Carb leaking fuel? Here's how to diagnose the problem...

[@Abaddon5850]

You are the first ive found with a legit solution instead of saying just get a new carb.

[@billjones7817]

Thank you for making this video. Prior to watching this, I had searched and searched to find what was causing my leaky carb. I followed the directions of all the other videos out there and only replaced the needle valve... still leaked! I knew nothing of this o-ring problem until your video. Fixed the problem and saved so much frustration. Just for context, I have used youtube to teach me many many DIY things over the years, yet this is the first time I have ever left a comment... hopefully that demonstrates my level of gratitude... thank you for taking the time to teach the rest of us.

[@drjoefoste]

Outstanding video. This gentleman has superb knowledge of his trade and has the ability to explain problems with carburators and how to repair them with precise and concise explanations. Thank you for your time sir.

[@jthan258]

Same here

[@philpeel5235]

Well done Andy. Shows you can learn every day. I am 75 years old! Thanks mate. Peely

[@T3_forge]

Thank you so much, as an old retired Army instructor you’re spot on. A life goal is to rebuild my 1993 KLX 650, you’ve got me headed in the right direction. Cheers!

[@AndyMechanic]

Thanks Jason, appreciate your feedback. Good luck with the rebuild. Cheers Andy

[@marinob7433]

very analytical! thank you Andy! 5 years after the first release of this video and its a masterclass!

[@sidfindley767]

Looked all over the web and didn't find the answers I was looking for. The verification methods you used to determine if it was working before re-installing were spot on. That was what I was missing. Had this carb on and off the quad a dozen times and not once was it any better until I saw your approach. Previously... every time I re-installed the carb the fuel ran right through the overflow tube time and time again. I will take these lessons learned and apply to all my carb issues in the future with complete confidence!!!

[@AndyMechanic]

Thanks Sid, pleased to be of help. All the best. Andy

[@mrblueskynm3968]

Wow, this is exactly the issue I just had after rebuilding the carburetor on a Yamaha TTR230. I didn't replace the float seat because it was too tight with the new o-ring. Your little trick of putting a bit of grease on the o-ring worked great! Put it all back together with the new one and there are no leaks and the bike runs great! Thanks so much for the lessons! ATB!

[@kenbrake2828]

I just rebuilt my 2006 Honda CRF250R carburator and there was 1 extra O-ring that none of the other youtube videos mentioned in their walk throughs. Now the carb is leaking gas out of the vent. Looks like I now know where that O-ring was supposed to go. Now to tear that bike apart again. I wish it wasn't such a PITA to get to the carb in this bike. This will be the 3rd go around with this bike. Thankyou for the thorough video. Smart man!

[@bearknuckles100]

Thanks Mr! Was having this exact problem with my 98 Yamaha Grizzly 600 carb. You're a good teacher & mechanic for sure! Cheers

[@marshallcollins8634]

I think it is halarious that your bench mat says ( get organized) 😂😂😂 Right after you mention the positive effect of being organized. Love how you even film the issues. You are always my first choice in learning anything for my 4 wheelers/ side by sides. THANKS

[@AndyMechanic]

Haha! That wasn't planned! Funny though! No problem at all, it's great to know the videos are helpful to so many people around the World - that's exactly why I do it :-) Appreciate your feedback, lots more videos to come. Cheers Andy

[@markborchers6613]

Andy, you're a legend. This was the exact problem with my Jinke PZ22 carby on a Lifan 125cc engine Quad Bike. It had horribly contaminated fuel when I got it from an auction, but oddly, not leaking. Carefully dismantled the bowl to remove contamination (the top "half" of the decanted fuel was deep brown!), cleaned and reassembled, only to find it started leaking from the overflow. Pulled it apart again, checked my work, no mistakes, all good, and it still leaked from the overflow! Aha! Armed with your information went back to the carby, pulled it apart and sure enough, the o-ring was blown. Thanks for the info!

[@trittany2882]

So how come it wasn’t leaking to begin with?

[@bobdelaplage690]

What steikes me is that you take the time to do intermediate small tests, to progress, in small but certain eliminating steps....that is great info! You are a good mechanic, great teacher, i subscribed, thanks Andy! Everyone should understand carburettors, they are everywhere🤩🚣‍♀️🇧🇪Belgium greets you!

[@bogdanmaftei9327]

Fixed my carburetor 5 minutes after watching this. You are amazind dude, thank you soooo much

[@lodyz5729]

Thought I would have had to skip a bunch to get to useful information. Was pleasantly surprised to find great troubleshooting ideas and a much broader understanding of carb fuel intake.

[@guyonacub4335]

Just found your channel You have given me the confidence to have a go at my wife's XT225 which is a pig to start Love your calm way of working Thanks

[@30gills]

Great video, super informative and great job explaining everything in a way a non mechanic can understand.

[@Podchynok]

Rather clever way to troubleshoot. Thank you for sharing your knowledge.

[@liamhagerty657]

My dr 125 sat outside for 4 years and thanks to this video i knew how to diagnose my carb that has been leaking for a week now. This video is the.l best vid i found

[@AndyMechanic]

Thanks Liam :-) appreciate your feedback & great job fixing that leaking carb. Cheers Andy

[@danielreidy1251]

Best simple carburetor diagnostic video I have seen. Thanks for the knowledge. Fixed my Kawasaki 500 with this.

[@messiahles]

Great Video !!! Very thorough and Andy knows what he is talking about. I like his calm and pleasant way of explaining whats wrong. Cheers !!!!

[@H8er-Maker]

Sum1 should give you an Oscar award for this video. It was exactly what my issue was. Thank you

[@zacgreene9728]

Just like all the other comments you saved me with this video. Nothing else like it out there. I greatly appreciate it. And you gave me some carb tips for a lifetime.

[@jazzysd15]

hi v. Hhu

[@1970PMD]

Mate, you have been a life saver for me, I rebuild my Mikuni carb as I have done 1000 times but this time I could not understand why the carb kept overflowing. Checked the float 10 times and it was set perfect. Turns out to be the plate that holds the barrel that holds the needle was not tighten enough to set the barrel's o-ring and seal properly. It was not until I seen your vid that it hit me, something so simple can cause a migraine headache. When you lifted the float with the fuel on it was an awakening moment for me. Again, thanks for your vid, thumbs up.

[@AndyMechanic]

Hey, no problem at all, I'm pleased you found the video helpful & got the problem sorted. Thanks for the feedback & keep safe. Cheers Andy

[@1970PMD]

@@AndyMechanic Another question I need to ask you, does the pilot jet needs to be screwed in all the way until it seats or does it need to be turned back a few turns? I cant seem to find the settings for this carb. The pilot jet is the only one I did not note the amount of turns from factory, I removed the old one and replaced it with a new one but failed to note the amount of turns, your input will be appreciated. Thanks.

[@AndyMechanic]

Hi, no problem. The pilot or idle circuit jet it screwed in all the way until it seats. The pilot screw however is specific in its position as it adjusts the mixture at idle. If it's the idle screw you are referring to then usually it's position is between 1 & 2 turns out from after seated, however this is specific to vehicle - service manual will have this info. Hope this is of help Cheers Andy

[@quaternion-pi]

Awesome tips I've not seen elsewhere. Solved my Honda mc quad carb problem while on the bench, not after re-installng on the bike and finding the problem not fixed. Thanks!

[@ianwang9164]

Lifting the float by hand to check if the valve is leaking is such a brilliant move

[@daneomegan]

Or you could simply blow down the pipe... If air can escape so can fuel

[@hlukufarmmechanic2497]

Hello.. Thanx for making this video.. My dad's tw carb drips a puddle on the garage floor overnoght.. Sure enough got a perished o ring around the seat...only after watching your video I realise this.. That gosh dang seat drops in super loose.. Thanx for your good lesson in this video I now know the proper way to diagnose a leaky carb step by step.

[@TheeArtist23]

I have a little honda rebel 250 leaking so much fuel. Now i feel confident in diagnosing the problem on the inside. Thank you so much!

[@tylerloveland2895]

Been a CAT tech for 20 years. Your videos are very watchable. Facts short understandable easy.

[@leezarutan6005]

This video was awesome I have a 2005 Polaris predator 500 and my fuel is leaking in that exact location I tried rebuilding my carburetor completely and still leaked never would have known that there is a rubber seal there or adjusting the level of the overflow tube 5 ⭐ sir

[@Akosyeah]

honestly this is the best video I've seen, thank you!!

[@jaquecousteau2976]

Great video! After taking my bike and carb apart 4 different times to change the main jet, each time I reassembled it leaked out the overflow Hose a lot !!! couldn’t suss it out and was getting frustrated... you helped all the way from New Zealand!!!! the culprit was my valve seat o ring,, thanks for this! Easy to understand and a solid way to troubleshoot and find the reason a carburetor is leaking.... Huge thanks !!!! Cheers,,, from Maryland!! Braaaaaaapppppppp!!!!!!!

[@AndyMechanic]

No problem Jaque, ride safe! Cheers Andy

[@Wabbit1961]

Ok, so I know this video is old but so is my bike! I have a 1986 Yamaha SRX600. You should appreciate this since you're a Yamaha mechanic. This is kick start only. My problem occurred about a month ago. I wasn't paying attention and overfilled the tank. It took a few kicks to start but she started up and I rode 3 miles home. Of course, it was getting rid of fuel out the tank overflow during the ride. I figured, oh well, no harm. Next day I go to kick start it and it was not even trying. I felt like the kick was just turning over the cylinder. As you know, if a kick start bike didn't start in a few kicks you can wear yourself out quickly. I tried and tried and tried over the last few weeks. Even open the gas cap, etc... I had about given up and all of a sudden she kicked over so easy it freaked me out. I let it run for a minute or so. It idled perfectly, never needing choke to keep it alive or anything which also freaked me out because it started and idled perfectly at 1,200rpm right from the get go. Usually I have to twist the throttle to start it up and then apply choke and ease off the throttle. Well, I turned the bike off thinking WTF it's fixed itself! I turned the bike off to lock the gas cap on and proceeded to kick start the bike and bluh... . Bluh.... Bluh... Once again she doesn't even attempt to start. Now, I know I'm getting fuel, I know I'm getting spark (even installed a new plug... Old one was not wet), I know the coil is good and the CDI is good or it won't run. I mean, it has to be a fueling issue. I'm about to pull the tank and replace all the fuel lines but somehow I think it's carb related.... It's not leaking fuel. Your thoughts?

[@ricardocleophas1242]

Hi Andy, thanx 4 your video it help me a lot. my Motomia Spitzer has been parked 4 over a year and today i decided to fix the starter to ride it again and as my luck is, the feul was streaming out of the carb. So thanx to your video I am able to fix that myself.

[@marvingochez3119]

Great video! I fixed my Honda’s leaky carb, though it wasn’t the same carb you got me to take mine apart and do the repair. Thank you.

[@dericnichols6804]

Your video was by far the most helpful, Thanks for taking the time to explain in detail how you solved the problem.

[@callumsimpson7483]

Good video mate. I have literally stripped and cleaned the whole carb/filter changed spark plug/fuel. Nothing come across this video and knew straight away that was the problem.

[@letsgetit3310]

EPICALLY INCREDIBLE VIDEO! I don't even have to keep watching anymore videos, learned everything in one go, I'm 100 percent confident i can fix my bran new leaky carb. Pretty soon this will be a documentary on carburetors lol. In a tesla museum lol.

[@alexlintern9779]

Kazuma Rage 110cc now runs fine! Thanks Andy for this video. I got the ATV working properly by having the blocked primary jet cleaned by a local dealer - they have a special set of super-fine file tools to clean the jet. The poor start and poor idle are now gone. I have fitted a bike fuel filter (it's tiny) in the fuel line and will put additive in the fuel before wintering the bike in the garage. Cheers again Andy & keep up the good work !

[@AndyMechanic]

+Alex Lintern Cheers Alex, good job :-)

[@alejandroavina8522]

70i>67

[@anthonymonks5216]

Thank you for posting this video, I thought I knew a lot about carbs but didn't know about that o ring prob, I have been trying everything to stop the leak taking carb on and off half a dozen times and now it is sorted thanks to you, wish I had seen your video sooner, you are added to bookmarks.

[@AndyMechanic]

Thanks Anthony, great to know it's all fixed now :-) Cheers Andy

[@Vernest3000]

Thank you Sir for making this video. You saved me from buying a new carburetor out of frustration

[@dtvtech3385]

Exactly what was wrong with my carb. Needle valve seat o ring bad. I diagnosed it from your vid. Thank you!

[@thelippy]

Just want to say thanks! This video taught me a heck of a lot. Hope you realize how many people you're teaching.

[@AndyMechanic]

+thelippy Hey, many thanks for the feedback. It's great to know my videos help people all around the World. Lots more videos to come too :-)

[@jaredmuszynski8996]

O-ring was cracked and shrunk on my CR250… fround a perfect fit off of a wacky ring for fishing, great video thanks!! would of never been able to fix it without this video

[@johncollins8304]

6:30 a.m. a year later. Still fascinating. Just a comment on that grease you were using when trying to squish that oversize o-ring on, just in case s.o. doesn't know -- it's red rubber grease which is safe for grease. What I thought was a dilemma: for garden machinery, which is not used over winter, we're told to turn off the fuel, run the motor 'til it runs out of fuel, emptying the carb so there is no build-up of crud. Here, the problem was that the rubber went dry because of lack of fuel so presumably the carb on these engines should never be empty.... But if you're not riding over winter and having a regular flow-through of fresh fuel, you'll have to put in an additive. I'll come back and watch this again in a year's time.

[@ronaldwhite5887]

Andy thanks for your diagnosis trouble shoot carb issues, very helpful glad you enjoy what you do.

[@haggistoursuk]

Thank you for a great concise video Andy! We have a bike with a leaking carb. 1 of 4 carbs on it will not stop leaking and this rubber seal is the only thing we have not checked. Absolutely brilliant. Keep up the good work. All the best from Haggis Motorcycle Tours over in Bonnie Scotland

[@AndyMechanic]

No problem....Good Luck sorting the leak. Great to know the videos are helpful. Ride safe. Andy

[@n7hevn]

This video is awesome, and you're a great teacher! This helped me resolve why my generator had a leaking carb! Thank you for the video, and mechanical education!

[@gregormartin5145]

Great video with awesome insight, I’m working on a mower carb and it gucked up and I have great knowledge on how to fix it

[@thirdworldTrini]

This is the perfect video I needed, my cbr600 f2 is dumping gas from the carburetor... I'm going to run this checks on it for sure 🙏

[@lauriegranlund3331]

Thanks Andy for your response. When I replaced the needle valve and seat I checked the old o ring and it seemed fine but I replaced it anyways. The new one looks pretty much the same size, not reduced in diameter like the shriveled up old one in your video. At any rate the situation is unchanged.... it starts, it runs but have to keep blipping the throttle so the fuel pump throws it some fuel.... if you try to rev it up it just sits there going blep blep at about 2000 or 3000 rpm and sounding like a partial backfire until it apparently floods out. So the situation seems to be BOTH flooding and shortage of fuel..... at a bit of a loss to explain how that can happen it should be one or the other not both. The PLUG, being a four stroke engine and not having a lot of run time doesn't tell much of a story.... looks relatively normal, not carboned up, not soaking wet, not completely dry.... and yet if I remove the tank or shut the gas off or pull the gas line from the carb, the engine idles and revs up normally until it runs out of fuel. The fuel petcock supply is full and normal, gravity fed only, there is no vacuum opening on this model. IS there anything else in there other than the float which could control fuel input to the bike? There is NO leakage out of the carb it's parked on fresh clean concrete and absolutely nothing. I have taken all the jets out and cleaned them and put them back, and double checked them and that too made no difference. Doesn't make any difference if the air filter is on or off. Exhaust isn't plugged, no bees coming out of it! AS ANOTHER NOTE OF INTEREST.... when I started it up a few years back I'm very sure that I had to run it with the choke in the pulled OUT position.... and it ran normally.... carb had never been apart at that point, I recall having a lot of trouble getting it to run in the "IN - RUN" position so I just left it in the "OUT - CHOKE" position and it worked..... [and it wasn't cold weather] I'm SURE that "IN" actually WAS the run position, and "OUT" was the choke position..... but I'm very sure that it was functioning opposite to what I thought it should be, so I thought "oh well" I must be mistaken... now it seems to have returned to the "out is choke" - "in is run" variant..... ever have anything go wrong in the choke? This carb doesn't have a flapper, it does something internally.... I'll take that apart tonight and have a look maybe something is gimped in the choke as I can't see how it could reverse positions on me. Thanks so much

[@AndyMechanic]

Thanks for all the info.....so your carb sounds like it's a CV (constant velocity) carb with a rubber diaphragm which raises the needle as vacuum in the intake reduces. If I'm right you'll need to remove the tin cap at the top (4 screws usually). Check the rubber for splits/perishing and also the o- ring that seals the tin top plate. Also check the air supply to the top side of the diaphragm. With the air filter off you should, when you Rev the engine see the slider rise pulling up the needle valve. If it's not a CV carb then let me know and I'll scratch my head a little more! Good luck :-)

[@AndyMechanic]

...oh & pull the choke plunger out - it too usually has an o- ring on the brass piston - check the piston moves freely & the in & out ports are clear too.

[@johncollins8304]

Excellent! Who'd have thought that a lesson on O-ring dimensions would be interesting?? But it was, and my interest in O-ring dimensions has grown to the size of a T-shirt. I'm here for what you did at 40min. Although the needle passed a pressure test, I wanted to see something more convincing: if I could put the bowl back on, and let petrol in, if the needle was seating properly, there would be no leak. But I wanted another opinion. And you have it! Thanks a lot. It's nice to do the pressure test -- which itself is better than just blowing into the fuel spigot (?) when the carb is inverted -- but the most convincing is having no leak from the float bowl!!

[@marksmotorcycle375]

Brilliant video, and everything explained to a T, ill be taking the carb off my quad tomorrow because it has sat for a year, and fuel is leaking out the overflow pipe. Great thanks

[@marksmotorcycle375]

My quad still won’t start, still no spark, though if I put the spark plug in my bike it sparks ok, I’ve replaced the cdi, the coil, and a few other bits, but nothing, the flywheel won’t spin either when starter button pressed, starter is spinning though, any ideas????

[@AndyMechanic]

Engine siezed or starter Sprag clutch has failed

[@ravi3457]

i dont even have an atv but this video is the one that i need. thank you so much.

[@geraldjohnson621]

Thank you for making this video very informative my scooter is constantly leaking from the overflow bowl I will check it when the weather is nice here in D.C.

[@michaellane6841]

Hey I just wanted to say thank you very very much for taking the time to make these videos! You are very good at teaching and very talented mechanic! You helped my son and I fix his bike! I’m very great full for this video!

[@rhkips]

Always good to amass a collection of O-Rings! If you wanna go properly bonkers, start collecting them in various materials (Nitrile, EPDM, etc...) to save the day in any application. :D I love carburetors. Such amazingly simple little things that're so capable for what they are. I recently took a job with a company that does repairs of lawn, garden and construction equipment. A bit of a shift from the automotive world that I'm used to, but so much of the knowledge carries over. I think there's a lot of real-world value in teaching the operation and troubleshooting of carburetors in trade schools. :)

[@jadegb5474]

Good video and spot on because I have already done this. Had trouble getting the "o" seal in but a bit of vaseline does did the trick.

[@jrnchristiansen6198]

Thanks for good videos in the right tempo. Ready again for a second atempt with carb on my GN 250 after 7 years hidden in the garage. Aarhus, Denmark.

[@nealbuschman895]

Great video. Easy to follow and replicate to diagnose the fault. Thank you

[@ericelsea8678]

Great video. Very helpfull on my hardtail custom with a 100ci revtech. It's got a mikuni hsr42 carb and this fixed the issue with the o-ring on the float needle brass housing. Thanks.

[@lauriegranlund3331]

Thanks Andy for your further thoughts on that carb on that 2004 TTR250. It is a cable push pull style throttle, there is no constant velocity diaphragm either under the top cover (it's just a dust cover with a paper gasket which appears intact, there's nothing inside but the physical leverage for the throttle)..... there is also a side plate which is just a cover for another variant of this carb in another application, there is nothing underneath it. I retested the float and needle valve and seat and it fully shuts the fuel flow off when in the level position, allows it through when it is lower, so I am confident that is working as it should. With regards the choke, on the end of the choke there is a flat surface which appears to be intended to seal the end off when the choke is in the "off" [in] position.... from the factory microfish I could not tell if this is supposed to be an o ring that has collapsed or not. I ordered the entire assembly but of course it is backordered so who knows if I will get it or not. I note that on the assembly above the main jet, the long brass tube with all the holes in it that the slides needle goes up and down in, has a place where one might imagine an o-ring might go..... it is machined into the brass ..... but no remnant of an o ring there at all, just NOTHING. Back to another week in the ultrasound, beyond that I am running out of ideas.

[@AndyMechanic]

Hi Laurie, the extra information is most helpful. Please email me the VIN of the bike to [e-mail] I have a couple of Yamaha TT250R Raid bikes here plus some parts diagrams too - these should assist in deciding where there should be o- rings etc. The tube with the holes in is the emulsion tube - responsible for fuel atomization so having the holes clear is critical I'll also get you the specs and procedure on how to set float hight. Please also check your floats aren't holed - fuel inside the float as this will cause a big problem I'll keep an eye out for your email. Include pics of carb & any identifying numbers please. Cheers Andy

[@RezziOutdooringandRVing]

Wow! This video was awesome. I was looking for information on why my 2hp outboard was leaking fuel when I opened the valve and came across your video. Now I think I have enough information to tackle this on my own instead of taking to my local repair shop. Fingers crossed!

[@Timberjo2]

Ok Andy, now I want that video on adjusting float height.

[@AndyMechanic]

It's on the big list of videos to make so one day :-)

[@marccawood]

I learned a lot watching this. I have a leaky carb (overflow) with new valve and seat and float height on spec and even 3mm and 6mm over spec to get more pressure on the valve. Still bloody leaking.

[@julian11able]

im glad i watched until the end, where you covered the issue of spline alignment

[@stevewallace7397]

Fantastic tutorial; thank you. Helped me on several different levels. Thanks again, 2003 Yamaha 660 Grizzly

[@philipsmith2208]

Great video Andy thanks - that o-ring is almost certainly the problem causing the same symptoms on my '03 Yamaha TT600R. Bits sourced!

[@AndyMechanic]

+Philip Smith Cheers Philip, let me know how you get on. Cheers for the feedback. Andy

[@antonispanonidis5773]

This video saves me from going to die!i fit new gasket and it leaks ! When i see this video i fix it !ttr 250 keep it up !!!

[@anaussie3153]

I had this issue with my dads old 80s Suzuki dr 250 helped me out a lot thanks 🙏

[@johnpeters4342]

Having problems with fuel in air box replaced fuel pump still happening.think it's draining from tank throu carbon tank to air box

[@TheOriginalProfG]

Hi, This video was made quite a few years ago so I'm not sure whether I will get an answer, but you never know until you try so here goes: I have a similar carb on a 50cc moped. It leaks. I've had it off a number of times and checked the float, which is OK. The carb is very very very similar to the one in the video. The carburetor is leaking from the small eye portal on the air intake side (the small one below the one with a bearing). I have had it off a number of times and checked the float etc. When blowing through the fuel intake the air passes with no resistance whatsoever, and when I hold the float up, the resistance is at 100% preventing the air to flow which means the fuel will also be prevented from flowing. This means the problem is neither the float, nor the float vale and not the O ring. A few people have also looked at it and cannot fathom it out. Again, the carb is almost identical to the one in your video. What else do you think it could be? A new carb delivered costs almost £200 as the scooter is Italian and it has to come from Italy. There has to be another option. The previous owner (or previous to him) had disconnected the 2 stroke oil tank so I have to premix the fuel before putting it in the tank.

[@jdepas54]

how have more people not watched this. this literally is so helpful. well done mate good one

[@stuarthay1]

Excellent video Andy. At the end you mentioned the crank case full of petrol. That’s the problem I have. But it’s on my pressure washer. I presume it’s the same process. A long video that some will not like, me I enjoy that. Learned a lot from this. Thank You 🙏

[@stuarthay1]

P.S. SUBBED.

[@garyarms9647]

Thank you so much brother. I really appreciate your time, and knowledge. It is truly a blessing...

[@martinndanga8298]

Wow! Brilliant video !! Found it really helpful... I have a leaking carb of my eurorider 50cc v-sport scooter...I'm gonna definitely have a crack at it!! Awesome Andy...

[@jimbellingham3572]

I had a 1963 Pontiac 283 2bbl on a cast iron intake, front 2 carb studs rusted off. Carb flipped up at front and spilled gas on2 hot manifold. I had an extinguisher, popped the hood, 8" long "mortar" tube and breather cap at the front of the engine, crank case vapours ignited and blew the breather cap out of the "mortar" tuibe! just clipped my left ear, dented the hood rein4cing rib!

[@TheNostorian]

Very interesting. Just bought a 2002 dyna. Believing it might have this problem. Time to pop the carb in the morning.

[@malboyce3468]

Great video and excellent detailed explanations ... loved the bit about the O ring measurements and how you overcame it. My newly acquired 98' Husky is draining fuel from it's vent and I was looking for float height stuff on YT. The last owner said he had recently rebuilt the carby and he had since had issues ... with the information you've shared I'll be better prepared when I go looking for the problem - Thank you Andy.

[@AndyMechanic]

Cheers Mal, pleased you found the video helpful. It's rare it's float height so only adjust if you are really sure it's out of spec Cheers Andy

[@malboyce3468]

@@AndyMechanic Thanks Andy, I just had a look a look at your channel to see if you had a video about float height .... but kinda got stuck with the tool girls instead ahem. Did you ever make one on float height? I understand that if it's too high [fuel] it can make your bike run lean and too low rich or vice versa due to mixture. Be interesting to see your take on it as the way you deliver information is brilliant, and NO I wont be adjusting the float height on my bike unless its the absolute last resort and the bike is a TE610 so I have no need to mess with the carby to go faster just last longer :-)

[@AndyMechanic]

Cheers. I'm preparing a video on float hight adjustment. However, the method of measurement varies greatly between manufacturers so it's not that straight forward unfortunately. Cheers Andy

[@malboyce3468]

@@AndyMechanic Well it turned out to be the float height, or specifically the brass rocking lever that controls the floats. The Dellorto PHM on my bike has independent floats. If you lay your hand flat on the table and raise one finger that's what the rocking lever looked like [approx 3mm difference]. I straightened out the lever and measured both were equally parallell to the body [per spec'] and all good. Needless to add the air mixture was way out and backfiring flames on decel', idle would increase then slow down and then die, hard to start etc. I've got it leaned out now with the occasional backfire amd stable idle so more to do there. I live in a studio so my bike is at friends place where I can work on it but it's only 1 day per week [50km away]. Anywho please forgive the punctuation I just thought it weird that the guy I bought it off left it like that and I dont ever remember having float height issue on my bikes in the past ... then again I'm no engineering mechanical genius. Love your work Andy :-)

[@AndyMechanic]

Cheers Mal, pleased you got it sorted & thanks for taking the time to let me know what the issue was. Ride Safe :-)

[@peted2770]

Thank you for this video. I was pulling my hair out on this leak and didn't even think to check the o-ring.

[@malgray7396]

Thanks Andy last guy spoke different language...so no idea.. But love your explanation... Thought mine could be o Ring as well Suzuki 1200 SS 4 carbs ,1 leaks horribly Cheers Mal

[@larryniidji]

You mentioned screw head rounding. Not only does it happen due to the very tight screw but also the screw driver. Japanese Industry Standard (JIS) screws appear to be phillips-head screws but the drivers are different. I bought a set of JIS screwdrivers off Ebay and what a difference.

[@williamwilliam5940]

Best tutorial on KZbin, thanks

[@AndyMechanic]

Thanks William :-)

[@iancunningham7547]

It is quite obvious to me that I won't be fixing the carburettor (which I think is responsible for the fuel coming out the air filter) on my rotavator - well beyond my pay grade. But what a good video with great diction. I am sure Andy's good at mechanics but I think he's a great presenter.

[@AndyMechanic]

Thanks Ian, I appreciate your feedback. Sorry to hear you have an issue with your rotavator. The main reason why I took the job as a Lecturer at Unitec (previous job) was to learn how to teach, how to deliver the info in a way that kept the attention of the students. They seemed to like how I did things :-) Stay safe. Cheers Andy

[@HaidsK2]

just what i needed to see tonight to fix my carby, thanks mate was extremely informative!

[@raymondamenyo1425]

I really enjoy your video today my name is Raymond from Ghana I am riding on Kawasaki El 252 I am facing an overflow problem I'm going to try your teaching the results I will come back to you

[@johnhunt2388]

Now I know how to fix my line trimmer so I don't have to empty the petrol to store it away, Thanks heaps.

[@roumelvalero6688]

Brilliant! Thanks mate! Watching you from the Philippines.

[@michaelgilbert2559]

Very informative on the workings and repair of a carburetor++++++

[@daddyfixit5188]

I have this problem with an outboard 😀 now I know I got two carbs to sort. I would have put o ring on a bolt in drill spun it up and shaved a bit with wet n dry 👍👍👍👍 nice vid necessity is the mother of all inventions or late nights in the garage thank you

[@gavinterry8948]

Great video - thanks. I have a leaking carb on my YZ125 and I am going to try these steps to cure it.

[@michaelmaillet8528]

Excellent video, I’ve been working on carbs for years and always come to KZbin from time to time and just came across this. Great job on explaining, demonstrating and entertaining!!!!

[@michaelmaillet8528]

And I forgot to add the most important part lol. Spot on what the problem was with a carb I’ve been having problems with..Thanks a Million

[@TrojanStarryNight]

You are my hero! With your video I think I found the issue with mine.

[@jthan258]

Thanks for this video I feel confident to DIY my self keep up the good content

[@danielbutler4925]

You make great videos. Good explanations and good visual demonstration.

[@AndyMechanic]

Thanks Daniel :-)

[@AlexTonnerKingDugong]

Eureka!!! Finally found the fault with my carb, thanks to you!!

[@AndyMechanic]

Great job :-)

[@christophermerritt8998]

thank you for your testing tips! Ill be using them today on a yamaha 350 big bear. great video!

[@alexlintern9779]

Here I shall post some comments that will hopefully be helpful to others. I used Andy's instructions to get the job done and successfully cure the fuel leak. The carb is a PZ 19 L and does not have a sealing o-ring for the float needle valve but the valve does have a rubber coating. I cleaned the jets and ensured the valve slid easily inside the jet. The carb does not leak however tuning the carb up will be necessary so this might be a good idea to cover. My quad bike does not have a fuel filter and wondering if this would be a good upgrade to make. I used new fuel lines that are much better quality too.

[@AndyMechanic]

+Alex Lintern Hi Alex, yes fit an inline fuel filter as even a small spec of dirt or rust can hold the float valve off it's seat and cause it to leak and over flow the float bowl. Thanks for your comments. Cheers Andy

[@SSSILENTPRODUCTIONS]

This was exactly my problem and I fixed it. Thank you!

[@justonovak8216]

Excellent job. Thanks for the video. Brilliant!

[@rolexmccollin2331]

Good afternoon Andy I am so happy you respond to my comment ok I live in Guyana a small country in south American I sell used atv which I imported from United States of America.,one of the 500 honda fuel keep leaking fuel from the carburetor I clean refit same ,remove and clean the same .but I need to look after is by myself so I am seeking your expertise I am a mechanic but does not like working on carburetor from day one ,so let me see what other information you have have a guy fix them for me but I am determin to do it myself thank Andy.

[@AndyMechanic]

Hi Rolex, can you tell me the year and model of the ATV and I'll obtain a copy of the service manual so I can get a good idea of which carb is fitted to your bike. Thanks Andy

[@HectorGarcia-eo1lq]

Excellent information and great video Thank you for sharing

[@ericmartin6657]

Thanks for your teaching videos!