How To Set The Timing Correctly - Barina ¦ Cruze ¦ Astra ¦ Corsa 1.6 & 1.8 Engines

Link for timing tool kit (Australia) ebay.us/AmMPYA
Link for timing tool kit (UK) ebay.us/MhwSV5
Link for timing tool kit (USA) ebay.us/SUXzgD
In this video I show how to set up the timing correctly on a 1.6 litre & 1.8 litre engines in the following vehicles,
2007 - 2010 Holden Astra 1.8 i (AH)
2011 - Holden Barina 1.6 i (TM)
2012 - Holden Barina 1.6 i (TM)
2013 - 2016 Holden Cruze 1.6 Turbo (JH)
2009 - 2011 Chevrolet Cruze 1.8 (JG)
2011 - 2016 Holden Cruze 1.8 (JH)
2014 - Holden Trax 1.8 (TJ) SUV
2005 - 2009 Holden Viva 1.8 i (JF)
2012 - 2015 Opel Astra 1.6 Turbo (PJ)
2012 - 2013 Opel Corsa 1.6 Turbo
Opel Mokka
Vauxhall/Opel Astra-H (04-13) 1.4 1.6
Other Applications:
Vauxhall: Astra, Corsa, Insignia, Meriva, Signum, Vectra, Zafira
Chevrolet: Cruze, Orlando 1.4, 1.6, 1.8
Fiat: Croma 1.8 16V
Alfa Romeo: 159 with 939A4.000 engines
If I helped ya out? or just enjoy the content & you would like to buy me a drink ko-fi.com/gerardburke
Tool options that I recommend and use - www.amazon.co.uk/shop/gerardb...
➢ For business inquiries Email : [e-mail]
Disclaimer:
GerardBurke is a qualified motor technician who has completed modules & courses in manual handling and all aspects of workshop safety. These videos are not intended to be used by anyone who is not trained and or qualified to carry them out.
Due to factors beyond the control of GerardBurke, I cannot guarantee against improper use or unauthorized modifications of this information. GerardBurke assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. Use this information at your own risk. GerardBurke recommends safe practices when working on vehicles and or with tools seen or implied in this video. Due to factors beyond the control of GerardBurke, no information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. Any injury, damage, or loss that may result from improper use of these tools, equipment, or from the information contained in this video is the sole responsibility of the user and not GerardBurke.
Suitable for
Z18XER F16D4 F18D4 A16LET Ecotec Engines
#TimingSetup #HowTo #GM

[@GerardBurkeBurkesGarage]

All information related to makes/models and engine types are linked in the description along with the timing tools required. Thanks for watching.

[@Jimgrabber-ls6ci]

Explained more in a short period of time than others!

[@GerardBurkeBurkesGarage]

Thanks 🙌🙌🙏

[@steveveness3829]

Thank you, as a 3rd gen engineer following after a mechanic who did some interesting things with t belt replacement. Like not changing idler pulley because drive belt tensioner bolt is frozen. And didn't change water pump. ( both of which have failed hence I have it). I was certain timing was out, because of things you said, I know know my instincts were correct. Take my hat off to you. ( old time sign of respect from a time long gone). 43yrs trade life and 3rd gen engineer just had his hair saved from being pulled out by the roots. Sincere thanks😉🙂👍👍

[@lancelanphier9509]

I just went through this exact scenario in the last 2 days. I set the marks equal like a person would think with the dots lined up evenly and in the end after setting the tension on the belt the mark on the left intake sprocket would drop downward making them unequally lined up. I literally had to take the blocks out, loosen the intake sprocket and twist it one tooth and then I got the desired results that you're showing..... So my question is why in the heck did they design it like this and use that tool without instructions leaving the technician to believe that everything is supposed to line up equally??!

[@user-nk2zj6xy7d]

excellent video.. very clear and direct... a very much appreciated the close up zoom in.. very nicely main video

[@MrDyersy]

i always enjoy your videos mate.

[@GerardBurkeBurkesGarage]

Thanks Marty, I really appreciate tge feedback 🙏🙏

[@nicolemangan730]

Ty for the informative video

[@gemmanaughton3693]

Another great video♥️

[@cristi9944]

A very precise explanation, with clear images as usual, this means professionalism, to which I can add an extraordinary vocal timbre that demonstrates the safety of a well done thing. In the future if you can show the use of the oscilloscope in certain situations We can learn more about mechanics from you. Thank you very much.

[@GerardBurkeBurkesGarage]

Thank you Luca🙏

[@rhoadsfan]

Really.. he only showed that timing was out and helped sell the tool.. in no way did he show or even describe how to change the timing.. All he said was, “ linethe marks up” …how??

[@kennedysgarage3281]

Thanks Gerard 👍

[@GerardBurkeBurkesGarage]

👌👌🙏🙏

[@patkelly7999]

Good job Gerard, Thank You:):)

[@GerardBurkeBurkesGarage]

Cheers Pat 🍻🙏🙏

[@fixitrightmotors7547]

Thanks

[@arthurcator5246]

Great Video. I am about to do the timing belt on my 2012 Zafira 1.6. What I've noticed is that the timing marks on both camshafts don't line up as per yours. Is it possible the camshaft(s) have been replaced at some time and when front wheels have been put back incorrectly. At TDC do the cam lobes face into the engine or face out? Hope you can help.

[@diycarhome9151]

Very good video, how to time the engine.

[@lostsoul4591]

Hi have the exact problem is it ok turn exhaust sprocket by hand so timing plate tool sits in slot on back of shaft. Sorry for asking this but you didn’t explain what is involved in correcting position of camshaft being a bit out.I know that I should undo camshaft bolt and put timing mark on sprocket where it should be after so no problems in future. Thanks

[@bryandejarnette8394]

How do you fix the alignment of the camshaft do you gotta take the sprocket back off to let that locking bar slide in place easily

[@razvanturcu9871]

Just one question: On the surface that sits on the camsfaft, the camgears don't have a groove, so when replacing them, they can go in any position. In this case, are the 2 dots on the camgears that important, if the back of the cams line up?

[@qawwertyyugggyiuiuuhinkopo748]

I just want to leave a question on about the timing on them car when you put a locking device in the bottle by the transmission the murderer there's a little Rubber seal you got to pick out with like a hook ring screwdriver

[@drrobert2120]

Hi. Great video.. When you checked alignment marks. Did you make adjustment by loosening timing belt and just turning the one shaft to mate the indent to the tool? What was the failure code generated? Thanks

[@GerardBurkeBurkesGarage]

Thanks very much. It had no fault code stored, the adjustment of the timing was made on the camshaft adjusters (I removed the timing belt) The outer cap needs to be removed and then the camshaft adjuster sprocket can be moved once the bolt is loosed on the camshaft. (camshaft sprockets have no locating keyway on the cams) If you are just doing the timing belt it is very unlikely you will need to make any adjustments like that unless previously done incorrectly. Again thanks for watching, I appreciate the feedback.

[@drrobert2120]

Thanks..

[@mfamus2272]

Will I need to buy another valve cover?? Just replaced it last year 😕😑

[@zachaustin9126]

am trying to put the new timing belt on. I had the locking tool in place between the camshaft sprockets with marks for all three sprockets sitting where they needed to be. Upon attempting to slide the new belt on, I had the crankshaft sprocket on the bottom actually rotate clockwise about a 1/2 tooth. I am unable to simply rotate it back counterclockwise because the bolt is not a reverse thread and therefore doest grab going on that direction. What would you recommend at this point? I still have the top camshafts locked in place with their timing marks in the proper position.

[@pyromaniac354]

Use a rattle gun to put crank bolt back on temporary. Don't go to crazy with the rattle gun tho as you want it just tight enough so you can turn the motor backwards if need be like you needed

[@jamespennington7261]

Do you have to remove the serpentine belt to adjust the timing?

[@JonathanJimenez_metalriff6]

What is the process of lining up the camshafts with that metal straight tool … do I gotta remove sprockets and Some how turn the camshaft or something?

[@shanejohnston8670]

I have the same question.

[@martinj8547]

Question if I've replaced timing belt and water pump and put it back together a little bit out do you think that I might be able to rectify it by eyeing up the timing marks without taking of the tappet/camshaft cover and using the locking bar???

[@dmrftg6000]

I know comment was 8 months ago & you have probably sorted it out, but for other people reading the comments, no, the cam pulley’s & crank might line up & be in the correct position’s, but the cams can still be out because there is no key way’s on the cams! So you need the cams in the correct positions before you tighten the cam pulley’s!

[@shanejohnston8670]

How did you turn the cams to get them back in line?

[@TheNovianca]

I have the same issue how do I get it to align I can force the forward cam over and make it align and put the tool in but there's pressure forcing it back the other way

[@robertpriddy1808]

To fix this do i need to take the belt off and align all the marks ?

[@iankelly2110]

Yea I do a lot of of my work on opel I have the master timing kit if saves so much time and give you a peace of mind also. We'll done and on you for sharing. I am thinking of just specialising in 5 brands and keep it at that it's getting very expensive for all service data and wiring diagrams and back home hear in Ireland we are only 8 years from no more Diesel or Petrol engines allowed

[@GerardBurkeBurkesGarage]

Thanks Ian, much appreciated buddy. It's an expensive game to try an keep a pace with in so many areas and financially at times can be impossible. 5 brands is an interesting concept, I am sure you have given it plenty of thought. I will be more than likely attending some EV courses early to mid next year. I am pretty excited about that and getting hands on. It's never dull that's for sure :)

[@iankelly2110]

@@GerardBurkeBurkesGarage That's good to know I am on waiting list for RyansAutomitve For level 2 and 3 ev and hybrid can't wait

[@agussrodriguez608]

Whats the difference between the TK 1.6 AND1.6 TM engine?

[@mrtrader4628]

If it's not lining up, can I turn it by hand?

[@babyninjaonboard6191]

Hi you said what was the problem of the car?

[@marksewell3990]

Awesome video!!!

[@closertothetruth9209]

what an odd cam gear alignment, without that locking bar it would be an easy mistake

[@Lawrence-Joseph-Norse]

Repent to Jesus Christ! Are you a sinner? Luke 5:32 King James Version 32 I came not to call the righteous, but sinners to repentance. Luke 13:3 King James Version 3 I tell you, Nay: but, except ye repent, ye shall all likewise perish.

[@Lawrence-Joseph-Norse]

1 Corinthians 6:9-10 King James Version 9 Know ye not that the unrighteous shall not inherit the kingdom of God? Be not deceived: neither fornicators, nor idolaters, nor adulterers, nor effeminate, nor abusers of themselves with mankind, 10 Nor thieves, nor covetous, nor drunkards, nor revilers, nor extortioners, shall inherit the kingdom of God.

[@evander2086]

should the slots be horizontal anytime when i turn off the car? Or do I have to adjust something so that they stay in that position? thanks for your video bro

[@TheTank1664]

Spot on thank you very much. Fixed my problem. And am not a mechanic. 🫡👌

[@GerardBurkeBurkesGarage]

👍👍

[@preetsembhi1465]

Thanks