Carbon 10" Pipe TIG Welding Root Pass !

Tig welding root pass on 10-inch carbon pipe. Field weld TIG techniques! This video is about the combination of the tig welding techniques, such as; the constant feed technique, and dipping method on the root, hot pass, and cover pass or cap. The welding technique used will depend on the thickness of the pipe. You can either free-hand or walk the cup on a thin wall pipe. This is because you will have a shallow bevel that you can walk on with the cup. If it is a heavy wall pipe you will want a cup size that is small enough to fit between the groves and slide easily. The video gives viewers good insights into placing excellent and solid root passes. You will get to learn about different technical paths that you can explore. With the appropriate training and practice on the operator's part, learning to place the root can become an invaluable skill!
#tigwelding #tig #tigroot
None of these videos are recorded in a fancy shop surrounded by sponsorship banners!
My videos are recorded at working sites in various locations and welding positions.
90% of my welding projects in videos are x-rayed, and if you like to see hands-on projects, welcome!
If you liked this video please give it a thumbs up, share it, subscribe, and click the bell.
It doesn’t cost you anything but massively helps my KZbin channel. Thank you.
Support this channel with 🔔 Subscribe and 👍 Like!
/ x3mtig

[@alexisrivera1850]

Good video I'm a combo welder in Texas

[@X3MTIG]

Thanks bro!!😎

[@ivang8025]

Thanks!

[@X3MTIG]

Hvala ti buraz, puno mi ovo znaci!!😎👍

[@mddenis1]

So much satisfaction for a welder to see good root)

[@morgostas]

Great insight in all steps: edge prep, root and fill pases. Also overcoming field obstacles such as vents, wind from fans, and tethering belts. To me theese videos are of great value. Like i was there on the job sight. Thanks so much for sharing 🙏 💥 👌

[@X3MTIG]

Thanks man!😎

[@Kevin-xz1go]

One of the best if not the best channel for info and tutorials thank you.

[@X3MTIG]

Glad you think so!

[@cultm]

Nice work again man. My virtual teacher 💯

[@X3MTIG]

Glad to hear that!🙂

[@sergcyxa]

Thanks mate! So clear explanation without unnecessary words 👍

[@X3MTIG]

Glad you liked it!

[@zodiac8824]

Im a welder, and i still come to watch your videos for improvements. Amazing work.

[@X3MTIG]

Thank you brother 👊

[@stipe573]

Perfekcija ka i uvik!!💪🏻✊🏻

[@X3MTIG]

Hvala brate 👍

[@mohammadabuhamed3513]

Beautiful lookin root and cap man!!! 🔥🔥🔥

[@X3MTIG]

Thank you brother 👍

[@paulpalic9294]

S nestrpljenjem cekam svaki video 👏👍Napravi neki pay pal racun da ti bar kavu uplatimo ako nista, dobro nam pomazes!

[@anks4343]

E pa to ti je bar lako, ispod videa di imas opcije za like, share i download, imas i opciju thanks$ I tak mu mozes uplatit cifru koju oces i direktno pomazes njegov kanal! A on je zasluzio definitivno i par kava i vecera!! 👏🏻😊

[@paulpalic9294]

@@anks4343 super nisam znao .Dašta neg zaslužio !

[@ivang8025]

@@paulpalic9294 Slazem se buraz s tobom, pomaze nam fakat puno! Ja sam mu gore uplatio taj super thanks, lik rastura💪🏻🔥🇭🇷!!!

[@X3MTIG]

Hvala ti puno!! Kao sto su ti vec rekli, imas gore opciju" thanks$", to bi mi puno pomoglo definitivno!!🤗

[@goran5056]

Odlican video buraz!!! 💪🏻Treba vjezbat sad…narednih 20 godina🤣

[@X3MTIG]

Hvala ti buraz, ma daj ajde , mozes ti to i brze 😎💪

[@mikewelder7014]

Amazing video brother! 🔥🔥🔥

[@X3MTIG]

Thank you bro!🙂

[@paulpalic9294]

Hvala!

[@X3MTIG]

Hvala ti puno prijatelju za ovo!! 😎 Puno mi to znaci!!😇

[@Fnhx5ff]

Как бы я хотел так уметь варить как ты. Спасибо за видео тебе.

[@cure5073]

You are a beast bro perfect job is a joy to watch and learn from you thank you

[@X3MTIG]

Glad you enjoyed it

[@neilnottingham6074]

Beautiful, quality workmanship. I enjoy watching fellow tradesmen whom love their work as much as I. Keep up the great tutorials and videos. Cheers Neil

[@X3MTIG]

Thank you my friend I appreciate that 👍

[@waylonroberts8719]

That was one of the best videos I've seen so far in field experience I've learned more from this than the other videos 👍

[@benjaminmarcinek]

Amazing work! You make look so easy and effortless, I guess practice and experience does make perfect. Thank you for the wind/lighter trick I've never seen it before, I'm gonna carry one with me now, scattered porosity sure is no joke.

[@X3MTIG]

Thank you very much my friend! 👍

[@khalidabouhassan5836]

Another great video! You are the best of the best man, the GOAT!!! 👍🏽🙌🏽🔥

[@X3MTIG]

That’s a big words my friend, I really appreciate that brother 🙏

[@timothyhendershott9333]

Another excellent video from the master. Do you have a favorite lens brand? Is there anything that helps you see better? Thanks again. The grasshopper to the Master. Sparky

[@X3MTIG]

Thanks bud, sometimes I’m using Optrel brand, but generally just regular lenses. So far no issues with my eyes 👀, fingers crossed hopefully it will stay like that for a while!

[@pacebozeman]

Combo here. About 15 yrs exp. 2 questions, number 1 how do you get such good arc shots especially by yourself lol. Number 2, how are you sneaky enough to not get caught filming? Im at a methanol plant in Louisiana and man they are crazy strick with phones. Especially photos and whatnot of any piping systems or vessels.

[@X3MTIG]

Hi man!! As you said, I have to be sneaky enough to not get caught😉

[@philipmorris1260]

Excellent root , fill and cap. Do you have any video footage of doing titanium pipe welding?

[@X3MTIG]

Thanks bud, unfortunately, don't have any at the moment!

[@grabbabitewelfed1641]

Awesome work brother👍

[@X3MTIG]

Thanks ✌️

[@darnold1984]

Great videos from a strong 488 hand 👊

[@X3MTIG]

Thanks brother 👊

[@brianbeaubien7371]

That is so beautiful and precise thank you brother!

[@X3MTIG]

Glad you liked it!

[@Tyler-xl7po]

any recommendations for a 2 inch carbon steel

[@tata2692]

Hi mate, as always good video. My question is, how many weld joints u are able to do in one shift? Is it 250 or 300 mm pipe diameter? I like to watch how do you weld, im welding as well, but always love to see how someone else is welding.

[@X3MTIG]

Hey bud thanks for your comment! I can do two 10 inches or 250 mm , butt welds in position if I want to per shift.

[@BlakeHockensmith]

Hey sir as a 2nd year I was always told that if you have the ability to tie in perfectly then you dont need to worry about stopping too much. Obviously a seasoned pipe welder usually can run from 6-12 no problem. But I was wondering if thats kind of a myth?

[@OkinawaWild]

Nice work. Can you share what your camera set up is?

[@richmonddechavez7946]

I learn more for you.thanks a lot sir❤

[@mickg7001]

How long takes to make that weld from root to cap?

[@X3MTIG]

10 hours shift, fit up and welding.

[@Ezrasideas]

Since you had a pretty inconsistent gap, I was wondering if you could do 5/32 laywire in the spots you had a 5/32 gap? Also what heat would you run that on for the 5/32 lay wire or would it be best to do the dip technique

[@X3MTIG]

Hey bud, yes you could. I would prefer to use 5/32 rod on 1/8 gap instead, as I will crank up the amps and push that rod inside the root with laywire technique. Probably around 140-150 amps.

[@dummurudramurty5147]

Looks good bro

[@АндрейКисляков-е4н]

Отличное видео и пояснения. Спасибо!

[@shawnramey614]

I’ve been practicing back feeding but I’m having a lot of trouble. The inside of the pipe looks decent, but the weld on the outside of the pipe on the overhead section is very droopy. Any suggestions?

[@cleon135]

I've found that happens when you're running a bit hot or sitting in one spot too long. Try turning down 5-10amps so it allows you to catch up with your wire if you're not comfortable with traveling faster. You really wanna make sure you're pointing at the bevels instead of right in the center. I had to mess around with a lot of things to finally get less suck back on mine aswell just takes practice👍

[@cultm]

Lower your amps,you're burning the edges.

[@shawnramey614]

cleon135 Thank you for taking the time to reply. I greatly appreciate that. I tried turning down the amps and it actually made the humping worse on the outside. When I ran it hotter, it laid a bit flatter. I think that I’m not traveling fast enough bevel to bevel? Also, what angle should I hold the filler metal at? I’m holding it straight down through the top of the pipe as I weld the bottom

[@cultm]

@@shawnramey614 Hold your filler wire between the gap,and try backfeed. It will be easy if you walk the cup,bottom part of the pipe; push more rod, try like back feed technique. On the side wall or 9 o’clock speed up or pull rod slightly outside the bevel, and on the top part; speed up, keep rod above that bevel edge, gravity will push that puddle down.

[@shawnramey614]

gruzin500 Thank you so much for the tips! I believe that’s what I’m doing wrong as I’m backfeeding, I’m not pushing the wire slightly outside the bevel, I’ve been keeping it fully on the inside!

[@Kacpin]

How could you control this? If i put 120 amps its burning like hell

[@dennyzeecko5183]

How do you get yourself to relax that much? Your welding looks very good.

[@X3MTIG]

Tbh, I don’t even think about it. I guess it comes with the years of experience!

[@felixlefebvre793]

Would like a SS sch10. 3" or 4" video. Thx

[@anthonyembleton5588]

What size gap did you used ???

[@X3MTIG]

5/32

[@giovannituyac7184]

Thanks a lot sir.

[@arshadmasih0410]

Good job sir

[@2kings4life]

What means tie-inn?

[@X3MTIG]

Tie in, where you connect your root pass.

[@SteveoDaily]

The feathered edges seem to drip in the wrong direction for a moment before the filler dip.

[@edeworpromise3619]

Please I'm from Nigeria I'm a welder combination welder but still want to learn more because I'm not that perfect yet

[@X3MTIG]

No one is perfect my friend, but requires a lot of practice to become good at it!

[@IrimerJimenezRivero]

Simplemente excelente

[@rajeshdalai4946]

Nice

[@larrylaird91]

Very nice root,and I know exactly what a little breeze will do. I've had to use 309 stainless to carbon to get the porosity out and it works.....

[@RealOthukeIGRA]

Please, someone tell me, how do I get a good root penetration on my TIG root pass? I wiggle the cup very nicely but can't get a good penetration. Please how do I get a good penetration on my root pass? Thanks 🙏🏾🙏🏾🙏🏾

[@X3MTIG]

Hey bud, that’s something you have to discover by yourself. Videos can help you to understand basics, but you need to experiment what’s working best and improve in that direction. Could be lots of factors, like; inclination, amperage, travel speed, gap, etc. Prepare few pipes with different gap size, and see would it work better. When I started with welding I was making notes of what’s working and what not!

[@RealOthukeIGRA]

Thanks a lot sir. I appreciate. Will work on that

[@brandonmendieta]

PLEASE PLEASE can we see you body positioning where you place your arms where your leaning your body weight Crouching or kneeling !??!?

[@X3MTIG]

Maybe in the next video, I’ll show some examples

[@weldingbilgin]

Kolay gelsin 🇹🇷

[@brianbeaubien7371]

❤❤❤❤❤

[@badoudiop2418]

bon traveil

[@Kishkomed]

ths

[@linassiskevicius7242]

Nice