Carburetor Problems After Removal? Maybe I can Help! A Tech Tip How To!

[@SlickTrickRC]

I tested the 38cc and it's good to go now. Your video helped twice . I realized I had the high and low needle confused. On a nitro the long screw is the high needle. But on this the long screw is the low. Backwards haha. I'm glad it is ok. I watch it for any weard issues. Then I shut it off and inspect. I hope my seal doesn't leak like you said few vids ago. I don't own a tool to remove that clutch. Seems good though.

[@SlickTrickRC]

I also referenced your video this evening to be sure. Ty bro.

[@eastsiderc]

Hey brother awesome! Its okay you me and a lot of people have confused that haha. The best way to look at is low is closest to the engine and high furthest away. Once you burn that in your brain you wont confuse it anymore. As for your seal if it was bad you have noticed right away so that fact you got it running good Is say you are fine bro. Invest in a clutch tool. DDM has very nice ones. One of my favs is the Bartolone billet one. You are very welcome and thank you for the support to the channel bro. Much appreciated 🙏🤝

[@SlickTrickRC]

@eastsiderc I love anything rc. But mostly I love Jesus. So I'm glad you share your faith boldly. Worship in truth and spirit. Amen

[@eastsiderc]

WOW brother a brother in Christ you are!! That comment was solid. I had to pin this. I love to help people spiritually and mechanically! Sharing about Jesus fires 🔥 me up. I cant hold it in. I hated to miss this last Sunday but I wont this coming. I have a good uplifting word to share!! God bless you and your family brother I appreciate your encouraging and kinds words. It means more than you know to me to see anything about the Lord in the comments especially a non service time Video. That is huge for me and really helps me want to strive and never ever give up! 🆙 🙏🙏🙏❤️✝️✝️✝️

[@SlickTrickRC]

@eastsiderc I enjoy your Sunday service time. I lost my church and can't find one that's right. So I'm just doing online church. Stay positive and thrive, bro. ❤️🙏❤️

[@robertbarrett8959]

Love the engine sound effects! Very accurate. This is great video to have as reference for the ones who struggle with turning.

[@eastsiderc]

Thank you Robert I appreciate ya brother!

[@sigma008]

Hey thanks for the video info. I got one engine running. You have one of the best rc channels bro. Thanks again...

[@eastsiderc]

Hey Christopher great brother Im so glad you liked it man! You’re very welcome. Thanks for the content suggestion! Appreciate you brother!

[@micqn2]

The Sound Effect is actually helpful at least you know what to listen to instead of trying to figure out what it sounds like.Thank You For that!

[@eastsiderc]

Thank you bro Im glad you liked it. Very soon Im going to make the engine make the sounds . I want to help train yalls ears to a proper or good enough tune to have a great time without burning the engine up.

[@rossstafford4531]

I enjoy your knowledge and KZbin videos. I have buggies myself the 5B and I have. Losi 5T 2.0 and I like your collection you show on the videos and I like your tips. You give good tips and they do help. I have actually tried a couple of your tips have helped me out dramatically mate. Hope you and the family are going well. 👍🏻🇦🇺

[@eastsiderc]

Man bro this is a great comment of encouragement! Thank you so much! Im so glad Ive helped ! I hope you and your family are blessed as well thank you for that Ross! Braaap on bro!! 🇦🇺🇺🇸🤝🤝

[@rossstafford4531]

No worries mate. Keep those good videos coming about the 5T and your other vehicles mate and hope you and your family are having a very good time. I’ll enjoy seeing you next video on KZbin. 👍🏻🇦🇺

[@doncaignou2589]

Good video young man . One of your best . That will really help people. That is propped information

[@eastsiderc]

Thank you sir! I could have elaborated much further but Im going to with actual engine sounds soon.

[@obotish1981]

Omg the sound affects really help 😂

[@eastsiderc]

😂😂 I hope they do and Im glad! I will make the sounds with an engine very soon

[@tonymanna9160]

Great tip bother.

[@eastsiderc]

Thanks brother Tony KZbin has a heart by your name now because you are a top commenter. appreciate you my brother !!

[@karlw2090]

Great video!

[@eastsiderc]

Thanks brother Karl for checking it out!

[@benjammin3078]

Thank I will try this method

[@eastsiderc]

Ah found my other carb vids I see. I really need to play list these my bad Ben!

[@benjammin3078]

@@eastsiderc lol it’s ok I’ve switched one carb for another and since it’s been giving heck but after seeing this video I will try and report back if it was successful but I noticed that the idle screw was off due to the servo not placing the needle flap where it should with screw so unadjusted accordingly and see if that helps as well 🙏👍

[@kingkongrc247]

Very good info 👌

[@eastsiderc]

Thanks bro Im glad you liked it!

[@Grandpasrcbarn]

very well explained Jeff. Great video.

[@eastsiderc]

Thank you my brother Tom!

[@soblessed6438]

Excellent tutorial! Great sound effects too.

[@eastsiderc]

Bahaha thanks mom

[@thatsmyrc]

Love the sound effects 👍🏼 awesome info

[@eastsiderc]

Thanks bro Im glad you enjoyed it

[@TheBuddylab]

Jeff, I see you use 50:1 gas oil mixture instead of the older 25:1 mixture? Can I use the premixed gas oil like the Echo fuel, Husqvarna or Stihl. Another great video and love the sound effects. 👍👍👊👊 you need to go to Hollywood and do them for the movies.

[@eastsiderc]

Hey bro you sure can use that fuel. The stihl is 93 octane and thats very good oil. VP also makes fuel premixed at 50:1 with 95 or 97 octane I can’t remember. But yes you can absolutely use those fuels in our rigs. As for a Taylor or big bore, I would go with a better quality race fuel such as VP C12. The performance you get from it is unmatched compared to the canned fuels. Hope you have an awesome day Buddy!

[@michaelgraham2943]

Excellent 👍

[@eastsiderc]

Thanks Mike appreciate ya bro

[@wolfgang4136]

Awesome👍👍👍

[@eastsiderc]

Thanks brother !

[@jukkaovaskainen]

👍

[@Js_junkyard]

Good 👍🏻

[@Js_junkyard]

I just followed these steps and it was helpful. I narrowed down my issue to the carb flooding suddenly.

[@eastsiderc]

Excellent brother excellent I’m so glad I could help. I hope you’re having a super awesome day.

[@Js_junkyard]

Thanks, man it was a decent day! I hope yours was good. Let me ask you for some more advice though? I’m using the spiral diaphragm in my 1191, yet it floods up all of the sudden, I know this because my tune was sounding okay, I barely went lean from the base settings. I drive it about 5 minutes and all of the sudden it just runs like crap. The plug looks oily but I’m also still running through the first tanks of fuel using the 927, so I would expect running that oil is going to be a little dark. The carb looks wet inside, so I’m wondering is it the little seat in there? I cleaned out that tiny screen in the carb too which helped for 5 more minutes. Make a video on how to test that needle/seat for leaks and maybe how to check adjust pop pressure?

[@kanenstuff]

Can you do a good turbo flutter sttuuuuuu, thanks for the tips always look forward to them.

[@eastsiderc]

Hahhaha! Dont believe Ive ever tried haha. Glad you like the tech tips brother !

[@michaelsoucia4983]

Hey brother Jeff hope things are going good for you. my pulse hole is oval do I have to cut the gasket to match or will be fine. Hope you have a blessed one see you on the next one crazy brother Mike is out 👍👍✌️✌️

[@eastsiderc]

Brother crazy Mike you’ll be just fine bro

[@michaelsoucia4983]

Thanks brother Jeff I can't remember if I cut out the hole bigger or not probably did because I was watching your video on the 38cc or 40GT When I was doing my 38cc. your input means a lot to me thanks again you the man Crazy Brother Mike is out again 👍🙏

[@swaggerconcepts]

Great video! What temperature should I run a 36cc when tuning and when ripping around? Another video you did at your moms house you kept checking the temp, what should I be looking for when tuning in relation to temperature control on the engine, and with warm, hot, or cold weather? Thank you!

[@eastsiderc]

Hey bro thanks for watching. Hot weather the engine is definitely going to run a little warmer. I dont even run this heat honestly, you have to take away so much fuel , the engine gets hot and dont make enough power for me. But honestly no matter what you should see operating temperatures at the cylinder near the base of it 190~225 any hotter and your heat soaking the engine. Running in hot or cold wont hurt a thing its just a different tune needed. Warm up I take off when I see 115 degrees and then I drop the hammer wide open. Clutch temps should be between 90~160 depending on how much off n on your doing with the clutch. I do a lot of gear changing so you probably saw me taking clutch temps as well as engine temps. The temp gun is just for checking. Your best tuning tool is your ear! A trained ear will hear a to lean of a tune right away and make the adjustment. Temps at the head are much higher because then you will read combustion temps. But dont be scared if you see 245 after beating on it in the summer heat it should cool back down rather quickly if you got the right amount of fuel and oil mix going through the carb. 50:1 makes things much easier for tuning and cooling of rhe engine. As more fuel get to the engine and fuel cools not oil however with more fuel you get more oil because of the oil being suspended in our mix. Hope that helps and I didn’t dump to much on ya.

[@SlickTrickRC]

I just posted 2 videos on my channel about this exact problem. Sorta. I have a 30%n clone of losi5t. Blue like yours. Same nasty spike tires also. Mine kept having problems idling. Then I thought I had it. Then realized it was the screws on the intake had loosened. So I had trouble getting it to hold a tune . Then it started to idle high. So then I shut it off. After checking it out. Found the intake bolts loose. I didn't use much thread lock . My bad. So I kept setting it back to stock settings. Thought it was 1 1/4 and 1 1/2 turns for settings. I got the zenoah 38cc race engine from fearless. I think its a 36cc thats modifiedto 38. Not sure.. Think I'll try your suggestion as soon as the rain let's up. I always go back to stock settings if I have any issues. Thanks for the tips. God bless you bro. Ps. Avoid all false profits. Haha. Absolutely. I met one. Avoid at all times. God bless

[@eastsiderc]

Brother thanks for the great comment. Hopefully you didnt get a lean issue and hurt the ring n piston. When the exhaust or intake comes loose the engine can go real quick. Usually if you catch it fast enough youll be okay but you gotta notice it quick. The 38 is a chinese 30 degree north engine and its made of high quality materials . Very good engine that is not done right lol. God bless you brother any help you need just ask bro! If you need me to make a video for you on something just let me know Im very open to suggestions and I LOVE helping people its Christ in me!! God bless you and your family brother! Thank you so much for the channel support!

[@SlickTrickRC]

@@eastsiderc it went lean and idled high. I shut it off. Should be good. I was kinda of expecting a gasket leak. Ty bro. I will be testing it tonight after work 😎👍

[@blowingsmoke4474]

Ding ding da ding ding ding 😂

[@eastsiderc]

😂😂

[@karlw2090]

I didn't know some of these were one time use gaskets

[@eastsiderc]

Yessir! Crush once and chuck it, its very obvious once you remove it youll see the silvery part of the gasket on the sealing surface and pulled apart from the gasket itself.

[@scottvahey4869]

Hey Jeff, I have a 45 cc and I want to change the manifold do I change it to a G320 manifold

[@eastsiderc]

Yes brother you sure do the manifold. I’m using here in the video is the G320 Zen manifold I highly recommend it.

[@john1999-ew1jt]

Hello there, I'm trying to fit a 38cc head into a 28mm stroke g320 today, but I discovered that it has a free port after the exhaust had a 0.040 squish at the top dead center. The 38 head has a 2.31 mm free space to the head with the gasket installed; if I remove the gasket, the gap will be 1.91 mm, requiring me to cut 1 mm, to set 0.040 squish but I want the 0.020 squish. but the issue is free port Do you have a solution for this problem? Many thanks for that

[@eastsiderc]

I sure dont John. The only way I would say is to end mill the cases and or the cylinder. Sometimes a little free porting is okay. I know that 38 head has a bit of room for sure and a very tiny exhaust port. But made of quality material a great “porters casting” good luck to you bro thanks for watching. Sorry I could not be of more assistance.

[@john1999-ew1jt]

​@@eastsiderc Thank you for your kind wishes. I really appreciate your help.

[@eastsiderc]

@@john1999-ew1jt you are very welcome bro!

[@JavierG911]

Let gooooo

[@stevenpeters2593]

Jeff, One big plms how a deaf person can't hear the motor running high and low and also more gas. How? Hard for me!

[@eastsiderc]

Well brother you are going to need to use your other senses. Set the base settings and feel the engine if it feels like its revving high in the first start follow these steps here and you should be happy brapping. God bless you brother Steven. If you lived close to me I would tune all your rides for you so you would not have to worry about a thing!

[@ronniesrc]

I have a question can you put a 32 cc cylinder head and piston on a 30.5 cc engine

[@ronniesrc]

I just bought a red cat rampage XT

[@eastsiderc]

No sir you sure cant the cases are different

[@eastsiderc]

Congratulations on your new RC Bro

[@eastsiderc]

Fearless RC bro Zen 32 complete engine 299.99 cheap! And a great engine

[@ronniesrc]

Thank you for answering my question and I’ll watch all your videos

[@pwoodpimp23]

Hey brother I was wondering if you could help me out with something my 45cc my brand new one just like half locked up and only spends halfway pissing away half of a revolution I was wondering what's better the 45 CC with the twin rings or one of them 11 horsepower 32 cc pro with the Reed's case

[@eastsiderc]

Sorry bro, my reply never made it back to you so I’m gonna re-reply now

[@eastsiderc]

Hey bro, the single ring 45 is much better and the 32 read case definitely does not make 11 hp seven at best. Check your clutch it could be loose.

[@pwoodpimp23]

Thanks for replying the 45 I have is the duel ring I checked the clutch it's good it's like if you had a piston stop tool in the plug hole spin half way and hard stop the other way half way clunk hard and absolute stop out of the around $300 range engines which do you recommend it's a 5B on steroids probably closer to a 1/4 scale now and it's built to last it's heavy

[@eastsiderc]

@@pwoodpimp23 you’re welcome buddy! I well you cant go wrong with a zenoah g320 its a great engine and when paired with the Taylor side pipe its a lot of fun and pretty snappy. Second would be the 30 degree north 38cc I really like that too. It makes even more power but there are some things you need to check on it first .

[@eastsiderc]

You need to pull the head off that dual Ring and see whats going on. Remove the lower ring and save it. You may also have a bad crank bearing

[@buzzedalldrink9131]

its how to not how too The thumbnail could lead some in to believe you don’t know what you’re doing, without even watching

[@eastsiderc]

😂😂😂 its all good thanks for policing my grammar I fixed it for you! 🤝

[@buzzedalldrink9131]

@@eastsiderc just wanted you to know, could happen to anyone. thanks for the video

[@1ken.cheniergmail]

Thanks for the tips ..See ya at the next one today ...Jesus time my brother ..

[@eastsiderc]

You are always welcome brother Ken! Bout got your goodie bag wrapped up. I want to add one more thing 😂.

[@1ken.cheniergmail]

@@eastsiderc You are to kind my man !!! Thanks so much ..