Unfortunately the people who don't understand the testing, they will thumb down. The reason for that a human has a nature that it opposes anything strange for it or to the matter one don't understand. I could say only sorry to them!
@TheQazi19477 жыл бұрын
hi when you testing the car ignition is on or off ? and do you can you use multimeter ?
@abdelkaderkatalan54157 жыл бұрын
we didn't see how the baord was connected to power some missings let us confused.
@gantulga81567 жыл бұрын
Hello, please could uplaod on your youtube page for 2006 toyota corolla/XLI/ manual transmission model and serial number for me. Engine is 2NZ-F, it has automatic transmission. I'm still looking for it. thank you
@JoeCnNd6 жыл бұрын
Yeah, no thumbs down needed. Great work, where did you get the diagram for your vehicle test points? I'm having an anti theft lock out and would love to get my checks right with my pico. it happen from jumping another car.
@rennardclarkee83736 жыл бұрын
Sir I have problem with my Nissan Tiida CVT 2012 a Air Condition guy fixed my AC and did not rap a wire properly in the engine this result in a grounds that burnt the Ac wire to the fuse box and make the car turn over but not start I took it to a technician where he changed the engine harness however he said I had to get a new ECU for the vehicle what could be the most common issue caused to have the car not start also wat could be issue inside the ECU to be damage and is it fixable ?
@tbbainter7779 жыл бұрын
Thank you for such helpful videos.Without circuit diagram how did you determine or identify circuit test points and what readings are correct? Thanks for taking the time and sharing your knowledge.
@JahanZeb19769 жыл бұрын
tbbainter777 Dear friend schematic diagrams are impossible to obtain for such systems. You can just determine the test points and expect voltage levels and frequencies by your experience and understanding. Regards,
@oldskoolfunk719 жыл бұрын
Great info! How do we get information on PCM/ECM test points?
@Shark-ye1yj6 жыл бұрын
Good explanation of ECU hardware and testing at this channel (Saud Automation).
@gamuchiraitsokodayi41678 жыл бұрын
this is good stuff. thank u. i have a nissan micra k12 with no spark no fuel injection and no codes when scanned. the ecm looks quite similar to that one you are showing. please tell me which one is the IC for fuel injection and spark on mine.
@mrnitin27497 жыл бұрын
very well explained sir....nice to see someone using oscilloscope for testing...😊
@JahanZeb19767 жыл бұрын
Thanks dear subscriber. I am frequently using scope for testing.
@train49053 жыл бұрын
A superb video sir.well presented,
@love2wheel10 жыл бұрын
Awesome video! How did you get the circuit diagram of ECU? I am looking for circuit diagram for ECU for 2002 Pathfinder. BTW, do you have any video to check the circuit of Immobilizer? That would be absolutely wonderful, if you could open up an immobilizer as well. After watching your videos and some research I understand how these components talk to each other. In fact, I just bought an oscilloscope. ;) Thanks.
@JahanZeb197610 жыл бұрын
Param S Dear friend ECU diagrams are not available to average diy like me or you! But you can test them using some techniques like one I showed here in this video. On immobilizer I have a video on Nissan Sunny immu testing and it is here on my channel. you can watch it. Also don't forget to subscribe on my channel if not yet subscribed. Regards, kzbin.info/www/bejne/qHu5fKlrmLmhj5o
@akshayacharyarockstar9 жыл бұрын
Good evening sir, what you have shown here is very informative, do you have ny idea on making an ECU TEST Bench !!!!
@JahanZeb19769 жыл бұрын
+akshay acharya Thanks dear friend for nice comment. That is a good idea to make a test bench full of necessary test equipment but for me big problem is money. I can't offer big money for such a job. Regards,
@leftofsanity7 жыл бұрын
Thank You. Very basic question for you. I live on the East Coast of the USA. I am a beginner electronics repairman looking to make a business out of not just PC/Mac board repair. What tools/info would I need to get into Vehicle "ECM/PCM" repair? How would I test them?
@JahanZeb19767 жыл бұрын
The key for their repair is your knowledge then second is the ECU emulator. They are expensive but very useful. Also you will need other tools like Oscilloscope, multimeter, soldering iron, hot air station, screw drivers, hex torx and other tools etc. Also you need a database of information.
@qwkz63899 жыл бұрын
your doing a good job don't worry about other peoples stupidity very informative
@JahanZeb19769 жыл бұрын
+Wize one Thanks friend for liking. You are right idiots are everywhere but I am not worrying them. When ever such bullshits are coming on my channel, I am simply blocking them from any stupid comments. Regards,
@qwkz63899 жыл бұрын
haha i think that is best thing my friend i have a question for you if you have the time to answer you seem very knowledgeable about ecu components if that is the right terminology i have a motorbike i don't ride much and the battery gets disconnected but i must enter a pin every time i re connect i was thinking if i erase the immobilizer eeprom programming will i have to bother with this security system anymore will my motorbike operate correctly just minus the security? or if i reprogram the eeprom i am just learning about this in my own time thank you very much please get back to me at your earliest convenience
@Airman..6 жыл бұрын
Hello Could you make a video explaining how an ecm/ecu exactly works? Starting from mcu, ic, transistors etc Thx
@JahanZeb19766 жыл бұрын
Dear friend if I may get some business in this field, I will sure shoot videos to satisfy your needs. Stay tuned.
@clustermaster84564 жыл бұрын
Hi, great video, thx for sharing. Please advise where can I buy ECU circuit diagrams?
@heatherrhodge25884 жыл бұрын
You can get the pin identifications in the vehicle service manual. In my cars service manual I was able to find the voltages that should be at each pin..you could Google "name of your car", don't forget to add whether it's automatic or manual "ECU pinout" & you might get lucky. If not search for your cars service manual..there are physical books for purchase & electronic versions. I think mine had this info in the "relay and control modules info" section
@luisb.henaoj921610 жыл бұрын
Hi ,, very good and helpfull ivideo, but I wnat to know how to get the electronic drawings, for Nissan computer and also for other brand names. best regards.. Luis Henao.
@JahanZeb197610 жыл бұрын
Thank you very much dear sir for subscription, liking and sharing video. May your couple always happy! Very nice to see both of you! ECU drawings are something a secrete of trade and companies are never sharing. Only there are some third party equipment who are providing help to figure out and repair such ECUs. Other thing to do is to collect chips data used and then try to trouble shoot such ecus. You have been come to proper place on my channel as you are Electronics enthusiast as I understood. I would upload tons of videos on all aspects of life. Regards,
@mtrltoolman9 жыл бұрын
thanks for sharing this video . i hope you can make a video about oscilloscope how to use and what for .
@JahanZeb19769 жыл бұрын
toolman talal Thank you very much dear friend Talal for understanding and liking the video. Sure I would shoot a video on Scope. Scope is something very useful and a bit confused test equipment. This is basic and a must used equipment. Regards,
@mtrltoolman9 жыл бұрын
LearningZone thank you
@saaedibrahim60859 жыл бұрын
you are a genius my friend i want your help for my Nissan sunny 2003 after I fix idle sensor I did relearning for it ,,,.relearning is go good but if I switch off the car ,,,the car go bad again,,,does ecu have small battery for memory like computer
@JahanZeb19769 жыл бұрын
+saaed ibrahim No dear friend there is no battery instead the information you are storing is stored on a flash memory. Unfortunately there are such problems occurred sometimes as you stated due to bad design of the equipment design. You can overcome them by using different techniques and options. Try to compensate your idle air by mechanical adjustment if the electronic calibration may not help. Regards,
@Airman..8 жыл бұрын
good job, where can i get the PCB diagram? or is it just a pure technical expertise
@JahanZeb19768 жыл бұрын
PCB or schematics diagrams are not available. This is companies secrete. This is a matter of testing and sure experience and skill. Regards,
@322doug7 жыл бұрын
well i like the video... thanks for posting. BUT where can i find the spec sheet for , test point voltages , for a particular car??
@JahanZeb19767 жыл бұрын
Such an information is very rear available on the internet. You can only rely on your own knowledge of repairing and understanding of electronics to do such a job. Regards,
@ejazkhan21476 жыл бұрын
sir thank you so much for uploading videos
@bhoyetsplading53387 жыл бұрын
its ok idea.. if the 5volt ref is low voltages or short to batt.what is maybe the cause,?
@simonnyamutekenya21546 жыл бұрын
Thanks people for such information. Anyone to help me with information I'm repairing an ecu for Isuzu diesel bukkie 2.5l dteq 2014 model. I want to see a component that was burnt beyond recognision. I want a clear picture of the inside of the ecu
@waeiltobgy53019 жыл бұрын
perfect work man , i really learned from your video thanks alot
@JahanZeb19768 жыл бұрын
+Waeil Tobgy That is great if you learned something.
@arnaudlecomte438110 жыл бұрын
Merci ! That is thank you for this insightful tutorial !
@JahanZeb197610 жыл бұрын
Arnaud Lecomte Thanks for nice comment dear friend. Nice that you subscribed and you will get notification on each upload. Regards,
@dragan32905 жыл бұрын
I need to try this on my Toyota hilux Australian version can i use a digital storage oscilloscope or is multimeter better? Any reply appreciated 😊
@JahanZeb19765 жыл бұрын
Great to see your comment. Scope and volt meter are same in nature. You can use any. But using scope is better if you have one that it will show you waveform also. Wish you good luck with your troubleshooting.
@Airman..7 жыл бұрын
Excellent video thx for sharing
@JahanZeb19767 жыл бұрын
Thank you very much dear friend for liking. Must subscribe the channel so that you may get more and more electronics videos.
@saudashraf87468 жыл бұрын
thanku soo much sir for helping me out i appreciate and inshahAllah i hope to get good result. thank you again
@piomad60228 жыл бұрын
hello , i have ecu from ford c max , on mc33186dh 1 on leg for cp i have 25 volt , can u tell me what to check ? the trottle body do not have power
@richardrockwall88796 жыл бұрын
thank you very much for your time
@JahanZeb19766 жыл бұрын
You most welcome dear friend.
@afaqprince9697 жыл бұрын
sir pcm aur ecm mn kya farq hai..pcm engin k sath hota h. aur ecm under the vehicle?? righg
@JahanZeb19767 жыл бұрын
Dono aik hi cheez kay do nam hen. koi farq nahi.
@MrCarzonekit9 жыл бұрын
Thank you
@ventureelect7 жыл бұрын
Great video, keep em coming.
@JahanZeb19767 жыл бұрын
Stay tuned, I will upload so frequently. Better if you subscribe my channel to be in contact always. Regards,
@nfranks0537 жыл бұрын
tpms module repair
@MAbid-zt7nm7 жыл бұрын
sir i had a ford explorer 2008 problem is rough idle at stop. i check the voltage at the electronic throttle body input two wire connector it 3.7 v at both wires will it fine ? or should be 5 volts and the seccond thing is the voltage should present both wires? kindly give ur suggestion thank u
@JahanZeb19767 жыл бұрын
Thanks for subscribing on my channel. Subscribe if not yet subscribed! Voltage may be fine but the throttle bodies are accumulating dust and debris. You should clean that for nice performance and good idle. You should watch a few of my throttle body cleaning videos on my channel to understand the subject. Also there is one or two videos focusing on drive by wire throttle body cleaning. You will know how to clean them and set up the idle to a nice value. Please don't hesitate to ask anything anytime. Regards,
@munyadesmond49584 жыл бұрын
please how many current entered there and how to test it
@michellamarche16588 жыл бұрын
allo i was wondering what voltage i am suppose to read on the last pin that you check because i got the same ecu from a 2005 sentra and giving me allot of trouble thank you your video is really helpful .
@JahanZeb19767 жыл бұрын
That is great if it helped you. Regards,
@saudashraf87468 жыл бұрын
Sir as i have been watching your videos n it helps me alot. But now i am in prob with my nissan Pathfinder 2003 as it cranks it starts but it has acceleration prob.however machanic says its ecu prob and i have repaired it 3 time nd it gives me same prob every 5 to 6 days Pls help me out if its ecu prob what should i do
@JahanZeb19768 жыл бұрын
If you are repairing one ECU and that is giving you same problem repeatedly, it means the repair is not successful or the ECU circuit went overloaded. In such a situation a very perfect and extensive repair of the circuit is required or otherwise you can replace the whole ecu with another one. On the other hand if the problem is repeating with another replaced ecu, there seems to be some problem with your throttle body. Try replacing that one. Regards,
@saudashraf87468 жыл бұрын
Thanku soo much sir . you gave me all your precious time. I hope your suggestion ll help me inshahAllah
@MrMasterapu7 жыл бұрын
Sir I want to buying car diagnosis but Which is the best brand I din,t know.u can help me
@JahanZeb19767 жыл бұрын
Verus Snap on. but very expensive. the other alternative could be a cheaper Chinese one.
@MrMasterapu7 жыл бұрын
Sir launch products r not good?like this x431/IV/v.
@vamsikaranam23537 жыл бұрын
hii sir, this is krishna and i completed my undergraduation with mechanical and now i am intrested to learn how to repairecar ECM and emoblaizer keys would you help me about that...thanking you
@JahanZeb19767 жыл бұрын
How can I help you?
@richardrockwall88796 жыл бұрын
here in the states you cant find inside diagrams of control units. is there somewhere you recommend
@JahanZeb19766 жыл бұрын
Yes dear friend the internal diagram is not available anywhere. This is their secrete. But one can repair it by experience and understanding.
@m3akku17 жыл бұрын
Hi, I would like learn ECU chip level repairing, where is the best place for it?
@JahanZeb19767 жыл бұрын
Your own knowledge and experience is the only best resource available. There is no such material available on the internet to get any help from. Regards,
@zx8401ztv10 жыл бұрын
For accurate dc voltage measurement i tend to use a digital multimeter, oscilliscopes tend not to be too accurate, i seem to remember 3%. Also your multimeters resistance is typically 10million ohms so it would not affect delicate circuits, im waffling again ha ha :-))
@JahanZeb197610 жыл бұрын
Yes you are correct. Multimeter are great to test for DC voltages and rms ac quantities. But problem is sometimes you are checking waveforms and intermittent behaviors so you are using oscilloscope then it is handy to use oscilloscope as a multimeter to test both AC and DC.
@yosimoran75846 жыл бұрын
where it would be possible to availa comprehensive book regarding ecu testing and repair
@JahanZeb19766 жыл бұрын
If I may write one!
@sssttt65339 жыл бұрын
good video
@JahanZeb19769 жыл бұрын
+Sss Ttt Thanks.
@saudashraf87468 жыл бұрын
Asalamualikum Sir i have 1 more prob if can help me out. i really appriciate all your answers. Problem is that when my pathfinder 2003 is on last quarter of petrol it automatically turn off engine then i have to start it again .and it happen around 3 to 4 times untill i refill the petrol.i m not sure if its fuel pump prob. I m really scared that maybe it ll give me a new prob please help me out
@JahanZeb19768 жыл бұрын
Dear friend thanks for appreciation. It seems like a fuel pump or maybe a fuel filter also if you didn't replace it ever. So better first replace fuel filter and then fuel pump if needed. Although it could be proved by testing also. I have video doing such testing on my Toyota Corolla. Regards,
@stevenjames70737 жыл бұрын
thank u for sharing ..
@JahanZeb19767 жыл бұрын
Thank you very much dear friend for liking. Stay tuned for future videos. Regards,
@peterfrancis38652 жыл бұрын
Nice
@AshokSingh-jr9en7 жыл бұрын
hello sir. please help me. I am having Maruti Ritz car and there is a problem that the fuel pump is not working and also a ligh of heater is not blinks. Mechanic said that there is a problem in ur ECM because it is not providing current to Fuel pump. can u pleaee tell me what is exact problem and if there is problem in ECM then how to repairs. please help me sir
@JahanZeb19767 жыл бұрын
Dear friend this needs further investigation. Sometimes there is no problem with the ECU but some problem external to ECU like in wiring, relay or some control module which drives your fuel pump. All is needed to carefully check all the system before attempting to replace the ECU as it is an expensive part. Also if it is petrol car, ask your mechanic to put petrol from the outside or provide propane to the engine and let it start. If it starts and runs on external fuel source, they should make some arrangement for fuel pump external to ECU. In this way you will be saved from an expensive replacement or repair. Or on the other hand if car doesn't start and runs on external fuel and everything is ok outside the ECU, you will need to repair the unit or to replace it with another good ECU. Sometimes it could be due to immobilizer security problem if it is immobilizer equipped car. There are a few more videos on immobilizer and security on my channel. You may watch them and get some idea. Let me know when you may do the above with your car. Wish you good luck with your car repair.
@AshokSingh-jr9en7 жыл бұрын
thanx sir. I want to provide some more information that my car is having a diesel engine. Mechanic check fuel pump directly by giving power to it then it works and starts to eject fuel but car is not able to start because injectors are also not working at that time. But now mechanic is saying that injectors are now working there is a problem in the wiring which is now fixed but fuel pump is not working right now.
@JahanZeb19767 жыл бұрын
So then it should be easy. If the injectors are working and the car is start with external power to fuel pump, it is an easy task to make a keyed power to the pump then. It will save your big money compared to ECU repair or replacement. Regards,
@babayanjuadetunji16278 жыл бұрын
Hi man am having problem with my Honda accord ecu the ect sensor did not have the 5v reference the car only start when dead cold and reading the volt without the ect it's showing 0.036v
@JahanZeb19768 жыл бұрын
Seems internal voltage regulator went bad. You can use some other arrangement to create such working voltage. Means use some external voltage regulator. Or the perfect solution could be the repair of the ECU if you have enough electronics knowledge. Wish you good luck with your repair. Regards,
@sssttt65339 жыл бұрын
I see that the values of the voltages appear intermit . Aren't they dc ?
@JahanZeb19768 жыл бұрын
Some are DC some are chopped DC!
@sssttt65338 жыл бұрын
What do you mean
@AshokSingh-jr9en7 жыл бұрын
hello sir please tell me that if i change my car ECM unit than it is must to change the car lock set also
@JahanZeb19767 жыл бұрын
+Ashok Singh it is needed to marry the new or replacement ECU to the car. Sometimes it need reprogramming or ECU refreshing and some tomes sure key and lock cylinder replacement. This depends on your auto lock smith abilities and facilities. Good lock smith can reprogram it for you. Soon I may add an article to my blogspot on this subject. Stay tuned.
@AshokSingh-jr9en7 жыл бұрын
ok sir thankyou
@soulmasterdw8 жыл бұрын
if you want to understand wat video about...... go microchip mcu sign up and look at there car ecu designs then figure out things like shift bit registers etc
@AshokSingh-jr9en7 жыл бұрын
sir please tell me, In this case Is there any possibility of problem in ECM unit.
@JahanZeb19767 жыл бұрын
You mean if you make any arrangement for fuel pump to run then it could cause any problem to ECU? Then the answer is there will be no problem to ECU at all if one may do it carefully and may not touch the ECU wiring in such modification. Such modification would a perfect solution in your case. If anything else, you most welcome to question. Regards,
@AshokSingh-jr9en7 жыл бұрын
Sir i m saying that in this case the fuel pump is not working then it is due to some problem in ECM unit or there should be some other problem. I mean that there is possibility that the ECM is defective
@JahanZeb19767 жыл бұрын
It could be a defective ECU or could be problem somewhere outside the ECU. It needs proper investigation. Anyhow the external keyed power to the fuel pump should solve your problem. Regards,
@AshokSingh-jr9en7 жыл бұрын
ok sir thank you very much. I appreciate ur work u r providing very useful information to us. thnx
@AshokSingh-jr9en7 жыл бұрын
hello sir now in my car fuel pump and injectors both the things are not working. please tell me how to solve this, mechanic is unable to solve this problem.
@carelectricautomobiles97065 жыл бұрын
Thanks
@asaamv7 жыл бұрын
have nissan micra 2012 march petrol i am having problem with my car , central lockig system from the driver side door not working . front wiper is working but rear wiper is not working . headlight working and brake light also working but turn signal not working and trunk door not locking. and all doors not working electric
@JahanZeb19767 жыл бұрын
It could be a bad fuse or wiring problem. Seems there will be some +12V supply rail missing to certain section. Check first for blown fuse and then check for wiring. For fuse testing refer my other videos on my channel. Thanks for linking and subscribing.
@asaamv7 жыл бұрын
it was a loose connection on the front
@lakoyaross99438 жыл бұрын
i have a 20MHZ Oscope will that work.
@JahanZeb19767 жыл бұрын
Sure it may work if you know how to use it properly.
@ejazkhan21476 жыл бұрын
sir wonderful me tire thank you
@train49053 жыл бұрын
Steve from the uk.
@richardrockwall88796 жыл бұрын
Where do you get the pin out charts for ecu?
@JahanZeb19766 жыл бұрын
A vehicle schematic diagram may help you.
@elnathanhijmering3389 жыл бұрын
do you repair Hyundai Accent CRDi 2006 ECU?
@JahanZeb19767 жыл бұрын
I repair almost every thing!
@elnathanhijmering3387 жыл бұрын
hi, can you send me an address so I can send the ECU for repair?
@EndofUSA8 жыл бұрын
so for each test point, what does it all mean?
@JahanZeb19768 жыл бұрын
+EndofUSA I can't understand your question.
@EndofUSA8 жыл бұрын
LearningZone by testing each test point what are you looking for and what does the oscilloscope say for each graph?
@JahanZeb19768 жыл бұрын
+EndofUSA That is explained in the video. Oscilloscope is a graphic voltmeter. A video soon will be upload on use and benefits of oscilloscope.
@christianrobertadzic93218 жыл бұрын
Hi! I'm also interested what that signals on that TP are for? Each TP is describen in a service diagram and the must have value are also described there. I respect this video and I'm not a hater. I just interested to figure out your technic how your are make a decision which signal on that TP is ok and which is not. Actually, a signal can have more parameters than voltage high. So, how you know if you get pwm signal or only a jumping 5v signal because something is wrong in the circuit and the signal looks like similar as a pwm type? I actually a bit confused with this explanation: here is 5v, here is 12v here is square wave or whatever, without to have the parameters of the exactly TP...
@user-sm8wo3dj5z6 жыл бұрын
is that water on the board?
@JahanZeb19766 жыл бұрын
+Jose Ferreira possible, if you are happy with that!
@user-sm8wo3dj5z6 жыл бұрын
LearningZone or is it flux? I am not criticizing
@JahanZeb19766 жыл бұрын
No dear friend. This is flux and some plastic risen for protection.
@sheilashay38657 жыл бұрын
do you own your own company?
@JahanZeb19767 жыл бұрын
Not yet dear friend but am looking forward to have one in future.
@muazamali51224 жыл бұрын
Assalam.O.Allakum..sir Agar ya he video ap urdu m banaadoo......to ....boht help ho gii
@JahanZeb19764 жыл бұрын
Ye you are right. You may visit my other channel and must sub this and that one. There everything is in Urdu. Search on KZbin my channel The Engineer
@muazamali51224 жыл бұрын
Ok thanks...😊
@carslover35099 жыл бұрын
use ova m to test dc ?
@JahanZeb19769 жыл бұрын
+amjad amj Yes can be used but that time i was dealing both with waveform and DC so I used oscilloscope for DC as well as a voltmeter.
@Eeropolvasti8 жыл бұрын
Good Job, you are genius !!! Don't worry some stupid loser's comment,....they are jealous of your knowledge, only freaking thing they can do, is a bad hangover =)) So, I am having a problem with my ECM/ infiniti FX45/2004, AC works sometimes, sometimes not, freon level is OK, and compressor works??, and engine smokes a lot, could have issue also with piston rings..., and valve stem gasgest,...BUT, could faulty ECM also change valve timing, and be a reason for extra smoke in engine??? I only have 120000 miles, power is not great, but is OK, and there is no noise in engine?? Drinks oil like crazy, 1/2 a quart/ day???? How could I test my ECM, before I buy a new one, they are so, so expensive =((( If I send it to you, how much you charge to test/ fix it??? Be reasonable, buddy;o) Well done, youtheman =)
@usmanmehar92156 жыл бұрын
how mach procedure ecu or pcm testing Pakistan RS
@JahanZeb19766 жыл бұрын
It needs big range of equipment to repair ECU. It needs something 10 lak rupees to invest in tools and equipment for such job.
@imrannazeer86 жыл бұрын
Bahi aap pakistan say ho aap urdu me samjao ta kay hame be kuch samajh aye aap enghlish me samja rahe ho angreez ko sub pata hy
@soulmasterdw8 жыл бұрын
if u want a decent test bench u want to get into mcu programming and making digital emulators for all different car parts...... then u can simulate alot of engines pretty essay run ecu on bench XD
@JahanZeb19768 жыл бұрын
Where to get one and for how much?
@autohome62597 жыл бұрын
Salaam sir kya hal hai please apna contact no de saudia ka tu hai liken aap pakistan chly gy hai jahazeeb bhi pakistan ka mobile no moje send kar de
@sameexc5 жыл бұрын
Sir I have some query regarding Corolla 2003 ECU.. it will be great if you could provide me your email-id or another source of communication to have a chat with you...
@muazamali51224 жыл бұрын
English m to pahle he boht videos hia urdu m bnaee plz
@JahanZeb19764 жыл бұрын
Must visit my other channel also. The Engineer Simply search on KZbin.
@Shuaibshauibansari5 жыл бұрын
Hindi
@JahanZeb19765 жыл бұрын
Friend I have another channel which is particular Urdu and Hindi. You may sub here and there. Search on KZbin. The Engineer
@michael66927 жыл бұрын
me no understand ,,, me human
@JahanZeb19767 жыл бұрын
No worries. Be a good human then you may be understand.
@diytech4u4 жыл бұрын
ENGLISH ?
@JahanZeb19764 жыл бұрын
Yes, any problem?
@franklopez28468 жыл бұрын
This is so stupid. Not everyone has this device.
@JahanZeb19768 жыл бұрын
What do you think if somebody have no basic test equipment available then someone is showing a good and reliable testing technique, is doing stupidity? If you are thinking in the same way then you are an enemy of knowledge. You need a to broader your mind and try to get some basic test equipment if you are interested to do such kind of work. Otherwise there is no need to put your leg in such critical work. Regards,
@abdoudfi82057 жыл бұрын
Thank u
@JahanZeb19767 жыл бұрын
You most welcome dear friend. You may subscribe to have automatic notification on each upload.
@abdoudfi82057 жыл бұрын
I have participated in the channel, and thank you very much and I hope that we have learned more about ways examination.Ecu 😊😊😊