Shapeoko 5 Pro Assembly Guide Video - V3

UPDATED Version 3: Welcome to the Carbide 3D Family. Getting your machine up and running is straightforward. Here, Kevin takes you from boxes to an initialized machine. By watching this video and following the downloadable PDF guide linked below, you'll soon be experiencing the power of a benchtop CNC router.
S5 Pro PDF Assembly Guide:
my.carbide3d.c...
If you ordered the 65mm Air Cooled VFD Spindle with your machine, congratulations.
One Note: Be sure to install your spindle carrier in the middle position of the Z-Axis, and watch the video below for more install advice.
VFD Install Video:
• Meet the Carbide3D 65m...

[@dwidgit332]

Just in the process of building my machine now. This video and the latest version of the instructions don't see to capture that the drag-chain bracket that you mount the wiring harness to on the gantry is shipped as a separate part and is not pre-mounted on the left and right rails. While it appears that it could be mounted in two different positions, based on the position in this video and the manual, I believe it should be mounted to the set of holes closer to the center of the gantry. Hope this helps anyone else wondering where to connect the drag cable to!

[@ninjatrader7785]

Just finished building mine and besides a few missing screws which I was able to substitute with the spare ones, only one issue remained. The grounding block should come with 2 M4x30 screws, but mine are M4x35 so the block won’t tighten since the extra few mm are enough to bottom them out before the block tightens. No big deal, I’ll make them shorter with the Dremel tomorrow and that should do the trick. Might want to check on that though since I am probably not the only one who got the wrong ones.

[@BeardnScars]

Hope they read this. Did you happen to follow up with them as well?

[@brittphillips5308]

Got through putting mine together last night and noticed the router cable only just makes it through the cable harness. I'm sad to see I'll need to get a small extension to run it to the tables surge protector. Did I luck out with a shorter than normal Cable or is this intended, if so whats the reason?

[@nanoblasting]

Great video ! 👍

[@jmichaelstone]

Kevin, would you accept a bribe in exchange for a video on tramming the Shapeoko 5 Pro? I just got my machine set up and running a couple weeks ago and I bought the recommended Edge Mini Pro Tram System, but I'm afraid (or possibly too lazy) to use it. You guys have a video (with Winston) from like 5 years ago, but the equipment's all different. Even if the principles are the same, it's knowing which screws to fiddle with that's giving me pause.

[@carbide3d]

You can send the unmarked, non-sequential $100 bills to the office, c/o Kevin Secret Video Location: kzbin.info/www/bejne/rZLIqXipaMh2erc

[@jmichaelstone]

@@carbide3d Huzzah! This is perfect. Your money is forthcoming (by mule, so it might take a bit).

[@xyzspec82]

I like the vibe lol

[@SkySim]

My 5 Pro 4x4 has been sitting in its boxes since Jan 23 cause I don't have space to install it yet. 😥

[@carbide3d]

This is just the exposition part of your story. The rising action is upcoming!!

[@Kiromos]

Do the hex keys come with the machine or should I buy some for construction? I have regular L shaped alens but those Ts do look like a time saver especially for the bed.

[@carbide3d]

There is a toolkit included. Everything you need to build the machine is in the box.

[@carbide3d]

As mentioned, the T-Handles are nice for exactly that part of the job. On a 4x4, that's a lot of bolts

[@Kiromos]

@@carbide3d I just put in an order for a Shapeoko 5 2x4 yesterday so I am just trying to soak in as much info as I can before it arrives!

[@carbide3d]

Welcome to the Family. Be sure and check out My.Carbide3D.com for more step by step videos and learning resources. Great things ahead!!

[@marktroendle]

Please help when turning on Carbide motion for the first time I do not see how to get to the machine set up wizard

[@carbide3d]

Mark, reach out to [e-mail] Our staff will help get you up and running. Let them know you are new to the family. We got you.

[@Tek_42]

Should I and/or how do I go about securing my 5 Pro in place?

[@carbide3d]

You should not bolt it down. It will not move under normal operation.

[@Tek_42]

@@carbide3d Perfect, thank you!

[@chrish7650]

80mm gas strut assembly video?

[@carbide3d]

The video is here: vimeo.com/869209967/01fbdc4152

[@carbide3d]

Full instructions are here: my.carbide3d.com/docs/gas-strut-kit/

[@wadetomczyk8043]

So serial in the build video haha.

[@qr5558]

How much?

[@carbide3d]

shop.carbide3d.com/products/shapeoko5