Burris Eliminator Setup and Programming

Instructional video on mounting and programming of the new Burris Eliminator Range-finding Scope. Additional information can be found at www.burrisoptics.com

[@Flyfishtherockies]

Nice, well polished tutorial. Thank you. Its nice to find a video without all the "uh's, um's" and cursing common to so many gun reviews on youtube.

[@je7966]

tx have the Eliminator III but this was still very helpful.

[@Xiongster78]

Can you make a video of the eliminator 6. I just bought one, and i just wonder if I have set the top click radical and windage click to zero before i programming the scope to the burris app

[@sonokillyou23]

Okay that was good can you do one with a 300 win mag or 340 wby

[@MrBundydave]

thanks

[@jamesboow1971]

I think your good at this stuff and I'm the one you talked to on the ps3

[@jpaulthepilot1]

Is there a particular MOA rail needed to mount this scope? Great video!

[@Dynamo55b]

Zero.

[@OEFveteran2010]

I am looking at buying one for my dpms lr 308. I use reloads and woundering how am i gonna setup the eliminator without knowing the ballistic coefficient

[@jorgepena2182]

Hola amigos . Necesito saber como se llaman las dos piezas de mordaza que fijan la base prisma de la eliminator a la base weaver del arma . Las perdi y quiero ver quien las vende .

[@bolonchocolima4321]

jorge peña picatinny mounts

[@H3aleme]

i am looking to fit something like this scope to an HK-G3, does these things last long, do you think it will take the punishment such a rifle exherts?. and isn't the bushnell range finding 4-12X42 scope better... thanks in advance.

[@TOPROLLER101]

Ok its a good scope i got it for xmas but i put it on my air arms s410 pellet gun 995 fps on a full charge how so i set it up for the pellet drop???????

[@MadMalc68]

These scopes any good when used with a lamp for night hunting?

[@williamvanasch7660]

dose it come with picatinny mounts or will i need to buy them

[@carlosemanuelcardenas8662]

Hola,quisiera recibir los video en español gracias.

[@heavyglassglass]

I don't think you need the BC, just the drop number in inches from 100 or 200 yards to 500 yards. My advice is to zero at 100 or 200, then take some shots at 500 and manually measure the drop in inches.

[@shlumpt6282]

After the hunting season is over do you take out the battery ?

[@ghill26388]

I bought an Eliminator and when I have been siting it in after about ten shots the ranger finder stops working. I think it has something to do with the 12 power on the scope. I have read the instructions but can not find out why my range finder keeps shutting off. I would take the battery out and put it back in and that would turn it on for one or two shoots then it would quit working again. ghill26388

[@sonokillyou23]

Dose it work for any rifle

[@franciscochavez3811]

Hola amigos kisiera saver como programarlo aun rifle 338 lapua

[@becca6847]

Bought the scope but don't know how to setup.Wish someone would make a video setup step by ste for Dummy like me... thanks!

[@dandetande288]

Call burris, and they will guide you steps by step

[@andikaputro356]

Kalau saya cukup dengan tali plastik..

[@Courageous_Lion]

HAAAA...you better check the prices on some of those pellet guns!

[@HondaRidercrf150r]

@TOPROLLER101 ur goin to mess up a 600$ scope. GL

[@haideraied7263]

كيف احصل على هذه الناضور

[@metinoremari9001]

اني عندي واحد

[@metinoremari9001]

4-16x50 مثل هذا بس آخر مودیل ..موجود فی محافظة دهوك /كردستان العراق ..

[@johnzarollin2749]

oh that's easy for you to say, jeez!

[@johnzarollin2749]

mounting the Eliminator III Laserscope on the picatinny rail of a AR-10 proved impossible with the very small scope mounts from Burris. The weight of the scope is too much for a single pair of mounts to retain a grip after recoil impacts of just a few shots. Long story short; Burris admitted these 1/2 wide mounts have proven insufficient for mounting the heavy 50 mm Eliminator III. Burris sent, at no cost, another set of mounts. The total is 4 on the scope and Blue Loctite secured the screws. So far this has worked. The scope still must be pushed backwards prior to tightening the Burris mounts. Any slack allows the scope to move backwards from recoil momentum eventually loosening the screws. Hopefully Burris engineers will step up to address their tiny inadequate mounts. Compared to other scope mounting systems they are pathetic, especially for what the EIII retails for, i.e. $1500.

[@franciscochavez3811]

Amigos nesesito ayuda para programar mi eliminator 3 scope ami rifle 338 lapua si algien me agudaria se lo agradeseria