Car Fender repair rust & paint at home Diy

Just Launched the Website: mad-4-motors.com/
Step by step guide on how to repair rust at home with little cost.
East diy job you can do on your own car with great results!
How to paint your hood complete guide: • How to Paint Your Car ...
Products used:
Clearcoat aerosol- amzn.to/2ANeEUJ
Primer Aersosol- amzn.to/2DctNR7
Sandpaper assortment- amzn.to/2RSrcUg
Masking Tape- amzn.to/2RLsZuy
Tack cloth- amzn.to/2RK60jv
Body Filler Bondo amzn.to/2Mai48q
Bumper scuff damage I repaired and paint video here! • How to remove Paint Sc...
Facebook- / mad4motors
Disclaimer:
Due to factors beyond the control of Mad4Motors, it cannot guarantee against unauthorized modifications of this information, or improper use of this information. Mad4Motors assumes no liability for any property or personal damage that may arise from doing a repair on your vehicle after watching any of my repair video's. Due to factors beyond the control of Mad4Motors, no information contained in this video shall create any express or implied warranty or guarantee of any particular result. Again Any injury, damage or loss that may result from improper use of tools, equipment, or the information contained in this video is the sole responsibility of the user and not Mad4Motors.

[@Mad4Motors_]

Bumper scuff damage paint and repair video here! kzbin.info/www/bejne/n5LQi3-qndGZfZI

[@hotrodhotrod-wc3bu]

Mad4Motors ive never seen a professional auto repair shop use csn spray paint .

[@R-Mc]

I have rust on fender on my 2000 Chevy Astro what's the steps for me to do I sand it down. To the bare metal but in the middle it's soft a little but when I feel behind the fender it's no hole or nothing but it's under even now do I need Bondo or what I don't know never did this before

[@johnydoe7065]

Mad4Motors do you need to buff it after it fully cures about 2-3 weeks....?

[@monmixer]

rattle can master, my buddy built a basic motorcycle based on a wide glide, he had about 6 grand in it. rattle can painted the tins with Wal Marts best. It was sharp. looked like a nice customized wide glide with an S & S motor. sold it for 12 k. thanks, some people make it look like brain science.

[@leannabroad5538]

@@R-Mc 12m, 2

[@michaelhenriks9405]

Having done the same type of repair, I would like to share some advice: - Use an acidic rust neutralizer to get rid of the rust you couldn't sand off - Use a zinc protector spray before applying the filler (the filler is full of water) - Do not wet sand the body filler - Do not sand down the whole part to clear coat it, try to keep the repainted area small - After a week of so wet sand the whole piece with a 2000 sand paper then polish (the paint color will then be uniform)

[@JouniKyyronen-nv1ep]

Michael Henriks yes filler and water no good

[@amyjmj3]

Only thing i don't agree is not to wet sand the body filler...

[@michaelhenriks9405]

Aaron Hudson water in the body filler will not only make the metal rust but also crack overtime. Your choice

[@sf4756]

I think that's what I did wrong when repairing rust spots in my 2010 F150. I sanded it down Bondo primed wet sanded to get smoother finish painted and clear coat. for someone who's not a profession that came out pretty well looking!!! until 6 months later rust start the show through! now it's about a year later and it's getting worse. I wasn't sure what I did wrong but now I think I do.

[@robertoleeva985]

Michael Henriks. Hey thanks for your input. I'm getting ready to do some work and will definitely refer to your suggestions.

[@582ChevelleSS]

This is a great cheap and cheerful repair for a car that you are trying to get another year or two out of.

[@davefilms345]

This video saved me 900 quid. I done this sort of thing simular to my car. Ok it's not as good as this but it looks 90% better than it did before. Thanks so much

[@jeffwatson151]

YOU JUST SAVED MY LIFE THANKS! good job looks nice better than paying someone hundreds of $ to do it when you can do it yourself

[@joebmxx]

Great video for a quick temporary fix but a few things. 1. Always treat the bare metal with a rust inhibitor or zinc primer. 2. Your better of just spray the whole panel evenly with base coat to stop the blending showing through the laquer. 3. Once the laquer has hardened after 48hrs 1500grit wet and dry it till it's eggshell then bring back the shine with cutting compound & a polisher, it will come out like glass.

[@swektmaico]

The rust will be back sooner than later because it's not near gone. It's evened out, flattened and painted over. And the painting with both color and clear coat should be applied with large movements from off of the part and over it all and out again in a steady motion. Never small movements pressing and letting off the nozzle while directed onto what you're painting. The big problem here is usually the back side of the rust since the pores usually goes right through. I have found motorcycle chain grease in spray to be quite good in sealing existing rust and keeping it from growing. The inside should be cleaned with a steel brush or something to get the bare metal/rust exposed. Then sprayed with grease. And after some while maybe a spray with a rust protector keeping the grease from drying or getting washed off.

[@bendude6748]

You can get a ready painted new wing/fender for £95 delivered here in the UK ( not sure how much that is in USD ) but to me it’s just not worth bothering by the time you’ve bought the paint/bondo etc you’ve spent half as much if not more than a new one

[@ad-dajjal7133]

Good effort at home..But, you should remove all the rust first inside and outside ie remove the arch liner at least to do this.You have not removed any exterior parts and eventually the paint will flake from these areas.You have filled over the rust and have also used water over bare metal and filler that is porous.An acid etch before primer will also help to keep the rust at bay. You did an fantastic job with the tools at hand and have given many people really good knowledge on what you did,keep up the good work .

[@tonygreen9883]

So a tiny bit of rust, in the end you did the whole wing that will stand out like a sore thumb

[@jerryp2433]

No body shop will warranty rust repairs. You can spend thousands and have the rust still come back...This is a good video for people who don't want to spend $$$ at a body shop and still have the rust come back. I've done that before and it sucks.

[@bludclone]

I think people in hell are forced to do car rust touch ups for eternity.

[@howardlake6178]

I hope you're getting paid fairly by KZbin, because you sir are a legend. Another brilliant video 😀

[@minar0x]

You’re only error was making it look better than the rest of the panels. Ahahahhaah Thank you, time to take me rusty new van to the shop.

[@minar0x]

Your* Auto correct always makes the error

[@jonjon9047]

Rust treatment and primer prior to filler. Don’t use any water until you flat your final coat otherwise you risk trapping moisture and causing further corrosion. Don’t mask panel lines on the same plane - blend.

[@crappiehookking387]

He did pretty good I'm just going to half ass my shit to stop the rust from putting holes in my fenders then paint it with spray paint

[@Mrsaintanger01]

Why sand down the entire fender and not just the area that needed work? Going to be trying this on my yoke soon so just curious

[@Opsnews365]

Ok guys tips please so if I hand sand the rust off my fenders and wheel wells then use some body filler sand it will that work as quick dui

[@TVBASICINFO]

Haha..., all the dislikes are from car body repar shops...😅😅. Good job.., tuppa da mornin to be troo to be troo 👍👍

[@Mad4Motors_]

😅Thanks!

[@fanatic3856]

Definitely You tube is for people like you !!! Your video materials are helpful and very good.

[@deaklaszlo6749]

Nagyon fasza lett.Most gyorsan add el mert pár nap mulva átüt újra a rozsda

[@jamesatty8595]

@Mad4Motors how long did it hold? Thank you for your clear and informative videos.

[@freddubose5539]

Looks better than really good. It's a professional diy job,I'd a thought it went to a shop!

[@Mad4Motors_]

Thanks 😊

[@kurthuck2630]

Nice job! Have done this in past, only problem even with the "rust stop" over rust within a month it will bubble from behind fender. Loosing battle, nice to do if selling car right after doing it.

[@Mad4Motors_]

True ideal if you selling or use the same process on a new fender

[@ryans413]

You make it look so easy but I can try on my car gotta touch up and area that got scraped against a pole above back passenger wheel well. My only issue is trying to find my cars colour match I got sand paper got the clear coat just need to find the base coat that matches

[@jorgebolivar9300]

Thank you for sharing,I feel more confident cause my problem is somewhat what you are showing .

[@andrewpaton6075]

thank you my friend you've saved me a fortune !

[@vitorvieira9853]

👏👏👏 good job! I have a problem in my like that.... So, your video give corage to fix mine!!! 😁

[@Mad4Motors_]

You can do it!

[@bobbaker430]

This video saved me a lot of money...thanks

[@robinbodak3076]

Enjoyed that but is there any hope for a vw polo 56 wheel arch! ...wish be luck..cheers

[@DungDang-gc9jf]

Please let me know what part I need to buy for this job ?

[@mikemillie3826]

Can you tell me instructions what spray you use step by step if you tell me

[@miroslavstuler814]

Hello guys, i was following step by step, but painted color is much darker like car color and it is obvious. Of course i bought color by the original code, but i think car color is lighter cause car is old and sun work hard. How to deal with it? Thank you for your advices.

[@frankgengstae9301]

Hello, how long this repair lasted? I'm planning to do something like this on my car.

[@Mad4Motors_]

I have more up to date videos on the topic they might be more helpful

[@karloskarlos5146]

Pěkná prasárnička. Vždyť ten blatník musel bejt orezlej i zevnitř. Za pár týdnů ta rez pěkně zase přeleze na ten venek.

[@milescockerill2104]

could you use a rust remover gel such as jenolite and normal sand paper instead of using a flat disc sander?

[@Aslan98-e5v]

You used Kac number sandpaper thanks

[@sapkane]

what a result , top , got a 2 inch knock on my wheel arch i think i tackle it after whatching this , thanks

[@raulaleman8132]

use green fiberglass in the can its waterproof it will last longer than bondo but put the fiberglass first then bondo for the fine finish

[@dragosdraghia2662]

can you tell me, please what sizes did you use for the emery ?! I didn't remember very well from the video. I can also wipe it with kitchen towels if I don't have one. 

[@jensen1971x]

Wheel arch rust comes from the back side. Washing the mud and salt from the inside lip of all the fenders frequently will prevent this kind of rust from even starting.

[@cnman9743]

What did you use for rust treatment?

[@tombob671]

Quick, tidy and thrifty job! 👍👍 Greetings from Oklahoma

[@nicksahl391]

what about to bottom edge, and inside the wheel well at that spot, wont it just rust from the edge and the back? did u sand the under part and fill that too??

[@Mad4Motors_]

Hi yes sorry I didn't video it

[@nicksahl391]

did u do the entire wheel well, or? im about toe fix almost the same exact thing on my nissan. im going to try it myself for first time so any other tips or a follow up video would be greatly appreciated . if i sand the outside and bottom edge, how to i stop the rust on the back and to where it meets the new paint? just rust convert the wheel well and let the paint line meet the converter? sorry i have a lot of questions i just dont want to mess up. prime and clear coat the rust converter on the inside????

[@w.farioli1576]

Clean up both sides of the panel from rust, then apply some phosphoric acid and let it for 24 -48 hours. After that you can put on some filler primer and paint. After that coat the back of the panel with some grease or oil. That should stop the rust for quite a bit, especially if you put some oil regularly.

[@mattm5786]

Should’ve sanded the rust down a lot more and even some good metal. This rust will come back fairly soon

[@mwc66]

Yes was just thinking the same thing . Also on a rust repair like this , the inside of the wing would need treated and filled to stop it rusting from from behind as that did not look like just surface rust, A quick fix that, that is all it is. Would be good for about 2 weeks, especially here in the UK

[@theforestlizard223]

@@mwc66 Did the same repair on my mercedes and after 3 years it still looks good and i do live in a country where they salt the roads like crazy

[@Gramkan]

Yep, such a half assed job

[@lamuerte60106]

So you guys watch this video for the only purpose to talk shit to this guys work?

[@mattm5786]

@@lamuerte60106 no I watched the video because it’s satisfying to see it be done righr

[@prettypaws3115]

Oh my gossssssh!!! That is sooooo amazzzzing!! I hope I can find the colour code to my Nissan. What a great job!! Thanks for sharing! 😊

[@ciprianionutapetroaie7314]

I can use it on the hood of the front car, I also have a blue Volkswagen Passat b5 and I bought 1 car spray extreme automotive petrol resistant lacquer super smooth protection for oil and petrol

[@autoturismo3269]

Rust and paint DIY with Connor mcgregor.

[@Fishnfreak]

What a minty comment lmfao

[@thedailyshorts3728]

😂😂😂😂

[@lahummer5759]

Conna Mccloud of the Clan Mcloud

[@ditizogaj6592]

how long time take from step 1 to finish ? how many hour will be all done ?

[@aliyoussef8201]

Is it possible to get that wheel arch cut out and have a fabricated one welded in? Cuz mine is really bad

[@MrAzHofi]

rust remover/converter must be used before the filler

[@andrewmcgowan8440]

am needing to do the same myself, that was the dogs, so many experts out there, but looks a fantastic fix to tide you over.

[@_Common_Logic_]

Do yourself a HUGE favor and forget what you just saw... There are plenty of good uploads (some are even by professional painters) showing the average guy how to get a nearly professional job at home with rattle cans, on a budget... This is NOT one of those videos. Not trying to be a dick here, but it sucks to waste time and money if you don't have much of either. Good luck.

[@disordersanjeev666]

Will this process be completed in a day ?

[@denniswoodgate3905]

Going to do mi e over this weekend but need to find the same colour as my car transport cy green 🤔🤔

[@szuben6664]

Już wolał bym kupić używany w kolorze błotnik i wymienić za chwilę dalej rdza wylezie i wogole jak to wygląda

[@eddylorenzo5033]

What was ur rust treatment ?

[@UnulOarecare]

Really inspiring - how can I feel up the holes in the fender if you know?!?

[@werdlyfe9577]

Use Bondo.

[@UnulOarecare]

​@@werdlyfe9577 found something in the end - too late though as that fender is completely gone now - Bondo doesn't exist in my country

[@libinjmathew6854]

Hi, can anyone share the link of this spray paint, so that I can purchase online. This video help.me a lot but I couldn't get this product anywhere..please Platinum colour

[@Montahue]

What about the the inside of the fender arch, it seems you did not even look at that?

[@heangheang-garage]

Khmer Cambodia can do very nice

[@Mad4Motors_]

? dont understand

[@girtsreders6987]

Thank u for this video now im inspired to do my rust issues by my self

[@bmwfan2814]

Good results. Cheers.

[@Mad4Motors_]

Thanks 👍

[@mragrippasibongiseninene4182]

Thanks, it wise . But i just need to know more about the red stuff used on your mixture.

[@ajsmalaisemopargarage2073]

That's just bodyfill hardener

[@lingamsrikanth296]

hello what is the color code of spray can you have used

[@kissgabor2996]

2 nap és újra rozsdás le. Ez igazi taknyolás.

[@demoncustoms4014]

Good job bro 👋👍

[@jemmace2586]

great job! now to do the rest of the car, that's the best panel on it now!

[@jemmace2586]

or then..

[@dsmchick935]

Yeah I'm a student of auto body collision repair I'm trying to learn rust repair thanks for this video it's helpful

[@valentinomustac3548]

Dont learn from this 😂😂😂

[@lilianbaycost2846]

incredible job- thanks

[@tjkim382]

i tried it something like this n rust came back. I didnt use primer is that y?

[@josephribot2261]

Very good teacher you are!!

[@SF_Curious]

You basically can apply clear over sanded paint? As you did?

[@skyguy1988]

i have a 2004 audi a6 and the front passenger fender has a rust spot. I took it to somebody and they said i had to replace the whole fender....but i say bullshit because it's not even that big of a spot. is he trying to rip me off? or can i do it myself at home

[@costym.2328]

Este foarte bine prezentat dar nu imi dau seama ce spray -uri folositi , a_ti putea să-mi spui si mie, Succes si multumesc.

[@jocalibusohump]

Good method of work 😎😎😎

[@andersdakin1610]

Good job 👍 I did the same great 👍 you do this so the rust won’t spread :)

[@Mr61grod]

Rust never sleeps

[@ksingh5407]

Yep, sound job, it will sell on a rainy day.

[@jeremyb2108]

Better be some heavy rain

[@nddavi58]

conor mcgregor working as a mechanic now i see 🤣

[@PaddleDogC5]

Good for next day sale!

[@pinkfloyd8361]

Yup....... That's about all it's good for. That absolute bodge would be ok for about 6 months "tops". It's a superb fast bodge, respect in that regard, but not a lasting fix.

[@robertgrlic6505]

@@pinkfloyd8361 why do you say only good for 6 months? Can you elaborate on what is missing ?

[@lewisbrown51]

What is he on about?

[@gavinmcvey8177]

That's bright the rest of it needs done it's a 20year old car looks a different shade of gold on the wing probably needs a polish to fade it in but good job on the cheap cheers mate saved me a fortune but my wing's are coming off the car and inside the arch is getting done aswell to last as long as the out side then back on to finish the filler n paint n polish after with good quality polish with very very fine grit 😎😎😎

[@wordtruth6116]

What products did you use for stopping the future rust?

[@harryaldieny7697]

rust in peace

[@joktomok]

Vulkanudbrud Pro

[@jacky_1472]

countdown to extinction

[@Groaznic]

Rust in piece... Polaris.

[@masterflow6783]

Awesome, all I need to do now is take it to a panel beater.

[@gabgamer8111]

Wats the name of the colour gold or somthing els ....plz tell me the exact colour coz i too hav the same colour car but cnt find the exact colour from near shops..

[@kwikmechanic6844]

Great videos Mad4Motors 👍🏼

[@krisraps]

i have black car from 2006 and i need to do this thing, crazy how good it really looks

[@virginiasubadallrecipes7720]

How would call that white mug you put in to dry please

[@RichardOutdoors]

Fantastic. Appreciate this excellent guide. Please can you tell me what grit flappy disc you used in the grinder?

[@billconserva1461]

I see lots of these Home repairs, haven't seen one yet that I bet won't be rusting again in 2 years.

[@oscar-sp1ei]

How can i get the same color of my car..?

[@PreetSingh-ji7ey]

Thanks connor

[@homergee57]

Who did the Translate for you ?

[@waynedunne4838]

Hi mad4motors i decided to try a similar thing on my focus mk2, didnt come out as well as i thought, still yet to polish but hoping ive put enough clearcoat on, i couldnt get the original shape back but better than it looked before haha

[@qaisniazi3793]

Colour is looking different?

[@smarte.r.1450]

Well done mate. Nice tips there and for the novice with a runabout this is more than fine!! Good eddort

[@anwarmuhammad7304]

Good job Some time paint shop people make money more then car price .

[@josephjoseph1981]

Exactly what I need to keep myself busy these days . Thank you sir .

[@joserivera-vs7kw]

Good job 👏

[@manil0pez492]

Bien trabajo amigo te felicito gracias x mostrarnos tu trabago

[@CattleRustlerOCN]

Desafortunadamente su trabajo no es corecto. Uno o dos meses y él tiene que hacer de nuevo

[@darkshadowsx5949]

the rust on my fender is beyond a simple body filler job.. :( how much do you think it would cost to fill up a pool with vinegar and let my car soak in it? how much car would i have left? I'd probably loose 10% in weight if it took all the rust off.

[@hassannasser338]

Sand most of the rust off or use a metal wire brush. If the rust is under the car, spray rust reformer and then bed liner. It should cost around 50 bucks.

[@lolaottinger6976]

Wish you could come over and repair some paint on mine.