Weld On Super 60 High Steer Kit - Tech Tuesday EP2

On this episode of Tech Tuesday Jake Burkey is showing you how to install our Weld On Super 60 High Steer Arms as well as make use of our ball joint eliminators. The Super Duty Dana 60 ball joints axle is quickly becoming the go to axle for off road builds. We like to use their knuckles on our budgets steering 14 bolt builds. The reason for this is you can run big bell RCVs and big rockwell size shafts and joints and all you need is our super duty dana 60 ball joint eliminator kit. Well then you need some way to run high steer to keep you steering up out of the rocks when rock crawling. That is where our DIY weld on dana 60 high steer kit comes into play. The kit comes with all the plates and spacers you need to get it done. Some grinding to get that perfect fit, someway to preheat your knuckles and a welder is all you need to get it done. If that is out of your skill set you can always either send in your knuckles to have us weld the high steer kit on using our jig or you can order a set of Dana 60 Super Duty knuckles from us with the high steer kit already welded on. All of these options are available at Busted Knuckle Off Road right here in Cullman, AL and we ship Worldwide.
Let us know what topic you would like covered on the next Tech Tuesday with Busted Knuckle Jake Burkey in the comment below and be sure to Subscribe for more!
Get yours Super Duty 60 high steer kit bustedknuckleo...
#JakeBurkey #Super60 #HighSteer

[@BustedKnuckleOffRoad]

Get your High Steer Kit Here- bustedknuckleoffroad.com/products/2005-2011-super-duty-weld-on-high-steer-arms?_pos=7&_sid=82858d9e9&_ss=r

[@caspianfox6596]

I dont mean to be so offtopic but does anybody know of a way to get back into an Instagram account? I was dumb lost the password. I would love any tricks you can offer me.

[@lukeisaac8118]

@Caspian Fox Instablaster :)

[@caspianfox6596]

@Luke Isaac Thanks so much for your reply. I found the site on google and Im waiting for the hacking stuff atm. I see it takes quite some time so I will get back to you later when my account password hopefully is recovered.

[@caspianfox6596]

@Luke Isaac It worked and I actually got access to my account again. I am so happy:D Thank you so much you really help me out !

[@lukeisaac8118]

@Caspian Fox You are welcome :)

[@misfittoys8883]

I remember back in the heydey of internet forums when it was perfectly acceptable to weld steel plating to knuckles for increase in strength, but woe be to someone to even bring up the idea of welding a high steer arm to a knuckle.

[@BustedKnuckleOffRoad]

We no longer do this, we machine the knuckles and key them for our billet high steer arms

[@dr.leonardhofstadtersavage6413]

Awesome video guys, very nice welding. 👍👍👍

[@BustedKnuckleOffRoad]

Thanks 👍

[@SNAGEMNTAG3M]

Would you guys consider making em for a 2005 Dodge Dana 60 ??

[@BustedKnuckleVideo]

snag em n tag em we don’t get much interest in Dodge dana 60s

[@MikeCJ1990xj]

I wish you guys still offered the welding service I was going to buy all the steering and have you weld my bare knuckles up.

[@BustedKnuckleOffRoad]

Our new setup with keyed arms is a way better setup that these weld on ones.

[@zakaroonetwork777]

Pre Heat, Pre Heat, Pre Heat, ... Post Heat, Then Bury it Deep in Sand or Cover it with Layers of Wool Blankets and or Welding Blankets. Navy Tugboat Repair Ship Machine Room.

[@BustedKnuckleOffRoad]

exactly

[@melvinmariott8609]

Like this video. The end of it was funny.

[@BustedKnuckleOffRoad]

The out takes are always hilarious with Jake

[@Will-W]

Fantastic instructional. Note to home fabricators, might wanna take out that lower ball joint if you're putting that much heat into the knuckle. Or not, i'm not the boss of you.

[@BustedKnuckleOffRoad]

not a bad idea

[@gafrers]

Greatly explained

[@BustedKnuckleVideo]

gafrers jake knows his stuff 👊🏻

[@BustedKnuckleOffRoad]

Glad you liked it

[@melvinmariott8609]

Yean im ready to see them back on the trails in north east Oklahoma.

[@BustedKnuckleOffRoad]

where? Jay?

[@melvinmariott8609]

@@BustedKnuckleOffRoad yeah been wanting to go camp out up there an see them run.

[@TheRoadhammer379]

Hello, can the ball joint eliminator be utilized on the 92-97 Dana 60 axles?

[@MichaelBrown-jv4xg]

Can these be used for double sheer for a full hydraulic double ended ram?

[@BustedKnuckleOffRoad]

that is what they are designed for yes

[@matty86suk]

Will these work with 99-04 knuckles? The BJ eliminator?

[@BustedKnuckleOffRoad]

sure will

[@scothansen3779]

Yup, just installed the ball joint eliminators, don’t forget to grind the top of the bushings down until you get about 25lbs of pressure to turn the knuckle free play.

[@tonybolt3384]

Which ESAB welder are you using? Rebel 235 - 285?

[@BustedKnuckleOffRoad]

235

[@TheFonder19]

Love the videos but would like to see proper ppe so a younger generation also does The same

[@BustedKnuckleOffRoad]

What did you see that was missing?

[@TheFonder19]

Gloves when guy was grinder

[@BustedKnuckleOffRoad]

Gloves are a good idea. Atleast he had on safety glasses.

[@summitdave8782]

@@BustedKnuckleOffRoad ...Well cant be baby sitters...Thank god...lol...

[@muds17]

I usually stuff tampons in my nose so I don't breathe in the fumes also

[@martynvanlancker2364]

Love the educational outtakes...when you weld something it gets really hot 🤣🤣🤣🤣🤣

[@BustedKnuckleOffRoad]

the outakes are our favorite part!

[@marshallborges9606]

Messenger on your link is a deterrent; to me at least

[@BustedKnuckleOffRoad]

it just helps people get a hold of us the fastest