HDPE can be weded with hot air gun and is guaranteed 100%waterproof. With the nails sooner or later water enters
@kevjtnbtmglrАй бұрын
Oh boy, please collect the micro plastics you create with the saw! Peace and love!
@عبدالرحمن-ب3 ай бұрын
Creative man and great work Keep innovating the world He needs work like this
@simondalzell5635Ай бұрын
Great Work. Thanks and Best wishes from North West England.
@davfree97327 ай бұрын
Now reinforce the outside of the hull with fiberglass for rigidity and sealing all the leaks that will come up when the mechanical resistance of the water roughens up and thins the plastic. The workmanship was good... But there is a best practice to making anything that floats on the water that significantly reduces the potential for accidents and/or failures in the material/construction.
@peternicholsonu60907 ай бұрын
Fibreglass over barrel plastic would delaminate. The barrels with sealant would be monocoque by themselves. Avoid over-engineering
@linusgoblin7 ай бұрын
It defeat the purpose of making this a cheap and easy project tho
@rinkinkel6 ай бұрын
Good luck making anything stick to polyethylene.
@thenarrator19846 ай бұрын
@@peternicholsonu6090 Varela are pvc? Both polyester and resin grab that.....
@thenarrator19846 ай бұрын
@@linusgoblinthis is far from cheap. Barrels are pricy and this won't last. So.. pointless
@zistpooya7 ай бұрын
I think your boat needs an inner shell as a floor cover. In fact, the body should be two layers.
@jaabnegat6 ай бұрын
Ładny projekt łodzi! Ta, wykonana przez ciebie jest fajna ale wykonana wg. mnie dopiero w połowie. Brakuje przede wszystkim podłogi oraz zabudowy burt od środka. Bez zabudowy podłogi, stanięcie nogą na dnie łodzi grozi po prostu jej rozerwaniem i zatonięciem! Pozdrawiam
@gacattack12347 ай бұрын
While good work the best use of these barrels is in pontoon boats.
@vertstang1237 ай бұрын
They're great for floating docks too.
@gacattack12347 ай бұрын
@@vertstang123 Good point.
@gacattack12347 ай бұрын
@@RichardLucas Obviously not the best pontoons but best use of these drums in boat form. Sealed cells that for the most part just need mounting.
@gacattack12347 ай бұрын
@@RichardLucas I can't imagine using one of these boats in open sea, that leaves bays lakes and rivers, the domain of pontoon boats. The only requirement that would be better served by these is small size. Oh and speed.
@jozsefpatyi92007 ай бұрын
The best: Straw for storing brandy
@HasanAktuğ-q4x4 ай бұрын
HELAL OLSUN. Çök güzel.
@zbigniewteterycz15715 ай бұрын
SUPER IDEA . POZDRAWIAM .
@mehrcat17 ай бұрын
I really don't think that butt jointing the wooden frames and nailing some plastic patches on will last very long.
@putin-zdoxni7 ай бұрын
Как обработать, минимум 10 лет может прослужить
@The_Oyadi7 ай бұрын
水の抵抗の恐ろしさを知らぬ…愚か者だよ…
@peternicholsonu60907 ай бұрын
Butt joining would then leave you dependent upon the strength of the wood splitting so he likely lapped the panels which would be very strong.
@mrMacGoover7 ай бұрын
As long as overlapping joints of the plastic sheets are facing towards the back of the boat and the seams are sealed with a waterproof silicone adhesive... the boat should last quite a long time.
@silentnight46 ай бұрын
Nails? Agreed!
@chopperhehehe7 ай бұрын
Deffo fit for purpose 😊 👍🏴😁✌️
@AnthonyPhillpotts7 ай бұрын
Excellent effort , viewing from Detroit Michigan USA 🇺🇸
@VicenteLeal-r1y7 ай бұрын
Genial!!.😅
@shawnpwatsons16 ай бұрын
So creative. Fantastic.
@fngrusty427 ай бұрын
Love it . Looks easy enought. Built a few boats out of plywood, this looks great.
@AngelGomez-rl3wu6 ай бұрын
Very good job I likeit
@TV-vl2ik7 ай бұрын
최고 멋진 보트제작영상 잘보고 구독하고 응원하고갑니다 최고십니다
@dreamchangjo7 ай бұрын
아주 멋진 배 입니다. 저라면 플라스틱과 목재 사이에 고무 타이어 조각을 넣어 밀봉을 할것 같습니다....
@Батыр-р2хАй бұрын
А он так и сделал.
@diytoptricks7 ай бұрын
The video was incredibly informative and inspiring. Watching the entire process of building a boat from plastic barrels and wood was fascinating. Thank you for sharing such a creative and eco-friendly project. Highly recommended for anyone interested in DIY projects!
@Heimrik012 ай бұрын
Great job, you're a genius ! Where are you located ?
@ObetPontilan7 ай бұрын
Keep up the good work ...love making...
@faviolubinmorenocamargo50587 ай бұрын
👍 excelente y éxitos
@frayja20026 ай бұрын
1:00 I'm glad i'm not the only goose watching this!
@hwilmore7 ай бұрын
He is a true craftsman. Incredible!
@stonerphil10286 ай бұрын
On peut faire un bateau avec a peu prés tous type de matériaux, il faut tenir compte de la résistance, du poids et de la facilité a mettre en œuvre. le gars fait avec ce qu'il a sous la main, des barils en plastiques, mais disons-le clairement ce n'est surement pas la meilleure solution, la fibre de verre, le bois ou l'alu seront évidement bien préférable plus durable et fiable! bravo tout de même pour le travail et la patience! Je vois tout de même un inconvénient majeur sur cette réalisation, indépendamment de l’étanchéité qui pourrait être moins bonne a longue échéance, il n'y a aucun fond de sol rigide et si on pose les pieds sur les ptastiques en dehors des longerons de bois, il y a fort a parier qu'on pourrait passer a travers ou affaiblir l'assemblage.
@FreeToday-co2oc8 күн бұрын
💪💪💪👍👍
@hzkzakir17866 ай бұрын
ধন্যবাদ ওস্তাদজীকে আমি ১৯৯৪/৯৫ সাধু যোসেপ কারিগরী শিক্ষা গ্রহণ করেছি লেদ মেশিনে প্রশিক্ষণ নিয়েছি এখও এ কাজে নিয়োযিত আছি আপনার কাজে প্রসংশা করি খুবই চমৎকার হাতের কাজ আপনার।
@UNBIASEDCOMMENT7 ай бұрын
Very nice!
@richj1209526 ай бұрын
More work than necessary. I would have made a couple of pontoons, built a frame and structure on top. Mounted a motor and been on my way.
@bernardlonger7 ай бұрын
Economiquement intéressant ,mais le problème c'est que rien ne colle sur le polyéthylène , donc pas facile de faire l'étanchéité !
@hibahprice68876 ай бұрын
That's why it welds together. A soldering iron will help. Well, epoxy resin, as well as polyurethane, PUR.
@hibahprice68876 ай бұрын
Remember how plastic water pipes are connected)
@jomishx6 ай бұрын
That's a pretty awesome build. I don't know how we expected that not to leak. I think I put a roll of butyl and some stainless screws in. Let's go fishin!!
@lenny1087 ай бұрын
Nicely done! The difficulty is all the woodwork to get a solid wooden frame.
@ismedardansitoruschannel7 ай бұрын
Hadir nyimak salam kenal dari kisaran city Asahan Sumut Indonesia 🇮🇩🇮🇩
@velvetrealitytv6 ай бұрын
wow very nice lake
@benskai2475akurfishing6 ай бұрын
Greetings coming from Indonesia, healthy greetings and creative greetings
@BoatbuildingIndia7 ай бұрын
Amazing very nice boat making
@Bowzerbro7 ай бұрын
This is pretty cool, not sure how safe these boats are compared to boats created in traditional materials such as various fibber or just wooden boats. I can imagine these are ok on rivers, but how does that plastic handle sea water? Also I think an improvement would be to use a heated wire cutter to cut plastic or a similar tool. And recycle the scraps too. Using a saw creates a lot of plastic dust, which is both bad for environment and everyone else, while also being very bad for the worker(s). Of course, just reusing the barrel for their original purpose would be an even better use.
@imbranjamil49946 ай бұрын
Amazing tanks perkonsian nya cukup sempal best k
@flyingfox100013 ай бұрын
I think your boat needs to be another 15 foot longer!
@penguinclips95517 ай бұрын
Cool 👍
@КрасныйЗимородок6 күн бұрын
pls, we need more extra plactic
@rbb26176 ай бұрын
Thanks for sharing sir Godbless
@robertblahnik76857 ай бұрын
My neighbor who was a brainiac made a catamaran using oil drums halves back when they didn't have plastic drums. He put them 4ea long ways and brazed them together Then added copper tubing over it. He reinforced the hull by also bridging it with copper tubing. When he was done he sprayed the bottom a lot of coats as he did with the inside. He put an aluminum wave shield in the front. He put a 20hp motor on the starboard side as he operated it on the port side. The first trial checked out but it was completely under powered. So he kept increasing the Hp until the boat balance out. Eventually heard it sank due to an retaliation for stealing someone's girlfriend.
@hibahprice68876 ай бұрын
It is better to weld the seams using a soldering iron and pieces of plastic. Polyethylene terephthalate should be welded. Or you can seal them with silicone sealant. Well, or spend 5-10 bucks on one or two layers of fiberglass, and also make a deck from the same plastic to make it easier to remove water, and add weight to the bottom to make it harder to turn over while standing on the water..
@kurt169507 ай бұрын
wow... good job.
@farhanihwanhadiyin12587 ай бұрын
Benar berarti bagus😂🎉
@cairosouza6 ай бұрын
Araújo caiaque do Brasil
@leonardoquicoyquicoy20426 ай бұрын
Verry nice
@batscher616 ай бұрын
ich Liebe auch diese PE Tonnen daraus kann man viel Machen unkaputtbar
@Cookboy38577 ай бұрын
Nice boat
@hentran38487 ай бұрын
Hay lắm xin cám ơn bạn
@OpaRus716 ай бұрын
Что то грызут меня сомненья что все эти соединения при помощи гвоздей будут достаточно хорошо держать , особенно в полу лодки когда люди начнут туда наступать изнутри давя на пластик рядом с деревом
@sirforsa7 ай бұрын
Yeah yeah, but shop duck! SHOP DUCK!
@MrWetnutz7 ай бұрын
Wouldn't take it offshore or out of sight of land. Always wear a life vest.
@ahmberretima96177 ай бұрын
Excellent travail simple et moins cher je note 20/20 , j'aimerais bien si quelqu'un peut transmettre ça à nos frères en Afrique .Le bois augmente de prix.
@dereksuddreth86726 ай бұрын
No deck inside? I'd probably step right through the hull... With all those tacks, this would be for calm, fresh water lakes only!
@emiliodantonio77686 ай бұрын
Genio
@xtc-7 ай бұрын
слишком легкая, такие манёвры могут привести к перевороту, надо делать тяжелее.
@tranthaotranthao86823 күн бұрын
Sao không làm bằng composite..cho đẹp
@leenonolee46296 ай бұрын
...and it creates microplastics with the saw blade cutting through the plastic.
@MichaelBritt237 ай бұрын
Goose wasn't bothered by the guy sawing right next to it.
@TerryTunes6 ай бұрын
It was trying to get out of there - 1:33. It was distracting from the boat build.
@seyyah39227 ай бұрын
İskelet sağlam olmazsa bogulursun reis...
@pidginmac6 ай бұрын
Everyone has not been on a boat at some point in their life. you are extremely privileged.
@victorllamassr.30296 ай бұрын
Intelligent
@sikhedgamerkamar59466 ай бұрын
Need some fiberglass now
@GildoManoeldiasMendes6 ай бұрын
Como proceder para ver experiment nav egabilidade de um desses barcos?
@jumbleblue7 ай бұрын
how does this not leak?
@evgen07787 ай бұрын
В следующий раз сделайте и говна и палок!
@bryaneaton50532 ай бұрын
Did anyone else see a duck in the garage? He was looking on with those wee beady eyes.
@charlesxix7 ай бұрын
What about the Kill Cord?
@Hefty547 ай бұрын
whats wrong with screws instead of nails?
@fauxque50577 ай бұрын
Bare minimum is ring shank nails. No way I'm risking my life with 1000 little tacks
@inventorysoftware6 ай бұрын
So did you just steal this guy's video and narrate over it?
Сделать пол. А так нормальня лодка. Плтхо что пластик недолговечный.
@VladimirV0006 ай бұрын
На коленке, из говна и палок, Человек делает настоящую лодку лодку!
@안젤로파르디6 ай бұрын
접합부들 틈 사이로 물이 안 세게 하는 방법은 안 나오네. 가장 중요한 과정인데 ㅎ
@failed867 ай бұрын
Recycling isn't using working barrels :D
@charlesyates66877 ай бұрын
Cheaper to just buy a boat . Here in Tampa used plastic barrels are $100 each
@CharlesNewkirk-lb6uh7 ай бұрын
Hahaha 20 here!😂
@shadyking2138Ай бұрын
Just got 6 barrels for 60
@camalisgenderov12197 ай бұрын
Super
@Julios-dx3qn2 ай бұрын
L'idea è buona ma la realizzazione è a tutti gli effetti insufficiente. Comunque complimenti per l'impegno che hai dimostrato. Saluti
@jeremypilot10157 ай бұрын
That barrel he had in the front was full of water, the boat is too light for that motor and was trimming up way too high.
@SirTubeALotMore7 ай бұрын
So how did he really seal that PP?
@dreamboxx7 ай бұрын
with spit
@alee52406 ай бұрын
Norm for river
@howardrewald98176 ай бұрын
Did not see any waterproofing did not see any silicon it would leak water.
@darcysuurhoff7028Ай бұрын
All that chemical leaching off into fresh water ways doesn’t seem ethical
@mikella9596 ай бұрын
help the environment by recycling (uses only new barrels) lol
@ВалентинаМалых-н8н6 ай бұрын
Кажется в стыках не совсем герметично , или " все лодки текут - знай себе вычёрпывай " . Не мне плавать на ней .
@LOOKOUT20127 ай бұрын
A Ship!! Lmfao 😂 It's a canoe! 8hp way over kill for that with a flimsy transom! Crazy and dangerous!
@สว่างภพ6 ай бұрын
ไม่ทนทานเป็นมลพิษต่อสิ่งแวดล้ม
@salehkanan21244 ай бұрын
الترجمة تحجب المشاهدة
@223322user7 ай бұрын
I am wonder, where can I get these plastic barrels ?
@Брат-е8с7 ай бұрын
Дешевле купить ПНД , чем бочку бу .
@ВладимирДавыденко-ь8ю5 ай бұрын
1 бочка это лист 1.6 Х0.8 цена 10 долл . 1 лист ПНД 8мм в 5 раз дороже
@Брат-е8с5 ай бұрын
@@ВладимирДавыденко-ь8ю бочка у нас стоит 200💲еще за доставку 🚚 нужно будет заплатить минимум 400💲 . Чтоб лотку сделать нужно 4 бочки . Теперь сложите четыре раза по двести и плюс четыреста за доставку . Листы ПНД три метра длиной и шириной полтора метра . Цена примерно 300 долларов . Нужно примерно три листа , доставка из магазина до подъезда бесплатно .
@Martin-Zam6 ай бұрын
Прочно ли это?
@pikolo19846 ай бұрын
Jika rumahku dekat pantai pasti kubuat
@jamesperryman23756 ай бұрын
not a ship it's a boat
@дмитрийсавин-ю2б7 ай бұрын
Мужик молодец, рукастый. Однако инженерная составляющая слабовата- у лодки нет единого жёсткого каркаса, а потому вся конструкция получилась хлипкой, и для нормального использования не пригодной