CAM and CRK & Wiring Diagrams

[@ADPTraining]

Thanks, we appreciate that. All we ask is some participation like you just did. Thanks for sharing.

[@ADPTraining]

We use the Scope-1, which we make and the Fluke. Thanks for commenting.

[@ADPTraining]

Thanks for posting. IMRC module is found only on FORDs. Post back for clarity.

[@ADPTraining]

Thanks... We now have a new SERIES on how to make your own equipment. Keep watching...

[@ADPTraining]

OK, for sure... you have a loose ground. Somewhere you lost a ground wire to the engine block, the chassis or at the battery. Try not to crank it. This could blow your modules (computers) and make things worse. Just turn the ignition key and hunt down the open ground circuit. I am assuming that your battery is fully charged. Post back with more...

[@nattvuthjanmala7052]

ADPTraining

[@duncanmcconachie1765]

what wire is positive on a 3 wire blend door actuator

[@pauloagasa4924]

Hi ,im new here.i have a loose ground while trying to start my ford everest.did i just blew my pcm?i checked my pos.supply of my ckp sensor but im only getting 2.3v.

[@CrossingEarth]

This is actually a great video.

[@ADPTraining]

Thank you... I also invite you to review our current SERIES "How to Build Your own Diagnostic Equipment", right here on our FREE channel. Click the link towards the end of the video or click ADPTraining and choose the playlist. Thanks again.

[@onefastbob]

Pretty good video on the basics of those sensors. Thanks

[@ADPTraining]

Thank you. We also design and make the test Rigs for these sensors. www.autodiagnosticsandpublishing.com/

[@renejacques8288]

I have a 95 maxima. I have a two-prong camshaft. Should I test the camshaft for voltage or current and how much? Thanks.

[@ADPTraining]

Use an oscilloscope.

[@atomicdmt8763]

thanks! i recently put in a NEW (but bad) CKP sensor and its apparently shorted internally- screwing up my fuel level gauge, ignition coil/ignitor(?) and setting off a host of other selonoids- et al! I cleaned all grounds, rebuilt my fuse box, new ECU, cleaned everything........no changes UNTIL i just now decided to swap back in the old CKP sensor. All the electrical clicking, etc went away immediately and Im not going thru the KEY RELEARN process for the new ECU

[@ADPTraining]

Crank sensor may share 5 volt reference with other sensors. You're not giving me much, such as year make model engine size. Looks to me that something else is the cause.

[@adilmehmood5672]

Dear Sir, Can you plz elaborate the ECU connections in future videos? Such as assigning the connection name @ ECU i-e NE+ and NE- in case of CRK Sensor. It would augment the lesson for sure.

[@Dogsled1000]

I have an 06 Jeep and the ABS cam sensor went bad. what is the procedure for testing the sensor on the vehicle once you know it is getting power

[@ADPTraining]

We have other extensive videos on that here in this channel. Look it up and good luck...

[@Mark1944089]

Can a Lighting Control Module on Ford's can cause the engine not to spin? My interior lights head lights are not functioing properly, the car stop on me today then that LCM started to click like crazy and I also had a P0443 code on it evaporated small detection

[@jeronimochief]

Great video, what type of handheld oscilloscope it is and where can it be bought?

[@TARHAS643]

Thank you very much 👍👍👍👍👍👍👍👍👍👍👍

[@ADPTraining]

Thank you for posting

[@W.Khairi]

Very nicely put, Thank u very much

[@danecarby4943]

My1999supercharge estimate not getting any egnition current change coil and.crank sensor and the still. No current check ecu its OK need some help.please

[@shaukatalishaukt5478]

Can you help me ecm parts number

[@amazingmikee]

My cam sensor (3wires) has probably a bad ground form the ECM. With a disconnected sensor the gound measures +3voltage. Looks very suspicious to me. Can i cut the ground wire and mount it directly to the ground? Or does it need to come from the ECM?

[@ADPTraining]

The issue is this, if you run a different ground, then the ECM will compare the signal to whatever the ECM thinks it's a ground. That will never work. You need to find where the ECM is grounded.

[@ADPTraining]

Thank you...

[@rasalvai_1022]

Very nice video viral 👍

[@Артем-ь7б8р]

Класс 😉👍 Побольше полезных схем и сто не нужны будут 😀

[@ADPTraining]

Spaciba

[@mustafamahdi3161]

dear sir . could you tell me what is happening with my cruise car . i changed the crankshaft it was damaged but i have P0300,P0303 and P0304 no one knew whats the problem !!!! I replaced ( ignition coils,fuelpump,plugs) and( no leaks ) i checked the injectors no problem with them . I checked the crankshaft with voltmeter ( 2.5vdc wite and blue wire, 2.5vdc green wire and the third wire is black for ground) these readings with ideal engine. are these correct readings I need your helpe sir.

[@jameslyster6742]

Good day sir thanks for these useful information and knowledge shared I just want to ask some issue regarding IMRC solenoid malfunction on chevrolette lumina model 2007 v6 engine intermittent issue how does it really works? thanks a lot and more power

[@javierjuarez3995]

james batw

[@jma8352]

i got 1.5 volts to both wires grounding the neg wire to bat neg. getting no spark on cam/ crk system 99 ranger 3.0

[@ADPTraining]

1.5 volt at the sensor? Please be more specific.

[@nafiujafaru7]

👋

[@omarfadhil4310]

hi i have VW passat 2001 the voltage i get to the sensor is 5 + DC volt only not 12 v is it ok? and how much should be the signal voltage?

[@W.Khairi]

informative as usual...Thank you very much

[@ADPTraining]

👍

[@scottnevel6177]

I have a 1997 Jeep Grand Cherokee Laredo. It lost power and shut down. During my testing of the CPS I found I no longer have 12 volts at my wiring harness to the CPS. Didn't know if there is an actual test or how to see where I am losing the power.

[@leonjackson1154]

2002chrysler Sebring ran hot now no start no fire or fuel

[@friendofvinnie]

Scannerdanner KZbin channel does this test on your make model and year

[@stevedelong9353]

What color wire comes out of wire loom and goes to which wire on plugin color code will have to replace plugin

[@alexparks8752]

Mine has 3 wires. Black black red with white stripe

[@CynthiaGragg]

Did you figure this out cause mine has 2 black and looks like a brown or a red I need to know the pattern

[@mohammad45h]

Thanks you. Thosans 👍.....👍...👍....

[@ADPTraining]

Thank you, www.autodiagnosticsandpublishing.com/OBD_2_DLC_Health_Checker.html

[@christianbwalyamwewa3303]

Pls,advise me on the location of crankshaft position sensor and ground for ignition coils on toyota duet ej- ve engine

[@brandongarner3397]

Can you Mr. Ive been struggling trying to figure out whats been going on 3 mechanical decline shops couldn't figure out what was going on with my cousins 1994 s10 blazer tahoe edition 4.3 cpi or ipc- pci obd none after intake gasket replaced motor would be fine one day the next rain would wash the blazer away. Cousin handed the keys over to me, came with the original window tag $ 21,350 with caset about the csi blazer. Doesn't explain my situation car now starts up runs at tdc 0 prrrr warms up then dies wont restart i noticed the crank sensor on passenger rear head was wobbling around and hand tightened. My question is this would that create my problem?

[@ADPTraining]

You need to train yourself, not wait for the problem. See my PDF Ebook and software packages. autodiagnosticsandpublishing.com

[@nafiujafaru7]

Hi 👋 pls I need knowledge from u base on automobile electrical

[@markrampersaud]

yo nice stuff man keep up the good work

[@elricocloete9095]

Does jetta 3 carburator have a tci box

[@terrencewilliams2813]

Very informative video

[@ADPTraining]

Thank you, see our CAM and CRK Simulator here. www.autodiagnosticsandpublishing.com/ecm_reference_voltage.html

[@donnadavis8450]

I have. 1998 ford explorer ( EDDIE BOWER) , Where is the cranker sensor located?

[@ADPTraining]

Front end engine or bell housing.

[@nigelclark7360]

Very good info

[@ADPTraining]

Thank you. autodiagnosticsandpublishing.com

[@roslanhusin2244]

Hi..my car cps sensor hv 3 wire, can u make vid using 3wires sensor and how to chck the reading 2. What is the sensor type? Magnetic or proximity or else

[@ADPTraining]

This is called a Hall Effect sensor. It has a small transistor inside. See more here... autodiagnosticsandpublishing.com/

[@Engineeringmaster-x7m]

Thanks you very much Sir

[@ADPTraining]

Thanks for posting. See our training downloads here. autodiagnosticsandpublishing.com/

[@SavageShooterX]

I have a 08 impala just changed the sensor cel still came on my connector clamp is busted help please

[@nigelclark7360]

Very good

[@ADPTraining]

Thanks Nigel... autodiagnosticsandpublishing.com

[@Mark1944089]

I have a 2003 Mercury Grand Marquis Gs When I turn the key the motor doesn't spin and the light on the dash dime a little but when turn the key I see no charging light but when I turn the key to start the brake light get brighter

[@CARAIRCONTECH]

nice

[@rafihussain]

Right. Thanks

[@ADPTraining]

Ok

[@belindaholguin2428]

Why does my number 5 coil keep on shorting out and melting.

[@ADPTraining]

You have a bad GROUND to the coils.

[@roniharyana796]

Tank's buat info nya

[@ADPTraining]

sama-sama, periksa peralatan saya juga. Saya mengirim ke seluruh dunia.

[@Blksheep_619]

🙌

[@ADPTraining]

👍

[@arivuazhagan442]

Thanku sir

[@ADPTraining]

Thanks for posting... www.autodiagnosticsandpublishing.com/Automotive_Diagnostic_Repair_Book_Catalog.htm

[@sirwanjafeer7281]

Thanks

[@ADPTraining]

You're welcome.

[@indiahappynews5964]

ac drive ka digrame dikhao Sir plse

[@TV-zt1ly]

good

[@isuksamui]

เครืองคัมรีไฟไม่ออกเทียนเพราะคับ ทำเครือง

[@xiexianki1565]

EBD warning

[@bestinvestmentsinrizal3130]

5m70 6m70

[@ADPTraining]

Ok

[@tinkuhalder6716]

Apka namber doo plz

[@ADPTraining]

Ok go here... www.autodiagnosticsandpublishing.com/

[@Truongthohouse]

thanks