Can I Do A Diesel Swap, What Do I Need & What Will It Cost?

We've been getting these questions a lot lately: What will a diesel conversion cost, and can you do the diesel swap?
Why it's $10k:
6BT is ~$2000 + $1500 for basic rebuild (head, pistons, rings & bearings).
4BT is ~$3500 + $1500 for basic rebuild (head, pistons, rings & bearings).
Adapter plate, flywheel and starter is ~$2000.
Shift controller is ~$600. kit.com/debossg...
Alignment fluids, fittings, hoses, machining is ~$500.
DG shop rate is $65/hr at an estimate of 70 hours.
Don't forget shipping + taxes!
For more specific conversion part pricing & info, check out www.dieselconv...
Watch our builds: / @debossgarage
Never forget another measurement. tapeboss.com
Support us on Patreon. / debossgarage
Get some merch. shop.spreadshi...
Follow Rich on Twitter. / debossgarage
Follow Rich on Instagram. / debossgarage
Follow Rich on Facebook. / debossgarage
Follow Rich on Car Throttle. www.carthrottl...
*If the video was helpful, please give it a "thumbs up" and consider subscribing.*
"Travelin'" by SWIB ( / swib-1 ) CC BY-SA 3.0
NO WARRANTIES: All of the information provided in this video is provided "AS-IS" and with NO WARRANTIES. No express or implied warranties of any type, including for example implied warranties of merchantability or fitness for a particular purpose, are made with respect to the information, or any use of the information, in this video. DEBOSS GARAGE ("DG") makes no representations and extends no warranties of any type as to the accuracy or completeness of any information or content of this video.
DISCLAIMER OF LIABILITY: DG specifically DISCLAIMS LIABILITY FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES and assumes no responsibility or liability for any loss or damage suffered by any person as a result of the use or misuse of any of the information or content in this video. DG recommends safe practices when working with power tools, automotive lifts, lifting tools, jack stands, electrical equipment, blunt instruments, chemicals, lubricants, or any other tools or equipment seen or implied in this video. DG assumes or undertakes NO LIABILITY for any loss or damage suffered as a result of the use, misuse or reliance on the information and content of this video.
USE AT YOUR OWN RISK: This video is for informational purposes only. It is your responsibility to evaluate your own safety and physical condition, or that of your clients, and to independently determine whether to perform, use or adapt any of the information or content in this video. Any automotive repair and/or modification may result in injury. By voluntarily undertaking any task displayed in this video, you assume the risk of any resulting injury; your safety is the sole responsibility of the user and not DG.

[@DEBOSSGARAGE]

If you have swap related questions, best thing to do is join our Facebook group! It's a better platform for new questions and lots of experienced people there to help. facebook.com/groups/debossgarage

[@adamproctor6044]

I have been looking to swap a 12v or 4bt into my 2004 gas ram 2500 and can’t seem to find any videos or any real info on how to do the swap I don’t care about keeping stock gauges but I would like to keep my power windows and ac also does 10k include an engine and tranny or is it 10k+ the engine and tranny thanks for the good info you provide even if you don’t get back to me

[@MehdiKiawer]

how the emission going to work ?

[@leonardogalindez7933]

DEBOSS GARAGE how much to swap a cummins into a jeep

[@jacobsmart9583]

Like he says probably about 10k

[@dillonh321]

Should I do a R2.8 cummins or a 4bta 3.9 cummins? A 4bta is cheaper but doesnt have as much power.

[@A1soldiersaint]

I swapped my underwear this morning for a clean pair. It took a lot of hard work but I did it all myself and it cost less than $10k.

[@JohnDoe-mh8tm]

I doubt it was worth it. Maybe if you did it yourself.

[@scottchapman8044]

I did the same thing my girlfriend help me

[@Ybsjek]

🤣🤣🤣

[@jessebolles3661]

If u turn it inside out it will last u another 4 days lol

[@reed7562]

@@scottchapman8044 Such a virgin nobody’s falling for that.

[@bb_gunbandit4782]

Funny that I'm watching this considering I'm about to swap a John Deere 4045T into my 2005 F150. It's also getting a G56 manual and axles and suspension from an F350. Transmission and transfer case been freshly rebuilt, motor is brand new and has some extra parts to put some pep in her step, axles also rebuilt. Tearing the truck apart completely and rebuilding everything so every square inch of the truck will be in pristine condition.

[@johnnysanchez9031]

I like how you got right down to it without beating around the bush.10k ballpark is not bad at all especially if its going on a truck you plan on keeping for a while. This is the first video of yours I watch, but you have definitely gotten my attention. I am definitely subbing to your channel.

[@rogerelkins5206]

Can you do a series on doing a 12 valve cummins swap on a square body Chevy

[@maxwellmillette5759]

Yeah I second this, ive got a square body and ive tossed around the idea of that

[@keatonsmith793]

Plz do this this is what I’m wanting to do , 1986 square body Chevy and I want to put a 12 v in it

[@nash-xn1no]

do itttt

[@teebugg66]

I’ve got an 86 Chevy m1028 military truck I want to 12v swap I’ll let you borrow it if you need one to use in your videos! Lol

[@sostrucking]

There was a guy south of Iowa City is selling them at a decent price...not rebuilt that is. Not sure if he is anymore.

[@adamm4056]

Just wrapping up my 5.9 gas to 12 valve swap, total cost of the swap was around $4,500, including little odds and ends, engine crane, plywood, and the hundreds of hand warmers because of a Pennsylvania December.

[@austinatkins408]

Adam Moldovanyi how is it running a year later??

[@Kyle_Godfrey111]

Adam Moldovanyi update?

[@joshuakunze8930]

Yes I am also curious

[@campervanbug7658]

Labor costs and such

[@adamm4056]

5 years and 100k miles later it still runs and drives and has survived starting a family, from hauling firewood to 10k lbs of scrap. A few things here and there but nothing out of the ordinary and it wasn't hard at all. I was 18 in this comment^

[@717UT]

Thanks for sitting down and talking through the real world complications of this kind of project. I think almost anybody that's a car guy is hot and bothered over 4BT swaps. I sure am! But I know I'll never have the resources to accomplish it. But I love these videos and I love watching and learning. Who knows, maybe getting to see how it's done will help me learn down the road and do something cool too.

[@Gene4666]

Nice to see that there are still techs out there who have integrity.

[@SK-FarmAndRanch]

Totally understandable, great video, as a farmer in Alberta I put a 4BT in our 1984 Stackcruiser which has been excellent and (almost) trouble free since, and a 6BT in our 70's International tractor that we use for running augers and misc stuff here, thanks in part to your great videos. Thank you, warmest regards to you and yours.

[@jaigrazette9457]

really apresheate the honesty and realistic attitude of this channel

[@dakotahwest1]

JGMetal Jedi Appreciate*

[@SalandFindles]

+JGMetal Jedi Appreciate**

[@badboybootz8]

Lmaooooo

[@TheThotWhisperer]

6 years later but man I hope your spelling got better lol

[@tim2jz670]

I had a 97 f350 that I 12v swapped. I did the work myself. Total swap cost me about 5k like he said.

[@MrGLADIATOR5100]

I'm thinking of an 8.3 or 8.9 swap on my 93 f350.

[@someginger6996]

In all honesty, 10k isn't that bad to do a diesel swap.

[@AllPainNoGains]

I'm guessing it's probably more like 15 to 20 now with trumpenbidencovidflation.

[@enermaxstephens1051]

@@AllPainNoGains It's just biden printing money to give away. Trump did it a little, but over 90% less. Always look to dem commies to spend other people's money. Populists (trump) are generally against it.

[@Hoothie]

Exactly just bought an 08 f350 with a 5.🤮4 about to do a 12v swap have it repainted with new rims and tires basically a brand new truck under 25k

[@chrisethridge2348]

​@@Hoothie😂

[@hoseamatthews4527]

Hey Mr.Deboss so I Have a 98 K1500 5.7 Vortec Extended Cab 3 door Silverado I recently Purchased it from a older Gentleman who had bought it brand new and had fallen ill and needed the money. The engine and tranny are all original. He had kept it in tip top shape with Transmission Fluid Flushes and Filter changes every 35-40k miles and Oil changes every 2500 Miles Wix and Kn filters were his go too he cleaned it up and sprayed off the snow in the wintertime so there isn’t a single spot of rust on the fenders as most fall victim too aswell as the vehicle does not burn a single drop of oil and has had all the gaskets replaced routinely. My question is I’m looking at doing a 6.5 or 6.2 Detroit Diesel swap or possibly buying a baby duramax crate engine and or just installing a 6.6 or possibly even a 5.9 or smaller cummins engine into it I just would like to get your thoughts on it!

[@kennyv6135]

I did my 1978 f250 12 valve and Hell yeah! Its worth it almost 20 mpg instead of 9mpg. 10 grand is on the money give or take a few dollars. If you need a run down on a 78 or 79 let me know, Rock on!!!

[@rubenulloa6755]

what diesel engene fit on my jeep wrangletlr 2010?.

[@nickkoski7076]

i did a cummims conversion.. i made all the factory dodge parts... hoses,intercooler,radiator,ect ect.. think they where still in the doner... its the only way to go.. get a complete doner and make it work. for instance.. getting the intercooler to fit in my radiator support took 2 days to measure... think about it... measure again. then cut.. worked perfectly.

[@johnmarriage7246]

I swapped a 6.925 litre udfe6ta into a 1989 4x2 f250 used everything out of a 1997 coffee 88 truck motor clutch 6 speed box.been using it for 5 years everyday ,does hard work.super reliable. Most Japanese diesels red line at over 3000 rpm .pulls like a bull

[@onesecureone]

I'm about to do one in in a 1980 ramcharger wish me luck

[@omnipubgmobile1615]

How goes the swap?

[@lorenzovonmatterhorn4756]

Bro post a video of that ram charger

[@raffaeledimenza6167]

Update vid ?

[@brydonbrubacher5335]

Is it possible to swap a 4 cyl gas to 4 cyl diesel in a car? And do you know (in general) what typically needs swapped along with the engine?

[@253fabrication]

I subscribed later than most have.. I started watching when rich went to derrick (VGG) to install the fuel injection system in the bronco. I think I subscribed when rich was building the cab-over.

[@jamespallag8133]

Hello I put a 6354 perkins in a 1991 ford f350 made all the brackets myself did it in my backyard drove it 30,000.00 miles no problems

[@Tapped-o9k]

is putting a 6BT 12 valve engine into a mercedes s350 w140 worth it?

[@masonbelk5427]

I did a cab swap with a $200.00 tool set in my drive way. Set a 70 crew cab dodge onto a 99 Cummins

[@DanielFerreira-kc8ix]

I just picked up a complete 4bt with trans for 300

[@208RedNeck]

Daniel Ferreira lucky

[@ryanhaverkamp4404]

ill give you 1000

[@webchar]

they go for 4 grand where i live.

[@edlingja1]

Daniel Ferreira Don't buy a $300 combo you can buy a whole car for $500. Spend the money on a nice one with a warranty....

[@webchar]

u find me a truck with a cummins for 500 and ill buy it immediately

[@Superbayman94]

Always wanted to put a Cummins in my old 04 Honda Civic and have the turbo and whatever else just sticking out of hood. Sold the car because nobody here in Newfoundland where I’m at anyways can do something like you do

[@lanedj801]

It can also affect your weight so expect suspension or brake changes if your vehicles motor weighs less than your new one. Last thing you want is to hit the brakes and the vehicle dips the wrong way.

[@kodyhalo2]

I have a 1970 bronco and got myself an old grumman step van with a 4BT in it and have been dreaming of doing the swap for some time. it runs great and has been a nice moving shed lol. watching your videos has sparked that fire again... keep on doing what your doing man. i may have some questions for you if i can get the ball rolling.

[@OnlyTheEd]

Your main areas (probably) will be the electrical connections and the driveshaft changes/modification. (Please note Johnson's Gee-rage and "Todd Booke's Bronco swap).......His has the 4BT and a 5 speed (m5odr2, I think).....Jimmy (Johnson's Gee-rage) has a 1982 F150 4BT with the m5odr2....he's been building it for perhaps 2 years. His cash outlay has topped $6K, because he's had some issues and other modifications/ additions. He has done most of his own build except the driveshaft modification, and had help rebuilding the m5odr2. Otherwise, Rich is your man.....The $$$ I speak of is US, of course....Canadian is a different exchange rate. Oh yeah.....also the engine mounts/pads/whatever are going to cause grief.......And oil pan location, maybe....

[@dsam1398]

My 6.5 gave out (again) im gonna give it a shot swapping a cummins in my 95 silverado crew cab dually. Wish me luck.

[@samuelred4540]

Hope it works out

[@markjansen5674]

D sam Good luck! A video of how it turns out for you would be good entertainment for us folks.

[@Mebob2001]

a local guy here charges 15 grand to put a 12v/24v in place of a 6.0l psd, and 17.5+ for a CR 24v into a 6.0l/6.4l with a list of what parts he used on certian areas, not all, but he usally trys to use all the ford stuff, and very little cummins

[@shawnsimmons8268]

DEBOSS GARAGE if you EVER have a chance to do a 4bt swap into a Ranger, PLEASE do a video series. There are about 1.3 million Ranger owners that are currently lusting after a 4bt Ranger, lol!!!

[@MrBmore20]

Preach!

[@guyh.4553]

Thanks for calling it straight. Very rare in this day & age where it seems like everyone else is gloating over their work. This was helpful. Grease on the face didn t hurt as well! Ha ha ha ha

[@altaccout]

You need to consume better media if you feel that way.

[@skrewdreyever]

Thankyou! This is just what I have been looking for! I look forward to following along and learning as much as I can!

[@federicodenovi8862]

Just finished a 4bt swap in a bv 206 hagglunds with a 3 speed manual transmision.. made all the part my self including the shifter and linkage... very cheap swap!

[@Pinchegalloo]

How do you even make “parts”

[@SmudgyContent]

Hey wondering if I just got burnt… bought a 99 56block cummins nonrunning. I got the thing running but has a nasty knock. Looking for cracks yet to see any. Paid $1,000+ for the 12vcummins.

[@samanderws9333]

Hi I have a 02 golf stream Sun voyager RV and I want to put a 6.7 Cummins out of my 17 ram 3500 in it but I want wondering if it better if I put a 12v in instead

[@claybradley3442]

I got a 1994 ford f350 someone 12v cummins swapped and it's been a absolute nightmare. I currently can't get the altinator to charge. New altinator new battery just put in a transpo regulator still not charging. Wiring is a hack job on this truck. I don't know what wire to look for on the ford to tell the altinator to charge. I ran new battery cable to the altinator as well as a new ground I am at a loss

[@michael-shanehenderson8562]

I have a 4bt in my 1968 C20 and would like to add Vintage Air. Where can I find a compressor mount bracket?

[@mitchhouge8427]

honestly this channel is so professional for 8000 subscribera

[@1922DPenny]

Mitch Houge 407k, 2020

[@ukrarex]

500k apr 2021 Well deserved

[@JohnnyReyGonzalez]

519k June 29, 2021.

[@ThatOnePriest]

I want a 12v in my 2010 expedition running the 5.4 triton right now

[@evilal20]

Expeditions are damn near bulletproof. My grandma had one at 360k miles. My F150 with a 5.4, running at 290k

[@902isfake]

around how many diesel conversions do you do a year? and $65 an hour is not a bad price, a shop I worked at charged $105 an hour

[@DEBOSSGARAGE]

About 3 conversions a year but they aren't all diesel.

[@alanack67]

I just bought a truck with the engine I wanted ;) Id rather change a trac bar and steering box as opposed to re engineering a truck. Still 10grand seems like a hellva bargin to me.

[@edlingja1]

Well a hot-rod or race builder could just make a suspension system pretty quick if you strip everything and mount it on solid front/rear clips. It would be lifted as a car or truck tho.

[@markarmstrong3394]

$65 !! ??? Ya need at least $85 for overhead etc

[@okioki1131]

He owns the shop what overhead?

[@leifchurchill]

do a jeep cummins swap!

[@pointvillage16]

yes please!!!!!

[@killionairmen]

yes!!

[@TonyLing]

Nah, Perkins or a modern Merc

[@samuelgriffin8371]

Jeep liberty 4BT

[@chevymetrodriver]

Samuel Griffin i have a liberty lol

[@phildrye7143]

Do you think it possible to do a 12 valve Cummins swap in a 55 panel truck. Assume I would need the whole drive train and can the axels be made to fit the 55 frame?

[@justincook4069]

I would like to know what you would charge to put a 5.9 cummins in a 1995 1500 z71 with 3/4 front and back axles and the trans and transfer case

[@stanzingyaltson1280]

As I have cummins 4BT diesel engine 9.8 engine fitted on my truck. It is 1992 model, now I want to fit a power steering in my truck so please guide me. Can I fit it in the old engine? Please show me the point at the engine and confirm the rate for a second hand power steering assembly.

[@bryanfrancois4438]

Deboss garage I have a huge question I wanna drop a 6.7L Cummins with an Allison transmission in a 1993 Chevy S10 blazer would that be something you could work with

[@jonsnow9405]

I have a 1990 d350 12v I've ran into title issues. I just scored a 1965 Chevy C60 I'm trying to figure out what I need to do for wiring. I can make the engine crank and die.. what should I do about tach, water in fuel etc.. ? Is there any tips you can give me or video that might point me in the right direction? This is my first Cummins conversion. I can do gas burner conversion but 1st diesel conversion.. I have Dodge Manuel for diesel supplement just need pointed in right direction for now.. any in put would be greatly appreciated.

[@alexharris286]

Looking for a 12 valve for a 2005 f350 my 6.0 blew up again not putting a new one in ,

[@christopherproctor1662]

If you ever do a early 90's late 80's Toyota pickup swap please upload a video of it

[@killstrees]

I want to put a Toyota 1kzte in mine.

[@BottlecapDwarf]

Christopher Proctor i would to put a small Diesel engine in my Toyota

[@BottlecapDwarf]

*love

[@killstrees]

Unfortunately, these Toyota swaps aren't as plug and play as you would think, especially if it has electronics. I found that the wiring harness for the diesel is for a right hand drive truck, so it has to be rebuilt. Also, the gauges don't transfer either, from what I have found. Look up dieseltoys on forums. You will find pretty much everything you will need from those guys. I haven't done the swap yet, so I all I know is what I have read. I could be wrong though. I do know that you would be better off with a half cut which will have everything you will need.

[@donaldplank54]

I've done it it's a total b**** everything's easy but the wiring harness on the 1kz

[@smokey-mcpot-yr4ml]

I got a e350 6.0l 2006 van can u talk a little about the differences between the f-series trucks and e-series van diesels

[@JCo-zh1kx]

I don't have Facebook... So, what would you put in a 2016 challenger AWD?

[@williegohard1368]

What do you think of a Isuzu diesel swap for 2015 Nissan frontier King cab. I've been thinking about doing that. Like a small Isuzu diesel engine out of a small Isuzu box truck with the transmission as well

[@riccjaccson6876]

2018 Toyota Sequoia TRD Sport. Can I get a deisel motor without the def

[@JohnBraman413]

what's total cost to do a ford ranger swap including exhaust? how long does it take for the swap? can truck be dropped off at the shop and picked up when done?

[@jamisonkemp859]

I would really like to know if a 6.2l diesel is worth it. I really want to because it's affordable and one of the easier things to swap in to a square body. I just don't know if it is worth doing. I know they are gutless and have average torque. Also is NA or turbo better for the 6.2. or start with an NA and make it turbo.

[@OnlyTheEd]

I am impressed. So much so, that I hit the "subscribe" button. Thank you for explaining a lot....

[@chadvarble3565]

Deboss garage can I put a Cummins in a Silverado 1500 gas truck ?

[@GeloNegron]

Lol, I wanna buy a Titan XD for the low with some minor issues, fix it and swap a 6.7 Cummins or 5.9 Cummins into it and do custom Wide Body kit.

[@louisbabycos106]

Would love to swap a 2LUZ turbo diesel from the Cruze into a Suzuki SX4 AWD hatch .

[@garycook3612]

Love your channel and am a subscriber. Always look forward to what Frankenstein you're building. I'm about to start a Bt6 in an 04 crew cab that has a Duramax. The motor went down after 296k miles and I'm not replacing that. Already have the Cummins block machined and ready to go forward. Only new the adapter plate and rebuild kit. Gonna lean on your videos pretty hard for the conversion brackets and hopefully make my own videos of the hurdles as well as the triumphs. Thanks again and looking forward to your next vid!

[@DEBOSSGARAGE]

Thanks. Feel free to ask anything you are having trouble with and send me the links to the videos as soon as they are up!

[@garycook3612]

Thank you, sir! Will do

[@MonkeeJack]

1965 ford vanette . Nothing like it . It's all aluminum. Ford straight 6..250. engine. 4 speed. I want to convert it to a diesel and automatic. Can it be done ? The floor come out. It looks sorta like a old milk truck delivery or postal . But it's a R.V. 😀

[@GrizzlyDonBauer777]

How much will you charge to 6bt cummins swap . With a 48 Re transmission 1988 dodge Dakota and have it rolling

[@SlyC00p3r]

If i swap a cummins into my super duty can i keep it automatic?

[@brettferguson69]

add a allison transmission

[@dopeyiniraq]

I've been searching to do a Cummins swap in my 2015 gmc sierra 3500 it's gas 😔 can you help me find the parts I'd need to get the motor in I want to swap the 6l90 for an Allison also

[@karlajanethmartineztabares3097]

Una pregunta hice una conversación, le puse un motor 12 válvulas cuminns a una camioneta que traía un 24 válvulas como le ago para que marquen los marcadores

[@DoesUrBeanHang]

I got a 1958 ford custom 300 want a diesel swap, idk what would be the best to swap or how much

[@deadlydavem]

I found a 15k mile diesel pusher motor home. It's an Allison/Cummins combo. Anyone know if the engine and transmission can be retrofitted into a front engine truck? I'm looking at installing them into a 1953 chevy 2 1/2 ton truck.

[@crashnburn3980]

I met a guy one day that was driver I tracker or a sidekick can't remember, he had a 4 cylinder diesel engine in it. He told me it came out of a tugboat

[@mikeallensonntag]

So that 10g is for labor and fabricating and the small swap essentials. Every thing like big parts, engine all that is additional either customer provided or you source it I'm assuming for cost plus little on top?

[@seanm5240]

I have a square body 74 blazer where are you guys located I would love to do a diesel swap for the 12 valve

[@clydemontero4523]

How much would it cost to swap engine on a two thousand excursion gas to diesel with an allison transmission

[@woowoozie]

What the best manual cummins With the most horsepower to put in your 6.4 power stroke doing a swap

[@Jursaw]

You should do more videos on working on a cummins engine, maintenance stuff.

[@andresbidrogo914]

Buddy I got a 2000 F350 V10😔 is amazing truck of my grand Pha … but I wanna make a swap for a 6.7L or 7.3… can you do that for me ?

[@lilysmith7810]

The 8.1 in the 03 is getting some major miles on it, close to 200k miles, not kilos. Been thinking about doing the swap because the 8.1 doesn't have much after market support for goodies. I would like to keep the Allison, but not sure about mounting it to the cummins, if it fits or someone makes an adapter for it, it's a bitch'n trany.

[@ronaldreed7698]

Lily Smith those 8.1's work well in boats.

[@turbodiesel4709]

Lily Smith : The GM gas 8.1L is/was a terrible fuel pig. A Cummins turbo diesel 5.9L or 6.7L would be a huge improvement, and worthwhile swap so long as the truck is still decent. Keeping the Allison is not that difficult, you'll just have to get a machine shop fabricate an adapter plate for the bell housing. Seems like there may also be something available from the medium-duty truck market, but I don't know for sure.

[@96cr]

Lily Smith they make stroker kits for the 8.1

[@steveriley1000]

I have a plasma cutter and a welder I can make my own brackets lol , I would love to put a 4bt in my 2012 Tacoma 6 spd

[@Demonlord468]

I have not question about my capability to do so my only question, is a 2005 1500 with a 4.7L original gasser 2WD worth the effort to swap or should I save this type of swap for my 2004 5.7L 4x4 for later on when that becomes an option and do something else with the 2005? Another reason i ask is the more i look at the two trucks the more i think that the 4x4 is going to cause WAY more issues with a Cummins swap than on the 4.7L 2WD idea. I was originally wanting to do a 5.7L conversion from the 4.7L so i never have the issues I've run into with those twice now but, talking to people and looking at the difference between the two under the hood is nearly as much work almost from just looking at it. Or am i wrong and the 5.7L hemi conversion a better idea? Thanks in advance.

[@wickedvendetta102]

I’m planning on dropping a Nissan TD27 2.7 diesel into a 1983 Dodge Ram 50 (mini truck) could you give me a few pointers, the engine should mate up pretty well, I’m just concerned about how to wire it all up.

[@deliciousgixxer3670]

How does one hire you? I got a 5.9 in a school bus i need built, runs perfectly fine but id sure like to smile at the fact id have a 500 hp 900 tourge bus

[@TheJared1445]

Hey Mr. Deboss what is the possibility of swapping a Cummins into a 2008 Durango AWD. It currently has a 5.7 Hemi

[@DEBOSSGARAGE]

Anythings possible. It only costs time and money!

[@2JZLS]

some guy stuffed a duramax in a 2010 camaro, and a 6bt in a 06 charger and RX-8. i saw a 4bt 240x on youtube, wouldnt doubt if a 6bt fit

[@Flydevice1]

The main question is are they legal, if I start anything I want to know if it’s hard to get the trucks street legal with swapped engines.

[@scottchapman8044]

@@Flydevice1 anything's legal if you don't get caught!!!!!!

[@ronaldreed7698]

How much to do a swap into a 99 ram 1500, would it be cheaper because no need to fabricate so many parts if any at all? Not trying to low ball you just listening to the number of items you had to fab.

[@Mike2077f]

Gotta make a blueprint for 5.9 or 6.7 cummins swap into any 6.4 powerstroke

[@ericfrancia29]

How do you wire the swap is it hand done wire by wire???

[@FarDrizzz]

I have a 73 f250 camper special, what transmission do i need if i put a 12 or 24 v in it

[@munemrabadi809]

good content, I have a 2004, f250 powerstroke 6.0. it has 350k miles. I did a head gasket at 310k miles and ran great for 40k miles. at the present time it needs another head gasket job. lower end is fine and has great power. I'm thinking of rebuilding the entire engine. I can't find genuine ford pistons and don't want aftermarket pistons. how wise is it to use the same pistons with 350k miles on them? thanks

[@southreaper75]

Is it possible to put one in a military humvee... I don't know how reliable the diesel engine in the humvee is... I just know that the Cummings engine is reliable.

[@theboostedboogieman95]

Question I have a f250 2005 I blew a rod years ago it's just been sitting with 35k on it lol but I wanna swap it I have a f350 diesel everything for it also its from a ambulance so I have a everthing is it possible and if so would it be cheaper to just take the body off the ambulance front and cab and put this cab and bed on the ambulance Frame ?

[@johndenelsbeck8075]

I am looking into doing a swap in my 93 f250, take out the 351w and put in a Cummins 6bt or 4bt. Was just wondering if I need to change out fuel tanks and lines what. Thanks

[@Turbo-wj9qc]

Just drain the tank and it will be good.

[@-ouv]

Had a few 99 24v, and I got a 08 mega cab 6.7 Cummins and blew the 68 towing so got a nv5600 out of a 01 cab and chassis truck, bigger input shaft and I swapped that. I also got a 2003 2500 4 door short bed but it's a hemi and gets 6 mpg sith premium. I'm thinking of swapping that with a 12v and nv4500 or nv5600

[@1bad335i]

Do you have to change the ownership from Gas to Diesel ?

[@jefferypatterson2732]

I would like to do a conversion on my 2012 sprinter I want to put a Cummins on my dodge 3500 diesel on it. Can you do that conversion

[@christufts5286]

Where would one begin to look for a donor Cummins to replace a 2010 6.4? I just put $4,000 worth of work in to my truck hoping that it would fix my regens every hundred km's and within 150kms of a new DPF, it did a regen on me again. Not the regular "drive to clean filter" followed by "cleaning exhaust filter" for the duration but instead just flashed "cleaning exhaust filter for a moment" but started using fuel like a pig and it was confirmed by the superheated exhaust when I parked it. Also discovered that 4 and 8 have slightly low compression. Not sure what to expect or plan, but I don't have any money in to the engine itself yet. It was suggested that I have the PCM flashed to see if it stops unnecessary regens but I'm starting to look at worst case scenarios and backup plans. A Cummins seems to be the better of the expensive routes...

[@DEBOSSGARAGE]

Wreckers, Kijiji, or craigs list. I have a 94 12V P-pump that just rolled into my driveway that is for sale. 250 000 km on it.

[@christufts5286]

That being said, can a pre-08 engine go in to a newer truck and meet the emissions standard? Not sure if the e-test is based on engine year or truck model year.

[@DEBOSSGARAGE]

Truck model but it varies by weight. Under 3800 kilos is a visual (believe it or not) in Ontario, If its over, you can go for a heavy duty test (which is $145) but then it can be done as heavy duty. Putting a diesel in something that used to be gas, has to pass the odb.

[@jayaicholtz]

@deboss garage I would love to see a video where you review the Cummins r2.8

[@DEBOSSGARAGE]

Looks like its going to happen in the next couple months

[@jayaicholtz]

@@DEBOSSGARAGE can't wait.

[@NOMADNEWSTV]

I seriously want you to do the 6bt swap in my CamperVan at some point..I also want to do a 4x4 conversation I’m hoping I can get both done for $15K. I’m selling my Harley-Davison and Land Rover to Fiance it.

[@Nostradamus_Order33]

Questions 1) 6.4 PSD transmission needs what type of bell housing, SAE____?

[@tuckerfinnicum3949]

I'm only 17 but I'm hoping I can get the money to do something like this, I have the engine but I just need literally everything for the swap, I plan on swapping a 1996 f350 crew cab, the engine is a 24v with the p pump conversion the person that used it before me had used it for compotition pulling, what's been said is that it has 900 hp and I don't remember the torque numbers but I'm hoping to be able to put an Allison automatic behind the Cummins and I'm mechanically inclined to work on vehicles but I don't know what I'm going to be running into with this, would it be cheaper for me just to make my own mounts like you said? Or for a first time swapping anything buy all the components and mounts ect ect and just bolt everything on without risking the quality of my own mounts failing? I also don't have the slightest idea how to tune a transmission but Im sure their is a forum for just about anything on how to do it, I also have people in the town I live in who build transmissions and tune them for 1000hp mud pickups, I'm literally open to all the advice in the world for this lol, it'd be my dream to have this pickup with a Cummins engine

[@bigcubanc3880]

How much will you charge me to remove engine and tranny from my motorhome 5.9 and allison . Into my 1998 chevy silverado dually nomotor in there now. You can keep motorhome or ill take it

[@tomhession5207]

Ok im swapping the chassis of my 97 ram 5.9cummins and it was a salt truck lots of rott and I was just wondering if there is anything I could do to help with this project and I never did this before but I'm going through it and I don't know why I am doing it with no time to do it and I am doing it right now but I am not in a good place right now because of the legal reasons why I need to know how fast I can get my truck back to work and I was just wondering if there is anything you can think of about this project

[@PSR1791]

What about a 2wd to a 4wd swap on a 5.9 manual???

[@SuperDuty250]

Is it possible to swap a 6.4 powerstroke with a 5.4 liter?

[@spoof6862]

To pick your brain, or anyone else who might know, will a 7.3l powerstroke fit in a 1991 ford pickup? Also, are there any electrical components that will need to be added or modified when doing this swap from a 460?

[@danielober884]

Is it possible to fit a 5.9 12 valve into a 1959 Chevrolet Apache ?