2007 Escalade HID Headlamp Bulb Replacement

Also Visit our webpage at www.carrepairsm....
Facebook at / carrepairsma. .
Twitter at / carrepairmadeez
And Forums at Forum.Carrepairsmadeeasy.com

[@raebeez7765]

Thanks for the video..I was able to replace my bulb by myself and I’m a 53 year old girl😃🔧🔩🧰💰

[@jdubboy580]

5 yrs later an still helpful I needed this shop tried to tell me 2hrs wow thanks bro

[@chrislevine3031]

Thank you so much for posting this...you really made it easy for me to follow...and believe me when I say...I am no mechanic. The dealership wanted almost $125 to change this and then $292 for the bulb....I got the bulb at Autozone for $97. Thank you very much..!!

[@wb.conner6444]

Very easy to follow video. Great job! Excellent instructions and very simple to do. Followed this video and replaced bulb in about 15 minutes!! Saved money to have this done. Thanks guys!!! Great job!!!

[@justsaved3876]

Thanks for sharing that, I have a 2007 Cadillac Escalade ESV and my HID bulb is our on my passenger side. The dealership wanted to charge me $400 to change two bulbs they were charging me almost $200 a bulb, but i can get a pair for under $100 and have someone install them for me. This video has shown me I can do this myself...Great Video

[@ericrobinson4644]

Great video walk me straight through it in a time of need heading on a road trip the night before my headlight goes out ran to my local store pick one up put it in and 20 minutes at most you're the man keep them up

[@matthewyeager2000]

Thank you! This video made changing mine very easy this afternoon.

[@clearedhot6146]

You can also get access to the light through the fender well, but you'll have to remove the front tire of whatever side you need to replace

[@mrslrj1s]

I just changed mine today!! Thank you. You saved me on labor costs.

[@fredbowling7968]

Is there a difference between the right bulb and the left bulb? Is the left bulb low beam and the right bulb high beam or vice versa?

[@travelingworld5649]

What if new bulb wont lit up even after check the fuses , do you think i need to check the ballast and replace them to a new one

[@urieldominguez8363]

Good video and the other side .how much for the lights ?

[@MarkkuDrummer]

Great video. Soon I'll be getting my 2008 Escalade from the car dealer. One question, is this way faster/easier than the route from the grill? I mean taking the grill off and taking the headlight all the way off?

[@williamwhitehead8362]

What would you do if the ballast was bad at this point as you put in the new Bob at work but what if it didn't work then what were you do?

[@CarRepairsMadeEasy1]

Lance...unfortunately we do not have a video of the drivers side. If I remember right it should be easier to access if a similar way. At the auto parts store just tell them you need H.I.D. bulbs

[@Diziyer25]

God BLESS you!! And mine is out on the same side and I see the same reoccurring trend w/ the Escalades. Passenger side. This is easy enough because what the shops are charging is ROBBERY!!

[@bigtime4698]

Your video was great you really know what you talking about and made my life a lot easier

[@FHILLYBULL-j7s]

Now this is how you explain a DIY project.. thx👍🏼

[@AngeloBarela505]

Where did you buy the bulb from.?

[@LanceKorsun]

Awesome Video. Do you have a video for changing the drivers side bulb? Also, what's the name of the bulbs I should get from local auto parts store? I have a 2007 just bought it so I'm trying to learn.

[@kiarraguzman692]

how do u replace the driverside

[@shareevanbeekum4529]

Fantastic tutorial. Watched and repeated, new lights installed without tearing the entire front end apart. Definitely subscribing.

[@dustinwallace8490]

Just finished changing my headlight thanks to your tutorial. Only took about forty minutes and that was in the dark with a flashlight.

[@brianvan67]

SHOULD NOT TAKE FORTY FIVE MINUTES TO CHANGE A F'N LIGHT BULB!!!

[@brianvan67]

That is not directed towards you, it's bull shit that it's that difficult.

[@13579jdr]

Nobody ever does the left side. Why?

[@ranman4481]

Thanks for getting straight to the point!! 👍

[@PhinheadLR]

Unless something drastically changed, you pop the two plastic rivets on the radiator shrowd, pull the two metals pins on the light assembly, and the assembly pulls out. It's designed to be changed in about 3 minutes, no need to remove anything in that video.

[@11MikePlazek]

You clearly haven't worked on an Escalade lol

[@Tulitaratch]

It was like that on the older chevs,

[@slidog24]

Thanks. Spent $100 on the new bulb and didn't see an easy way to change it.

[@sperez6140]

Very good video but you did not have to take apart the air filter all you have to do grab it and push up and the whole thing comes out👍

[@golf-n-guns]

Just noticed condensation and a burned out bulb in the driver's side assembly in my 2008 Escalade.

[@Africa2DaWorld]

This video makes it so much easier changing that 🔥🔥👌👌

[@halcraw414]

Great information. Your details saved me time and money.

[@richardluna1279]

Excellent information nailed it👍

[@MrJBM247]

Got my bulbs on ebay but made sure they were brighter than OEM. Think they were 5000K lumens. Don't go over that because the higher the number, the more the color will change (blue, purple, etc), but more importantly, it impairs how far ahead one can see. Hate how yellow the OEMs are, including the daytime running lights and the top bulb. Changed all of my bulbs to bright white and not those dingey yellow ones from the factory.

[@aurelioordonez7313]

please tell me how to change on drivers cide

[@Bryson300]

this video sucks it 1000 times easier to remove the full headlight assembly that way you can replace any blub on any side and itll go in and come out the same way both side super easy there is only 4 bolts that hold it in just remove plugs in grill to loosen the grill to pull the headlight out

[@coreysmith2196]

@@Bryson300 how many tabs did you break🤔🤔🤔🤔🤔🤔

[@Bryson300]

@@coreysmith2196 none man its so easy just use a flathead screwdriver to pop the tab out of the lock then just pull it out thats all I had to do it was unbelievable how easy it was

[@derrickrussell3276]

What model bulb did you use ?

[@mstahoechik]

hey John. this is also the same on 08 model right? and should I buy from dealer, or online since it's cheaper? what exactly to buy, ballast with bulb extended out of it? cuz since I've seen on amazon are just a flat piece with nothing on the end, does it matter brand, and if so what is the original brand, Is it ac delco? sorry for all the questions loll just freaking out cuz a friend of mine told Me when this happens they'd have to take my entire bumper down and it'll cost close to $4/500 for everything! please say it ain't so!

[@derrickr30]

mstahoechik (HAIR BY SHARCARIN) What did you end up buying? Which ballasts? Did you change all the bulbs with a ballast?

[@schoolie78]

What is the name and model number on that bulb that came out? I need to replace mine.

[@rudyramirez5425]

did you ever find out

[@OnlineRealtor]

Hello Friend, your video is great. I got to the bulb following video, however, the bulb currently installed has a circular end and I cannot twist counterclockwise. Any idea how to take these circular metal end bulbs off? Also, the electronic connector (plug) connects directly into the bulb via 1 wire (in other words no ports on the bulb enclosure). The only thing coming from car is 2 wires - yellow and black wires that came off with each having small metal tip connector which connect to the end of the bulb’s plug. Also, I noticed there is no retainer clip. I see all the metal which the retainer covers when on. And the last, there is an orange glue type around the metal which is normally covered by the retainer clip. I’ve attached a link which shows pictures. photos.app.goo.gl/saHtGJJzTDASQH9o9 Thanks.

[@alexmma1]

Thanks for the video, it was ver helpful.

[@bigtime4698]

what happens if you change the bulb and the light still doesn't work

[@williestonejr.6024]

Jayvon Thompson the balancer probably has went out also

[@travelingworld5649]

After change the bulb if it still wont work Then check fuse and if fuses are good then definitely your ballast of headlight go bad. is the another main reason as well u need to replace them .

[@laryrobot2588]

This is a Very Accurate Video.. Thanks

[@joannmesquita7042]

What if the bulb doesn't turn

[@shanra4764]

Thank you your video helped me.

[@kirbyross7140]

the video was very helpful thank you

[@AlanTrades]

Why do they make it harder and harder to change a simple bulb? I noticed it’s practically the same for all gm vehicles where you should just take off the bumper and headlights to gain access to a bulb lol

[@johnsimmons6467]

Brilliant, really usefull video. 👍

[@brandenwilson9502]

Great video. Thank you so much!

[@frogetmoney]

Great video... thanks🤟🏾💯

[@lf3566]

Great video!👍

[@scottpeary]

Great video! Thanks!

[@notavailible8044]

Um.... why wouldn't you just take the entire headlight assembly out since it is literally just 2 bolts and a couple clips?

[@RaininMortars]

all that for one little bulb....geeez...what a pain in the ass

Nice job, thanks .

[@richardmckinnon6749]

Good job 👍🏼

[@INFINITY1664]

Ur video was helpful. Keep it up

[@mujjuman]

wow so we dont need to remove our whole front end

[@MichaelBenninger]

Great concept

[@jaybee5775]

Its easier to just take the whole headlight assembly out from the front. Imo

[@BIGDOGS05]

Thanks a lot

[@alancornwell5559]

Now do the drivers side instead of the easy side.

[@travelingworld5649]

Driver side is actually much easier than passenger side

[@expatconn7242]

great vid ...thanks

[@waynehayward4304]

That was a good video....thxs

[@sergioramirez725]

That has nothing to do with the heat light lol 😂

[@rushnash3]

Again the engineers that make this shit don’t make it easy to change a dang light bulb

[@rcaldwell56]

Cadillac Escalade Ballast Completely Eliminated, Watch. This KZbin Video Is On Google.

[@ralphfactor579]

Great

[@mrslrj1s]

Omg. Getting it back in is the worst