Beautiful. Looks like I might get a replacement for my sadly now tail-less Elf.
@geode_rc28 күн бұрын
Good choice!
@lebojay7 ай бұрын
I’m determined to 3D print a DLG one day. We’re getting closer. Thanks for this! My current 3D printer can’t print this material, but my next one will be able to 😎 Greetings from Canada 🇨🇦
@geode_rc7 ай бұрын
👍 … BTY, You can do it with PLA+ …. Check out my BUG 3DP in my YT channel
@taoyeblue7 ай бұрын
Bravo from Bambu Lab as a 16-years RCGroup member.
@geode_rc7 ай бұрын
Thanks for watching!
@AerialWaviator7 ай бұрын
Such an inspirational design. Many intriguing techniques used here from the printed wing jig to the use of carbon. Thanks for creating and sharing. ♥👍
@geode_rc7 ай бұрын
Very welcome!🤗
@OliversAviationvideo5 ай бұрын
Ive just downloaded this and cant wait to print it.
@geode_rc5 ай бұрын
👍
@k.o.07 ай бұрын
Very elegant design. My only question in the build was the spring loaded rudder and elevator. I understand why you did this was for weight and ease of string servo control, but, as your crash indicated, expecting the spring up force during momentum didn’t happen as I predicted. I advise a lightweight aluminum rod (I have used bike spokes) to provide reliable servo control to surfaces. Otherwise many thanks for releasing the STL files, I am tempted to build it! Keep it up!
@rehepeks7 ай бұрын
I use spring and string even on 1.5M DLG. Never had any issues.
@lebojay7 ай бұрын
No decent DLG uses push rods. Too much weight and drag. Springs and strings are the way to go.
@filipporossifavilli687 ай бұрын
the only thing I can say is THANK YOU!!!Greetings from Florence Tuscany...
@geode_rc7 ай бұрын
Thank you too!
@franciscoblazquez91277 ай бұрын
The model looks spectacular, I need one in my collection XD
@geode_rc7 ай бұрын
Thanks you
@SuperRaymondh3 ай бұрын
fantastic design work! Cannot way to try to print and build this.
@geode_rc3 ай бұрын
👍
@carolinaboy0086 ай бұрын
Good evening, printed the right-hand wing jig this afternoon and it printed as one piece instead of separated as depicted in the design layout and this video (3:48 minutes). I am using Cua as my slicing software, is there something that I need do to allow for this? Thank you!
@geode_rc6 ай бұрын
Best to use Orca slicer, otherwise you would need to export as “generic” 3mf from Orca/Bambu Studio, then open in Cura as “project”. If there is still problems, please share a picture ( preferably on RCGroups). Easier to debug 😀
@Sandokans17 күн бұрын
Hello. What material used for covering wings, and where did you buy it? ❤
@geode_rc17 күн бұрын
@@Sandokans I use so-lite. Most of the llight weight covering film will do just fine.
@timmytom7 ай бұрын
That's brilliant. Thank you.
@geode_rc7 ай бұрын
Glad you liked it!
@charlesirons18927 ай бұрын
Wow, very impressive!
@geode_rc7 ай бұрын
Thank you! Cheers!
@HoNau776 ай бұрын
Great and thanks for sharing!
@geode_rc6 ай бұрын
Thanks for watching!
@bolleboom17 ай бұрын
goedemorgen...wat een super mooi ontwerp ..het eerste ontwerp was al super ....maar deze gaat er ver voorbij....printer gaat vandaag draaien
@geode_rc7 ай бұрын
Thank you very much
@lebojay7 ай бұрын
Hallo! Ik sprekt een klein beitje Nederlands. In 2000-2003, Ik woon in Amserstam. Ik kom bij Canada. 🇨🇦 🇳🇱
@franciscoblazquez91277 ай бұрын
When I try to open your 3mf files with Cura or prusa slicer it tells me that there are no objects in the file, can you help me?
@geode_rc7 ай бұрын
This release is designed for Bambula Studio / Orca slicer. Thanks for downloading
@robson.pampulha2 ай бұрын
I had this problem but I managed to solve it. Do the following: install the Bambu Studio software. After installing it, add your printer (since we know you don't use Bambu) and then you will be able to open all the files. Here's a good and valuable tip: open a Bambu Studio window and another window that contains your printer. After that, use Alt Tab to switch between these tabs and copy the information from all the Bambu Studio fields that contain the Bambu printer to the other tab that contains your printer. If necessary, make your adjustments. Save the printer and filament profiles. In my case, I had retraction problems that were only solved by using high speed and pulling back a few millimeters of the filament. For retraction to work, set the filament retraction settings and the retraction speed in the filament profile and in the printer profile, otherwise there will be a conflict and you won't have the retraction necessary to avoid strings. Happy flying!
@adametannecle27227 ай бұрын
Do you think esun pla-cf would be a good option? Just extra care for covering and storage?
@geode_rc7 ай бұрын
I think you’re doing great 👍
@xoltri6 ай бұрын
Why are there two horizontal stabilizers? It seems one of them has an additional bracing on the front 1/3rd, not sure which to choose.
@geode_rc6 ай бұрын
It's a tradeoff between strength and weight. Depend on how strong you like to launch.
@cnsapam6 ай бұрын
Am thinking of printing this using PLA+ instead of PA-CF, as PLA+ is more economical and readily accessible to me. Earlier thought of building Bug 3DP, but as I primarily use OrcaSlicer with Ender V3 KE, I found this files more easy to work with. Am almost done mapping all the files for my printer in OrcaSlicer. Any advice will be highly appreciated. I don’t have access to 7mm OD tube. Instead I can get 6mm OD or 8mm OD tubes, both of which are with 1mm shell thickness. Which one is recommended?
@geode_rc6 ай бұрын
Great to hear you’re making good progress. PLA+ is ok , just be careful not to over shrink the covering film. Otherwise, the ribs might bend. Same for tail feathers. 6mm will be better….. 1mm wall likely will be heavier than Skyshark P90 tube.
@cnsapam6 ай бұрын
@@geode_rc thanks for the advice. Will make sure that I don’t over shrink the film. As I’ll be using PLA +, will try to keep the temp lower when applying the film.
@cnsapam6 ай бұрын
@@geode_rc I have started printing few parts and they came out quite well. Currently editing/remodelling the pod_rib_c1 to change the hole which is for 7mm tube to fit 6mm tube (as per the relative calculation am keeping the hole to have diameter of 6.4mm). I hope thats the correct hole size for 6mm tube. Thanks again for sharing this model. Any chance if 4-channel with aileron version for 1 or sub 1meter DLG coming soon?
@geode_rc6 ай бұрын
@@cnsapam great know that you’re good at modeling. I use 0.2mm per side to compensate for the 0.4mm wall thickness in CAD. If needed, remaining thickness compensation is taking care at slicer. As for 4-ch dlg, I’m thinking about that… still long way to go though. BTW, if possible, please join us on RCGroups. It’s easier to communicate technical details on the forums with pictures/ graphics.
@patraymond37915 ай бұрын
where do you get the carbon fiber parts like the tube and flat pieces? Pat
@geode_rc5 ай бұрын
See post #2 - www.rcgroups.com/forums/showthread.php?4489525-Another-Bug-DLG-Bug-Lite-3D-Printed-LW-PLA-e-Fuselage-V-Tail
@sosq2226 ай бұрын
hi, by 2x 5gram serwos, what waight should be the battery ? Thanks for creating and sharing😁👍👍👍
@geode_rc6 ай бұрын
1S 350 ~ 500 mAh battery will do just fine. Some nose weight might be needed depending on your setups
@carolinaboy0086 ай бұрын
How do you get rid of the wall-looking thingies that are intervened within the object?
@geode_rc6 ай бұрын
Not sure which one you referring to. Could you show a picture? Or time stamp on the video?
@jo21e67 ай бұрын
Which wingprofile do you use?
@geode_rc7 ай бұрын
AG37
@phgi35937 ай бұрын
awesome . plane so elegant
@geode_rc7 ай бұрын
Thanks a lot!
@michaelsanderssa4 ай бұрын
Hi, where do i get the CG for this DLG?
@geode_rc4 ай бұрын
Please refer to lightnin bug for cg. Link to plan can be found in the faq section
@AdemirAlmeida15037 ай бұрын
Very good. Do you have any projects with ailerons?
@geode_rc7 ай бұрын
Yes… for slope soaring …. kzbin.info/aero/PL9Pbd3mrLY1V5lDbKXBP0k-YYS6rrTWCN&si=tiKJRDUT9BaTQU-k
@cakedayy6 ай бұрын
where do you get your covering film?
@geode_rc6 ай бұрын
I got mine 15 yrs ago from local hobby shop. If you can’t find light weight covering film, try thinnest doculam (~2mils). I use that on my tail feathers.
@vidmaszeАй бұрын
nice 👏 that's gonna be something to not wastefully use Bambu's most expensive PPA-CF filament on! (almost 2x stronger than PAHT-CF in some measures)
@geode_rcАй бұрын
Think about that too👍
@vidmaszeКүн бұрын
@@geode_rc really cool, even with just PAHT-CF this is already almost understuctable (used TPU for nose), been crashing to the ground without RC countless times - at least as good if not better than foam! wait until I recreate it with PPA-CF!
@carolinaboy0086 ай бұрын
What is the designing software that you use?
@carolinaboy0086 ай бұрын
I know now. I figured it out.
@geode_rc6 ай бұрын
👍
@ilyaapokin18145 ай бұрын
3mf files are broken: can not open in any program... no object or parsing error at line 21
@geode_rc5 ай бұрын
Try Orca or Bambu Studio.
@shobhitprakash7 ай бұрын
Where do I get the files for this... if you can help.
@geode_rc7 ай бұрын
Please see link in the video description for the files.
@phgi35937 ай бұрын
can i skining the wing with copypapper?
@geode_rc7 ай бұрын
Not recommended. Likely too heavy.
@Sandokans7 ай бұрын
Hello. It is possibile to put some small motor?
@geode_rc7 ай бұрын
I have an eBug with VTail on my to do list. Stay tuned.
@lebojay7 ай бұрын
If you want to print a motorized glider, there are many out there to choose from. I’m glad this is a hand-launch model; we need more of those.
@pintony0577 ай бұрын
Can you upload the files in the format stl files please :)
@geode_rc7 ай бұрын
STL only will lost lots of information needed to print. Please open the 3mf file using Bambu Studio or Orca slicer. Export the STL from there to keep the info needed for "modifiers" & print profiles. It is recommended to use Bambu Studio or Orca slicer than porting the STL files.
@pintony0577 ай бұрын
Hi, I'm downloading the file But something doesn't work for me with the file It comes in an incorrect format can you help thanks
@geode_rc7 ай бұрын
This 3mf release is for Bambu Studio / Orca slicers. Please give it a try again. Thanks.
@pintony0577 ай бұрын
Thanks for the quick response
@jo21e67 ай бұрын
Can you upload the STL please?@@geode_rc
@jeromedupont89947 ай бұрын
the bug appears a 6.30 lol Nice build TEDDYBEAR
@jeromedupont89947 ай бұрын
You design faster than we build
@jeromedupont89947 ай бұрын
seems you put more dihedral on this one
@geode_rc7 ай бұрын
@@jeromedupont8994 yes, changed from 6 degree to 10 degree :-)
@ripmax3337 ай бұрын
Do you think the normal LW-PLA can also be used (Not pre-formed) did you tried it?
@geode_rc7 ай бұрын
@@ripmax333 it’s possible but will be softer. Be cautious when shrinking the covering or use Japanese tissue.