C3 Electric Headlight Actuator System Conversion, Corvette 1968-1982

Purchase the Conversion kit at:
www.corvettepartscenter.com/c...

[@jessemarinjr6374]

GREAT VIDEO LYLE!! VERY HELPFUL ,THINKING ABOUT CONVERTING MY 68 VETTE OVER TO THIS CONVERSATION. !!! THANKS AGAIN FOR THIS VIDEO . JESSE VIA LAS VEGAS

[@user-hv1xv4xx9q]

I just purchased this kit and it works really good just follow the instructions.

[@ralphmeder7842]

Just bought my kit for my '73 from Eckler's! My car just came back from paint and body less my new front bumper and light bucket assemblies (he kept them to re-shoot). This leaves me all the room I need to mount this new kit and hook up to my newly-painted light assemblies.

[@randywatsonii3173]

thanks for the entire list! I'm gonna try to macguyver this.

[@sergio74v41]

Holy shit! This is the best vid on this! I ve seen some where the whooole steering g column comes out! Unreal❤

[@randygarza3001]

Awesome video.

[@juanb.5789]

great video thanks for making it.

[@motorcycleman-go4708]

Very cool. cheaper on this site then I've found anywhere. hard as a rock for my headlights that work now

[@gadsdonflag4289]

Wish you had shown this hooked up and working on a car so we could see the difference......

[@driddle8534]

I would like to see motor kits for the heater vents too! Keep the vacuum just for the bare necessities!

[@sammyjs291]

Great video, thanks, Big Help!!!!!!!!!!!

[@haganahmerkava4137]

Thanks.

[@Chris-hq7nl]

Thanks so much for this! I have this kit ready to go on my '80 as part of a complete electrical system overhaul (along with removing the vacuum system). Would you recommend taking the headlights completely out of the car as they have been in this video?

[@lyleaulwurm9486]

It would be unnecessary to remove them like I did for the demonstration....all of this can be done with the lights still in place. Lyle

[@barrybenson2840]

❤❤❤❤❤❤❤

[@JS60SIX]

Would of been nice to see it work.

[@DiscoGreen]

Link to the control module? My Miata motors came from eBay and have no pigtails... Everything's installed but I just have 4 wires out of each. I know the green is indicator lamp

[@jarrettslee1]

Can we see one installed and how you incorporate it with the turning the lights on.

[@csvette]

The system uses your existing headlight switch, so everything works just like factory. Lyle

[@jlaceymedia]

Just tried installing this in my '82 but the fitment of the motors against the radiator is too tight to complete the install, even after jamming them (hard) into the radiator fins. Not only do I now have bent radiator fins, it seems the only solution is to drill new mounting holes in the actuator headlight assembly which is very frustrating considering this was supposed to fit out of the box.

[@csvette]

James, there is something amiss in the car itself. Call me at the shop 800-886-5064 Lyle

[@rodnichols9211]

Good Video. You say there is only one wire hook up, and it goes to the stock switch. My 68 switch can not be assessable unless the whole dash is removed. I hope you have the wire color down stream that I can splice into. Your video did not show that, which is very important for us working on these old old cars. I see it comes with a electronic device which has to do something. Where is that mounted? Thanks, Rod

[@csvette]

There are actually 2 wires. One goes to the alternator, the other hooks in to a sidemarker lamp. No need to touch the switch in the dash. Lyle

[@petercarey6883]

Once again, this is an excellent instructural video. It would have been nice if you showed the actual conversion in operation and the amount of time to get both headlights in sync with one another. Is there such a conversion for the C3 Wiper Door? Save the Wave.

[@csvette]

The Headlights sync automatically, as they are both controlled by the same brain box.

[@petercarey6883]

@@csvette I only asked in that the C4 could occasionally be out of sync, although nothing like the original C3 setups. What about an electric conversion for the wiper door?

[@csvette]

There is an electric conversion for the wiper door as well, but it is from a different manufacturer. That system costs about $1300, and while it works really well, I think that is too much $$$.

[@petercarey6883]

@@csvette "Too much $$$" Now that is an understatement. :-)

[@csvette]

@@petercarey6883 The travel on this setup is about 1/4 of what it was on the C4...we have them installed on a car here and they are instant and simultaneous. I'll add some video of that car working when it gets back from cut and buff.

[@codestar7]

I ordered a kit and I got no connectors in the kit. This is the harness and the wires I got. Maybe you know what connectors in the light switch to connect them to? I was going to upload a picture, but KZbin doesn't provide for that. If I had an email address, I could send it to you. Anyway, at the end of the dual harness that connects to both motors and the relay are a black a blue and a red wire, stripped. Any Ideas as to what connectors on the light switch they would connect to?

[@raaedalhaidar6709]

What gives the signal to open and close the headlights? There is no switch in the Kit.

[@csvette]

That is because this system hooks into your existing wiring and uses your original headlight switch to actuate the headlights.

[@raaedalhaidar6709]

@@csvette Thank you

[@eclipsetravel4926]

Can you remove all the vacuum lines and associated parts once the installation is complete. I have a 75 convertible.

[@csvette]

You can eliminate the vacuum actuators and the vacuum relays under the nose, but I would leave the connections to the vacuum reservoir in the front frame extension--you only want to thin out the headlight vacuum that is no longer needed--the rest of the vacuum system has to remain functional for HVAC and other non-headlight functions. Lyle

[@eclipsetravel4926]

@@csvette Thanks!

[@andresgalletti1986]

I see a lot of people getting these conversion kits say that a slot needs to be cut for the actuator arm to move now. Is that actually true?

[@csvette]

Not with this kit. there is another kit on the market that doesn't use actual Corvette motors or module, and that one requires more customization to install than ours. Lyle

[@lippy0160]

Where do you order this kit? And a price?

[@csvette]

$675 shipped anywhere in the US on my website at corvettepartscenter.com. Lyle

[@jc-aquatics191]

Wow nearly $700, i think im just make my own.

[@GoldNuggetGarage]

Where do you mount the module?

[@csvette]

LF inner Fender near the alternator. Template included. Lyle

[@user-xj8ot1dg5t]

Which site sells the most reliable set?

[@csvette]

We Do. corvettepartscenter.com. Lyle :)

[@gregwaltz162]

Not one word about electrical hookup, how to I hook up the electrics

[@csvette]

Wires directly into the front lighting harness. No dash removal, no new switch. Super easy. :)

[@rexrunner]

Light brown wire to headlight needs to get tapped into, a ground and a positive

[@vitalirider707]

When i can buy parts for vette c3?

[@csvette]

Call our shop at 800-886-5064. We have an entire Warehouse full of C3 parts. Thanks! Lyle

[@vitalirider707]

@@csvette web site?

[@jessi74]

@@vitalirider707 corvettepartscenter.com

[@rexrunner]

I just installed a kit. The motors cycle to full lock when lights are turn on but never retract back down. Checked all voltages. Kinda lost. Already left you a voicemail since I know it's the weekend.

[@csvette]

Call Dave (the manufacturer) after 10 am Eastern Time. He knows everything about this system. His number is 904-248-9549. Lyle

[@jeffstack4217]

I’d be embarrassed to call myself a professional and use Ryobi tools.

[@lyleaulwurm9486]

Take it from a professional that has been doing this for 46 years...tools don't make the man. There are a lot of Snap-On devotees who couldn't fix breakfast.

[@peter455sd]

Whats wrong with Ryobi ?