SolidWorks sheet metal Tutorial | Calculate flat form of Elbow in Solidworks

[@muhammadfouad1792]

Really grateful for the existance of such channel on KZbin 👍👍

[@charlestoneoyoo]

Learnt Sheet metal with the help of your channel in August 2023...I'm grateful always!

[@gregoriocl5599]

I appreciate all your teachings, and your generosity in sharing your knowledge. I suscribe

[@manuboker1]

Thanks! wonderful SOLIDWORKS instructing videos! 😎

[@sureshnair701]

Too Good, Thanks for the video. Learnt a few quick tricks in the process as well.

[@tahayousefinia9938]

Excellent educator, Thank you

[@MdRobiulIslam-cv7hu]

Excellent job sir, i am reqular viewer of yur channel and taken lots from you

[@ronblais911]

Great Job as usual..tks for thinking of the little guy for explanation...

[@imshaikh3489]

Dear sir, We are in pressures vessel industry where we make many miter bend, above videos shows how to make the elbow, but it doesn’t show the orientation of weld seams, for each part there will be a separate weld joint and each joint must be away from each other. It will be great help if You how to do it. Thanks a lot for your great helpful videos, I am learning a lot from it.

[@ermdallauddinansari1948]

Beautiful PROJECT sir

[@chikis2046]

Thank you very much your video helps me a lot, you make everything easy. God bless you

[@Verificador119]

Thank for teaching us

[@przemyslawbober5035]

amazing lesson

[@ابوالفضلجانباللهیفیروزآباد-ص4ي]

Thank you for your useful video. I had a question about how the inlet and outlet diameters of this channel would be designed if they were not the same and if the channel was made up of 5 pieces?

[@รัชชานนท์-ท4ห]

Thank you sir

[@ALFURQONTAWABI]

thank u , very helpful

[@Road-2011]

Спасибо за видеоурок! Как всегда, все понятно и доходчиво. Успехов.

[@maticsajovic8792]

Good tutorial, well done.

[@nardaoeletronica]

5 stars, excellent.

[@emmaromero7125]

Muy rápida la explicación 👍🏽👏🏽

[@inusahmoro577_gj]

Thanks for your tutorial.

[@akhimienpatrickpascal9265]

Thank you for this video man I really like it thanks

[@louisbayamunya7620]

Good Job

[@sydamir7100]

hi sir Iwant to know how can print this flattern with a simple printer and a4 paper in real size for cutting with hand tools .thanks

[@jeremye21]

I am in SolidWorks 2019 and I can't use the edge of the cut in the middle of the pipe to make a bend, what should I do?

[@yamenakesh1369]

Thanks from my hart

[@giancarlo562]

i have a question, you have to consider that 1 mm when you delimit, right?

[@Rosk03]

Thanks !

[@rakibhasanantor4567]

hello. I have been watching your videos for many days. they are really helpful, i have learnt many things. Now I request you to do some videos on how we can install easily "Power Surface" and "SolidCAM" on solid works. It will be very helpful if you do it. Thank you

[@WHCAudio]

Excellent. I have a job I'm bidding that will require exactly this. Now, how would you measure what the outside radius of the elbow is if you're trying to re-create an existing one? Same typical way you'd measure a corner radius on any given object? Or is there anything special when it comes to a segmented elbow like this?

[@hutch2827]

Informatives Video.Danke

[@ahmedemara8527]

good job

[@johnwalter9527]

Sir, Very nice.Thank you

[@dmixsanjaymandhi6455]

Sir please make a video on volume of A cylinder cone and other shape 🙏

[@hagerkhaled5328]

Good work.. But there will be a big problem. In actual life we avoid to make any.. Cross Weld.. So some parts must be mirrored

[@kandasamyrajan]

Thanks for the video.

[@kk-rq7jg]

Bro before my forming tools were small in size now its extra big how to adjust size of forming tools

[@cheerwang9419]

Thanks for your sharing.

[@mohamedmamounmamoun7231]

when i do the shell part, the other face still in the part. what i mean is that one one face is removed untill the second face only. the second face still exist, how can i solve this problem.

[@christoperornelas7809]

excellent.

[@Mr.MingJin]

I did like your instruction but it noticed that: "fail to save file", can you tell me the reason, thank you!

[@pandiarajanmechanic8020]

Thank you sir.....

[@shkher1]

Very helpful video for beginners. Can you guide in drawing a duct which has one face circular and the other a square?

[@jeffmanges874]

Can this be done with a cone?

[@maz1980s]

Thanks for the great video. How about a mitered reducing elbow? I'm having a hard time modeling it.

[@tomas89se]

Can you make same tutorial but in Inventor ?

[@DudyOne]

What type of mouse or controller do you use for Solidworks?

[@فجرالصادقين]

challenge for you ... can you flatten conical helix variable steps

[@yilmish84]

İ like your video very much. thank you. But can we show both of suppressed and unsupressed models at the same drawing sheet?

[@mohamedibrahimewahba3718]

perfect

[@lomishkumar555]

Circle radius is equal so don't dimension twice

[@muruganappasamy8494]

Instead of using shell command in the beginning, can we use Thin Feature while using Swept Bose command? How is this different?

[@amirdhalingamlingam1080]

Hai Good evening how create bill of material sir

[@DeepSingh-nm2uf]

Sir tell me how to measure radius in autocad which according we can marking on sheet

[@mohammedqutubuddin2338]

Sir can you it on cone at 120 degree

[@brunocaballeroesprella9311]

sir got question do you think you can measure 656.89 on an a sheet metal? or do you have to round it to 657.9?

[@trivedinishang1432]

Structure system ka use kese kare?

[@thomasgaber3098]

Is there any way to have alignment tabs to keep the elbow pieces at the correct orientation?

[@marcelobordao6729]

Thanks

[@chikis2046]

I am looking for a similar elbow but the one I need is square not rounded, do you think you can help me?

[@thomasgaber3098]

Make a square sketch as your sweep.

[@vishnudathk1828]

I cannot select insert bend on edges..it's showing 'this edge cannot be selected'.. could you please help me with this?

[@mecmac2699]

I recommend you to choose the hole face, and then convert entities, then trim additional lines and keep the edge you want to choose.

[@mr.laxmanraodandra2078]

Please make a video on how to convert solid work to AutoCAD with exact dimensions for any drawing

[@dagduchickhaley5497]

What type of elbow is 1R,1·5R,2R..there must be some standard dimension.

[@dhorpatanengineering1912]

please how make a cantileaver steel bridge a video

[@ahmednessim4542]

would you help me with a link for solidwork software and the crack

[@dhorpatanengineering1912]

nyc

[@akibshaikh4675]

HOW TO MAKE SHEET METAL EXHAUST DUCT WITH DIFFERENT CROSS SECTION ON BOTH END. ONE SIDE RECTANGLE AND OTHER SIDE CIRCLE

[@superkevinkevito]

I would use a loft with two sections, one rectangle and the another circle and a path, then divide as the video.

[@farzadabbasi3004]

Great ...

[@dalvadigaurang8234]

What is the reason to give a insert bends

[@CADCAMTUTORIALBYMAHTABALAM]

Dalvadi Gaurang without bend insert cant be flatten the pipe sheet, we need flatten face for cutting.

[@assadabdulwahab6452]

Hello and thank you for the tutorial. The thing is when you pattern the elbow parts , you get 1874.54 as shown in your drawing. and when we make the perimeter calculation we get=3.1416 x 600=1884.96 How we can resolve this problem? Thank you.

[@ubusstard7361]

When you convert to sheetmetal, ensure the K factor is set to 0.5

[@deepakchaudhary6057]

Sir...weldment ke upr koi video bna do.

[@locatingyourself]

Explain 60 degree elbow

[@ParvezKhan-vi6jm]

😮

[@musadlinimardan4502]

Hello, greetings is it his original or pirated solidwork ??

[@kailaskumarl5510]

Please give the details of transition piece Circle dia 4980 Rectangle dimensions 4398 and 4567 Length bw transition piece 2500 Please solve it and give a lecture

[@thelibras2007]

What if the elbow is less than 90 degrees?

[@thomasgaber3098]

Just make the degree measurement in the beginning. Instead of a quarter circle. I just did one at 72°

[@leandrofontes6746]

And how do you do a conic curve? With different diameters...

[@nayeejatin461]

Sir cleane room furniture items vidios requirements like sheos lockers, staff lockers dust bin, crossover beanch, cabinet, all pharmacutical company required in solidworks tutorial please

[@airtel1730]

my insert bend option not showing !!

[@pandiarajanmechanic8020]

hai airtel > goto search command bar type as "Bends" r goto Insert>Sheetmetal>Bends.. i hope u it will work....

[@agoagoagoagoago]

Video is unclear, Could you show the section and interferring parts at end of the video?

[@rhyzx]

This is the fastest way to do this

[@thierrycaillet3983]

c'est beau

[@gablubpor]

Why There isn't a button for repeating this process insted of wasting time doing it all again?

[@WHCAudio]

You can make a macro to do that I believe.

[@jay-rj9qk]

Do you have any institution

[@CADCAMTUTORIALBYMAHTABALAM]

not yet have future plan,

[@rubanbritto]

Ok

[@ketankamble.2004]

Are bhai hindi mein bhi bataya kro yar 😊

[@muratsuslu8200]

hocam bu çizim çok kolay bir çizim

[@tuhinislam197]

Your tutorial is fine but video do not clear

[@adityajanuararifin3286]

madep

[@sojolsojol674]

yyy

[@RaviSingh-vz9vj]

Very poor soluctiion

[@markbarry881]

thanks

[@lanhvo7589]

excellent.