Castle Creations Torque Limiter For No Prep Drag How To

[@taylorrc6082]

Great content bro! There isn't enough info on how to setup Castle No prep cars out there, I appreciate this a lot.

[@RcFunDrizzy]

No problem and appreciate you tuning in definitely more to come for sure just trying to figure some more things out

[@nolimitrc1]

Listen up guys dre put up a banger nobody has any good info on torque limiter on the castle its actually a game changer and is like turbo on a maclan with your m17 imo 11 is perfect

[@RcFunDrizzy]

Appreciate you bro and definitely can’t wait to have some more fun

[@Mauler5000]

Thanks for the information! I was glad to see you did this with a spectrum remote. I will be using the same and didn’t think I would be able to really tune anything.

[@RcFunDrizzy]

Not a problem and glad I could help

[@blacq83]

Thanks for the information great content I'm about to take the Tekin RX8 out of my front wheel drive drag car and put the Mamba Monster X back in

[@RcFunDrizzy]

Any time appreciate you tuning in let me know how it works out

[@robschierbaum]

Great info bro. Nice job.

[@RcFunDrizzy]

Appreciate that and thanks for tuning in bro

[@islandrc-duke1972]

awesome rc and great info brother

[@RcFunDrizzy]

Appreciate that brother thanks for tuning in

[@oscarvelazquez2128]

Great video man thanks

[@RcFunDrizzy]

No problem thanks for tuning in appreciate it

[@reallythough4591]

Appreciate you taking the time, thanks. Any recommendations on a 7700tp and copperhead 10 in a carbon drag slash? I've managed a 2.90 at 51, but car should hit 80. I'm wondering if controller is in training mode, but can't figure how to change on tqi receiver, as it's not running the velineon ESC. I'm tracking straight, running 20t to 90t spur, but my throttle doesn't accelerate past around 3/4 trigger.

[@BrowardBikelifeTJ]

Could I run the test with pinion still connected and wheeels spinning

[@RcFunDrizzy]

I wouldn’t it will blow the tires off best to take it off

[@brandonpage2658]

When adjusting with the radio. Do the aux trim increments need to be set to a certain amount. Or just 1

[@RcFunDrizzy]

You can put it to whatever you like

[@callmekev0h]

I got my mamba monster last week, waiting on my 14series motor. Did u have to do big pinion small spur like castle recommends ?

[@nolimitrc1]

You need the opposite actually

[@RcFunDrizzy]

I would say yea they recommend FDR 7.8 car I’m running is at 8.1 still gets it

[@blacq83]

If I'm using my radio to adjust the torque where should I leave the setting in the ESC? Minimum or Max?

[@RcFunDrizzy]

That would be up to you you’ll have to see how much it can take

[@blacq83]

@@RcFunDrizzy I guess what im asking is do I need to do anything to the esc besides set the torque to custom and enable the aux?

[@RcFunDrizzy]

@@blacq83 nope you can add more torque or less by going up and down on that number of torque in esc

[@dadon197922]

@@RcFunDrizzycan i maximize my torque on the esc and bring it up and down on my futaba radio

[@PhilHenzig]

Thank You!

[@RcFunDrizzy]

Any time thanks for tuning in

[@frisos3944]

Good to know. Does it limit the torque through the entire rpm range?

[@RcFunDrizzy]

It dosent only off the start

[@frisos3944]

@@RcFunDrizzy any different than punch then?

[@RcFunDrizzy]

@@frisos3944 most definitely this will get you off the line every time if setup right

[@OswaldBeef]

@@frisos3944 yea thats what i wondered. how does is this different from punhc. GOnna have to play with it to find out ;D

[@frisos3944]

@@OswaldBeef i’ve gathered some experience with this lately. I assigned torque control to a dail on my controller. In my experience it only limits the torque. Top speed is the same. It only takes longer to reach top speed. Punch is only from a standing start. Once you’re rolling it’s torque control.

[@gregory.acarty-lake6181]

u can test with any voltage?

[@RcFunDrizzy]

You can use with any voltage

[@RcFunDrizzy]

I would only use a 2s on small motors

[@nolimitrc1]

You guys doing the points race by the college?

[@RcFunDrizzy]

Yep you know it

[@melvinbailey1248]

How do you set it up on the m17

[@RcFunDrizzy]

Same way as the Remote in the video just have to find the way in yours to setup the 3rd channel

[@RcFunDrizzy]

With M17 you shouldn’t need it

[@melvinbailey1248]

Thanks man i realized i did not need it just got the remote