Can-am timing chain tensioner adjustment.

Get lots of questions about these things and how to re set the tension.
This is it explained.

[@20TAC]

Keep up the great vids. Lots of good information for those learning.

[@altermad]

Thanks a Million! Power is back.

[@831mach]

would that make a knocking sound like motor on its last?

[@FrankiesChannel]

Thanks, that was really easy. Does the piston have to be at top dead center, is it a must?

[@toddrichards3176]

Did you get any answer to that?

[@toddrichards3176]

Cool hope this fixes my knocking on my can am

[@toddrichards3176]

It did the trick stoped my knocking on can am outlander 1000xmr

[@toddrichards3176]

Problem came back and on my can am 1000 xmr you shouldn't do that because its hydrolic. Anyway my knocking is coming from my rods had it all checked out and these guys know what they are doing. Valves timing chain all good and it's not the clutches either.

[@grizzlyman239]

so you can reset it just by pulling that out and puting it back in?

[@robertkuntz2559]

grizzlyman239 stick it out and put it back in

[@a440able]

I'm looking for help, my cylinder head rear chain tensioner plunger popped itself out. Do I need TDC on the front to be able to re-insert? Zero room to turn the nut.

[@Mike-zn9xt]

thanks. very helpfully

[@mybudshoteyes]

Do you have line up the cam marks to do this? If I'm not taking the valve covers off?

[@donrostron1269]

I'd like to know that as well. I have a rough running engine that back fires on throttle close. I'm betting that it's the timing, I already changed spark plugs and they looked good.

[@mybudshoteyes]

@@donrostron1269 check your valves, i just adjusted them for the first time, ive had the bike since 13.

[@donrostron1269]

@@mybudshoteyes Did that help? I'm original owner 2007. Never adjusted them before. Bike has always been solid until now.

[@mybudshoteyes]

It did get rid of the tictic that developed, and less popping, she did start that......just a little bit, i would recommend doing both, since the valve covers come off to due the valves anywho.

[@Khaledx312]

Yes, it can be done to tighten it again, but be careful not to move or operate the vehicle while it is not tightened

[@903environment]

My 2021 cfmoto zforce 950sport something is making a loud ticking noise,took off valve cover n notice my chain is a little loose ,wat causing it to b a little loose

[@JD-xd3he]

? I accidentally popped off the tensioner when I was installing new starter. I put it back in would this cause my UTV not to start.it was running untill starter quit. Was new one was in it turned over great but won't start engine.

[@scodder37]

I have a 2005 can am bombardier 400 if the tensioner spring is messed up will it make it jump time

[@someguy6444]

do you have to take the top of the case off?

[@bmcnearney818]

My spring came out and the reason I noticed it is because of loud engine tick. I immediately took off plastics, the spring was sitting between the cylinder's. Am i in for a costly repair? I have the spring back in not sure if it is adjusted correctly. The engine runs and the ticking is not a bad but thinking it may be out of timing on a 570 2021 outlander.

[@toddhurley1237]

Gotta check mine tomorrow..2020 570 canam...ticking noise came on rite sudden..

[@rebeccaclements3243]

How do you change the timing chain? I have a 2003 bombardier 200 ralley and trying to figure out how to change the chain?

[@wildhorse192001]

Is this the same method on a 15 model 800? Not sure which engine this is in the video, thanks!

[@mzantow2000]

Thats funny winding the spring up eh?

[@CyprusAerialPhotography]

thanks, good enough that will come in handy

[@CotijaMen]

As cam hp increases with DROP-ins? the renegade 800R?

[@kundankumar-bl5ry]

my bike sound not good but hum new sound chahate hai kaise hoga

[@farukkhan903]

gama trax 4x4 timing chain replacement

[@andrew140672]

hey how offten do you have to do this ? do the rotax have many motor problems

[@rossboymanpig]

Tool flood