⛐ Check out our Garage to see what tools we use and recommend: www.amazon.com/shop/worldmechanics ⛐ Subscribe and hit the notification bell by the subscribe button for new videos: kzbin.info ⛐ Our GoFundme Page: www.gofundme.com/auto-repair-guys
@kwabenakarikari5962 жыл бұрын
I like this idea because it helps me a lot.i am vw specialist but due to this I able to work on every engine
@howiesiesoosoo4 жыл бұрын
Tip: Given that it is vital that no sealant gets into the 4 oil drain channels (behind the front camshaft oil seals) in the front camshaft bearing cross-member (into which the VVT solenoids fit) when sealing the cross-member as a whole, I have found that if you put some strong twine (string) in these oil drain channels when replacing it, wait until the sealant dries (24 hrs) then pull the string out, this ensures that these drain channels remain unblocked by sealant. The camshaft oil seals can be inserted carefully from the front afterwards.
@RashK1ng3 жыл бұрын
This is great!!! Also please do cylinder head removal video!
@rebelfromvaАй бұрын
How are you lining up the cam pulley back correctly on installation? Neither pulley is keyed and we can not get the car to start after engine swap and timing belt swap.
@johnCummins-v9i4 ай бұрын
Exceptional vedeo
@mehdidz41264 жыл бұрын
Verry Good informations My cruze 1.8L LT must change the ixhost camshaft i have a broken tooth.. Thank's for help
@edgarrmartinz4 жыл бұрын
same here lol smh, they make them so cheap now days
@NoBody-jo5rj2 жыл бұрын
same here i went to change seals for my chevy cruze exhaust camshaft and the mechanic broke one of its tooth
@faizelkhan2351 Жыл бұрын
I replaced head gasket only forgot to put on oil supply plastic cup that goes on top of the block
@andypustek1963 жыл бұрын
When I went to pull out the intake side VVT solenoid I broke the housing. Can that housing, which also houses upper half of cam shaft seals, be purchased separately?
@jwitt8271 Жыл бұрын
I am looking for this also
@jerrykinsey2220 Жыл бұрын
My 2011 1.8 curze has what I believe to be a lifter making noise. Before I take it apart how can I check to see which one is bad or has failed?
@mohdabd4594 жыл бұрын
What do u mean by we need new bolts when we put back together?
@howiesiesoosoo4 жыл бұрын
The 2 camshaft timing belt sprocket bolts are Torque To Yield bolts (as are cylinder head and other bolts and others in engines these days) that stretch to maintain tension. They often break if you try to use them again.
@ghostgaming72264 жыл бұрын
I need help man I have a 2013 chevy sonic I forgot which one is the intake cam and the exhaust cam how could I fine out?
@RGPinger Жыл бұрын
BECAUSE AT EXHAUST CAMSHAFT IS EXHAUST AND AT INTAKE IS INTAKE CAMSHAFT.. Logic
@jhonatanpalomar63702 жыл бұрын
É possível colocar um motor 1.4 turbo no cruze mais antigo 1.8? 2012 (Brasil)
Good day a can a broken impulse Transmitter sensor cause the car to read a diagnosis code P0366 On chev Cruze 1.6 engine as one of the teeth on the impluse sensor was broken from engineering
@shreda125hilux74 жыл бұрын
Hi man PLEASE HELP , I mixed up my camshafts :( how can I tell which one is the Exhaust and which one is the Intake camshaft? Is there a number or a letter? They look very similar.. :(
@ghostgaming72264 жыл бұрын
Did you fine out?
@shreda125hilux74 жыл бұрын
@@ghostgaming7226 haha yes!! I had photos before removing them and each one had a specific number/code which i used to identify each cam
@berniegrunhaus38992 жыл бұрын
@@shreda125hilux7 can you share the part numbers? i need to buy both camshafts because the previous mechanic lost them and now the customer wants me to solve this!
@shreda125hilux72 жыл бұрын
@@berniegrunhaus3899 sorry man this was a very long time ago and the photos I had were on a different phone which is not longer working , you can get the part numbers by simply calling your local dealer and giving them your chassis vin number of the car , they will tell you the part numbers for the cams
@berniegrunhaus38992 жыл бұрын
@@shreda125hilux7 thanks man
@victoriafausone734711 ай бұрын
QUESTON what is the Torque valve of the crankshaft pulley bolt?
@victoriafausone734711 ай бұрын
Value
@raymondking9313 Жыл бұрын
Were is A camshaft head or pmg located
@عليحسين-م8ه9ل4 жыл бұрын
Hello, please send me a video for the tuning of the Auto Center Aveo Drive US Model 2010