Building the FASTEST and MOST BUILT PW80 on YT | Part 3

Been a while, but we’re back with the Yamaha PW80!!
As all good things go, we’ve had some minor setbacks backs on the build and are discussed in this video, as well as some new additions. The PW80 is well on its way to doing GREAT things, stay tuned for an awesome upcoming part 4…

[@kaileubharvey7213]

Love the vids man got my own pw80 build my self I’m doing rn you should put a yz125/85 kicker on it ! Looks rlly sharp on them

[@GroundGravel]

Good to see ya post again! I still need to put my cr pipe on mine. Excited to see what difference that new carb will make

[@alatorreracing]

Make sure you’re putting a 65 pipe on it. Anything bigger than that is too much for the PW80 to handle with a stock bore, so if anything you’ll be going down in performance. With a 65 pipe and the right port match, you’re flying!

[@GroundGravel]

What pipe are you using then? Cr65 or kx65?

[@alatorreracing]

@@GroundGravel I’m using the KX65 pro circuit system

[@Jude.Rodriguez_14]

She’s back!

[@marafade13]

How can I have a front disk setup like yours? My drum brake doesn't brake at all

[@alatorreracing]

It could be that your brake pads are worn, or a new cable could be needed. If none of that, most of the time the brakes need an adjustment at the drum, and should be good to go! A front disk set up will need to be collected from a 65, along with its front end for direct fitment. I do know it’s possible to have a disc on a stock PW front end, just some fab needed.

[@emilijusmisius4551]

Yea you should defo take the pw out for a top speed run in the next part.Wanna see how much power she gained

[@alatorreracing]

Speed and power aren’t directly related. Speed is determined by the gear ratio that is currently being ran, so we can have a high top speed with an “okay” acceleration or we can have a lower top speed, similar to stock, but the acceleration is explosive! With the 11t front sprocket installed, the gear ratio has been brought down so we should have some nice acceleration when the jets arrive 👍🏽

[@REALISMMODSAC]

@@alatorreracing need to do more on board bro and id go to the 12t and and thenn bigger even more on back bro honest nearly snapped my casing in half with a 11t

[@REALISMMODSAC]

OMFG BRO THIS IS WEIRD ITS LIKE A DREAM LOL I COULDT WAIT FOR UR VID JUST PULLED ALL NIGHTER SPRAYING MY PW80 UP ADDING A KX65 FATTY PIPE. JETTING ALL TONIGHT LOOKING CLEAN AND THIS VIDEO POPS UP ON RECOMENDED OMG NO WAY CANT WAIT WATCHING RIGHT NOW PLS KEEP THE PW80 VIDS COMING BRO THERE THE MOST FUN CANNOT WAIITTT TO SEE IT RUNNING

[@alatorreracing]

Heck yeah man! Had to get a post out for everyone, keep up the build! These PW’s are underrated 🔥

[@REALISMMODSAC]

@@alatorreracing bro your pws pulling fucking hard! can you link the carb and reducer to fit it?

[@alatorreracing]

@@REALISMMODSAC www.amazon.com/Carburetor-Motorcycle-Scooters-YAMAHA-APOLLO/dp/B0B56RG3CY/ref=mp_s_a_1_3?crid=1IN5CXYPZ5FN1&dib=eyJ2IjoiMSJ9.-eMBmnJ0lnGuzsBmXmeUPUHe796acKMScSoPy-DcpK0K1hWKa9993WP3qZIpMOpUwEGxYskGxlMzDUOAE6qMr4eMPXSyzQKlxQUZJ83b5uKPr4cTKtF1CsqZ9zW31bzWM4gvLGAoTXWeMnMd0CibSGv7MJB2aUt-K3fXr_JwMDatUsbRofLXy1bHLZoaDHZF9N1w-3EIGRI1vp8yfjOC1Q.NSS4PplBcndK62WnLhBoK74gfpWGSItlbtmjQFWzKUI&dib_tag=se&keywords=nibbi+24mm+pwk&qid=1713207923&sprefix=nibbi+24mm+pwk%2Caps%2C159&sr=8-3

[@alatorreracing]

@@REALISMMODSAC she’s definitely getting to be a beast! I linked the carb in a reply, the reducer or rubber manifold can be made with a quick trip to Ace hardware in the plumbing section. The one I’m using is a combination of small heater hose and a reducer that came with the $20 carb I originally had on it.

[@REALISMMODSAC]

you got facebook bro?

[@luigicar3883]

Bro you have no clue how to ride