Keep Your Minn Kota Ulterra PROBLEM FREE (Troubleshooting and Maintenance)

The Minn Kota Ulterra trolling motor is the best trolling motor I've ever owned. I've been running the Minn Kota Ulterra trolling motor on my catfish boat for 3+ years and had two different motors and haven't had one single issue. I've had a lot of people reach out to me that are having issues with their Minn Kota Ulterra and like most other marine electronics issues the problem is usually a bad installation or operator error. I've yet to touch one single motor that had issues that were a Minn Kota-related problem. In this week's video, I'm taking a deep dive into the Minn Kota Ulterra and how to make sure you won't have any stow and deploy problems with your motor. Its simple stuff, good clean installs, and basic periodic maintenance will keep you up and running with no problems.
Timestamps
00:37 How to keep your Minn Kota Ulterra problem-free
1:01 Stow and deploy issues because of an improper install
03:25 Ulterra maintenance for problem-free operation
03:35 Keep the track tight (the most common problem)
04:35 Lubricating the track
05:30 Lubricating the latch pins
06:00 Lubricating the internal mechanism
Trolling motor plug - gocatfish.in/3eSbbYb
Most Recent Upload ► goo.gl/wGwdlT
Most Popular Video ► goo.gl/27gAIF
*****Get more catfishing tips and information*****
www.catfishedge.com
*****Get official Catfish Edge gear, ebooks, feature length videos and more*****
www.catfishedge.com/products/
*****Fish with me*****
www.txcatfishguide.com
www.catfishedge.com/catfish-e...
*****Products I Designed*****
► Chad Ferguson Signature Series Rod gocatfish.in/CFCatfishRod
► Versa-Rattle Catfish Rig Rattles gocatfish.in/VersaRattle
► LockJaw Catfish Fishing Grips gocatfish.in/WSTLockJaw
► T3 Triple Threat Catfish Hooks - gocatfish.in/T3Hook
► Digital Catfish Scales - gocatfish.in/CatScale
*****Sponsors*****
►Whisker Seeker Tackle: gocatfish.in/2iiJWeO
►SeaArk Boats: gocatfish.in/2iiFSv9
►Abu Garcia Reels: gocatfish.in/2iiCxfk
►Humminbird: gocatfish.in/2iiEecQ
►Minn Kota: gocatfish.in/2iiKb9I
►Driftmaster Rod Holders: gocatfish.in/2iiPXbx
►Fitec Cast Nets: gocatfish.in/Fitec
►Some links in the description are affiliate links so you if make a purchase I receive a small commission on the sale, it doesn’t cost you any money and the proceeds from your purchases help to support my efforts producing these videos for you.
*****Connect****
Subscribe if you like watching!
Have questions, want to see more, suggestions for more videos?
Twitter: / catchcatfish
Instagram: / catchcatfish
Facebook: / catfishedge

[@scottvan6064]

I've been using my unit for four years and never did any maintenance, BUT that changes today. Thanks for the tips

[@seanmoore5300]

Nice video. One thing I would add is that if you are replacing an older motor with a new ulterra, make sure that you have a properly sized circuit breaker. Found on my boat that the previous owner had a 40a breaker installed and the 24v ulterra calls for a 60a. This most certainly caused my random shut offs under heavy load and most likely the one stow error I had.

[@ronaldfoster2954]

Great video. The best Ulterra user video I’ve found on KZbin. I just completed the install of my Ulterra and still need to put it in water too check everything. I can’t check the deploy and trim until I get it off the trailer due to crank clearance.

[@marquiblaylock3551]

I love my Ulterra trolling motor. Never knew I could tighten the track, thank you.

[@Catfishedge]

Thanks!

[@bradbernst1113]

This video was extremely helpful and informative. I have had my Ulterra for 3 years. Last season it started having problems deploying and would stop and show motor error. I brought it to the Minnkota service Centre in my area. I was told just to clean the shaft with armor all wipes. I asked about preventative maintenance etc. After paying the $100 bill for them to wipe it down it has continued to give me problems frustrating me on the water without my trolling motor. I just completed everything you mentioned from the tension of the belt to the lubrication. It is now deploying and stowing without issue. Many thanks.

[@Catfishedge]

Glad it helped

[@jerryronke6434]

Thanks for sharing! After seeing all the reviews stating deploy and stow issues I was reconsidering purchasing an Ulterra. Now after watching this I'm sure most are operator errors, and the Ulterra is trolling motor I'm purchasing.

[@brianwathen5285]

Great Video‼️Just bought a new Ulterra and this will be super helpful over a long long life with a well maintained unit! Thanks Chad!

[@Begohan1234]

I've had two ulterras, an older one (still with the new remote) 80lb, and a new 112lb with the down imaging built in, have had 0 issues so far except the other day after 80 hours of use with this new one it wouldn't deploy. I wiggled the shaft and it kind of released like it was binding and then it's worked perfect since. Had no idea you could tighten the track, and didn't know what to grease either. Appreciate the video.

[@RobaloRick]

Great video Chad! I ran into issues right at the end of my coast trip. I watched this video and fixed my problem. I cleaned the track and adjusted the tension on the belt and all checked good! Thanks... 😊👍🏻🎣☕️👊🏻🌊🦈

[@Catfishedge]

Glad it helped!

[@danosborn123]

Just bought a very little used Ulterra. Selling my Terrova now. Been wanting one for several years now. Very excited. And thanks for the tips!!!

[@Catfishedge]

Great to hear!

[@rippinglipsadventures]

I appreciate your video and have watched it a number of times. I'm currently working on a step-by-step tutorial video on how I launch my boat with the Ulterra. One KZbin tip I can share with you... take your first zero off the time stamps you put in your description and KZbin will auto-generate actual cut-to positions for your video. You have 00:37 and then 1:01 and 03:25, etc. If you only have 0:00 to start, then 1:01 and 3:25 and that same format after, it will recognize it. Great video and great information, though! Thanks again for the video!

[@zachparton4870]

Good info. My dad has one. Had stow/deploy error. Lubed it properly and it works better than new.

[@Catfishedge]

Thanks

[@mohamedelgohary7774]

I love my Ulterra and you made such a great video. I added your video to Bass pro shop review section. Thank you so much

[@Catfishedge]

Thanks

[@mixmastertoronto]

Thanks so much for this video. Been having deploy issues all summer.

[@Catfishedge]

👍🏻

[@catfishstalkeroutdoorswith530]

I am upgrading to the Ulterra Thanks for the video!

[@Catfishedge]

Thanks

[@thomasstott3929]

Thanks for the troubleshooting tips. I bought my Minn Kota Ulterra 8 months ago and was used very little the first 4 months. It was great until 2 weeks ago and would not stow. I had noticed that it sounded louder while deploy and stow process over the past 6 weeks. It was repaired under warranty by authorized service dealer and he replaced the trim assembly and told me it was caused by water in the head. I asked why head is not sealed to keep water out, but he said water will get in the head. He suggested to deploy and stow after wash down to drain the head. I do wash down the unit each time I come in from salt water but have never raised unit to drain head. I am also going to get some 100% silicone spray to try your tips.and hope this keeps me away from the service dealer. I had the Terrova I pilot before getting this unit last October and really like the I Pilot, but now I am thinking I should have stayed with the manual deploy and stow from all the problems I am hearing about the Ulterra.

[@sydquinn8995]

I was told that are small holes to drain any condensation on the bottom of the head... and... NOT to spray a strong stream of water pointing directly at the underside of the head.

[@Tracy.Lynn2.0]

I am loving your videos! For a lady angler I can follow along smoothly.

[@Catfishedge]

Great to hear Tracy!

[@gmermaid1]

Thinking about buying an ulterra. Read about problems however your video is excellent and I feel much better about buying one. Tom Greene

[@Catfishedge]

Thanks

[@paulwilliams2603]

Good video, I too have been running the Ulterra for about 4 years now. I hear people comment to me while I am at the ramp or on the water that there is to many moving parts and the motor will someday leave me abandoned on the water. Well it hasn’t happened yet, and I love this motor. Thanks for the tips on maintenance. Hopefully it will lead to those naysayers reevaluating their resistance to a magnificent machine.

[@Catfishedge]

Thanks

[@Catfishedge]

Thanks

[@antonioreid4867]

Ive stop using mine for 5 years... i just gave her a deep clean oiled her up and added new wires new batteries 3 weeks ago and she works like new 😍I fully recommend Minn Kota Products

[@rookiehooksetslt3352]

Thanks for the advice 👍🎣

[@kyleherrman136]

I have been running a Ulterra for 5 years, best trolling motor I have ever had, zero issues.

[@Catfishedge]

Thanks

[@jameyjacade28]

I wish I had the same experience, mines two months old and had three issues so far

[@eldonpulfer3515]

Had one on order but read the terrible reviews on the Minn Kota web site and promptly canceled it. If they offer a 5 year warranty i might purchase one in the future. $3500 after taxes is way to too much for this unit that gets 50% bad reviews. I'll just keep rebuilding my terrova for now.

[@richardbailey3065]

Very informative thanks

[@ronniedonaldson6796]

Great info! Thanks!

[@joeadams3105]

Excellent video, thanks for the details

[@Catfishedge]

Thanks

[@matbob7249]

0 problems since 2017 brand new. Sold for life

[@barryech2010]

nice job!~ very helpful. Thanks

[@Catfishedge]

Glad it was helpful!

[@LifewithAaronArnold]

Thanks for the tips!!!

[@Catfishedge]

You bet!

[@malcolmzoll7613]

Great information thanks for information

[@Catfishedge]

Welcome

[@Toonseskat]

I've not been so lucky with my Ulterra Riptide. First one was in the shop more days than days on the water. Factory replaced my nearly 2 year old motor with a new one. It's lasted most of the summer before quitting. It's going to the repair shop tomorrow. Use in salt water is much harder on equipment than fresh water. Fantastic when they work, a pain when they don't.

[@12restoration]

Hearing stories like this is why I'm leaning more and more towards the Terrova

[@Catfishedge]

Maintenance is key

[@lmbarrelracing1487]

Strangely enough, my Ulterra quit deploying yesterday while on the lake. Took it to Brian at Sartin’s today. Problem was that the main shaft and the ramps where the motor reaches the stow position needed cleaning and lubricating. I’ve had it since Sept. and don’t get to go that much but when I watched this clip I made a mental note about needing to schedule the lube maintenance routine. Just waited one trip too long. But, thanks for the video. 👍👍

[@Catfishedge]

Thanks

[@jeffdomrude9896]

Your video is the best I have seen so far. Here is my issue. I have the 36v ulterra rip tide and had stow issues last year and they replaced the mother board due to issues. I have put about 5 hours on the new mother board. yesterday the motor stopped 6" vertically during the "stow" function. The shaft is clean, belt is tight and I still had good power left on my batteries. The motor will still trim up/down but will not complete the stow function. I have done the 3 fast push of the power button reset. My unit still will not stow 100"% to the horizontal position from 6" from power head placement. Do you have any suggestions as I am on vacation and still have 4 days left to fish. Thank you, Jeff

[@fishonalbertaoutdoors9761]

Love your video and I agree it's the best trolling motor I've ever owned and by far the coolest. Just stored boat door the internet and miss it already lol. Made a short videoon my channel of using it after launching boat. Thanks for the great video

[@Catfishedge]

Right on!

[@glenndaugherity6187]

I’m running my 2nd Ulterra and really love them ! My new is a Gen 2 with the improved spot lock but the other day while fishing and stowing and deploying it numerous times it started sticking when going to deploy and I was getting the error alarm. I could just shut it off and turn back on then when I hit deploy I’d have to push on the head to get it to start deploying. It seems as if it’s sticking. It worked perfect up until this.

[@Catfishedge]

Needs maintenance

[@glenndaugherity6187]

@@Catfishedge yes did something’s you suggested and it works perfect now ! Thanks !

[@mikegrell1298]

Chad. Thank you very much for its late March and we have some open water. Tips and tricks for the ultera. I have one on order and awaiting for the dealer to call me. Im replacing the terrova ipilot that came with my lund new a few years ago. I will replace the current 12v plug with one you suggest and pm it before using. Again thxs always a good job.

[@jacqueschopin7366]

thank you for the infos!!!

[@Catfishedge]

👍

[@gilb5710]

Thank you Great video!

[@Catfishedge]

Thanks

[@Catfishedge]

Thanks

[@vindeiatrix]

Great video. But how do you check that your plug supports the right amperage? I just have whatever stock plug comes with a 2022 Tahoe

[@edernest3996]

Thanks for the video. I have a new ulterra that I have used a few times. The last couple of outings the motor has stopped while in the spot lock position. If I turn the motor of and back on it will work as normal again. The motor has been synced and otherwise works fine. I had a Terrova previously and had no issues with it at all. Any suggestions? Thanks.

[@outdoorguy4u2]

Good info, thanks for sharing. From time to time I will be fishing up the bank and have my Ultera just shut off and I will press the power button and it will stay on for a few seconds and shut off again. I can leave it alone for say a half hour, do a reset and it will work fine for months and I will not have a problem. All connections are clean and good. Any ideas? Thanks.

[@jackmanjls]

Really good tips. That's a fresh water TM...go to saltwater and the game changes substantially.

[@Catfishedge]

Motor functions the same

[@JCASTELLUCCIOJR]

Riptide has SS components which Terrova does not!!!

[@tommwarneke396]

Shopping this motor! Collecting info. Errors? When given an operation error, are these all or mostly resettable on the water? Like what must one do if they get an deploy error? Thanks

[@lenefuimaono7595]

Great video good tips. Is there any recommendation about a support for the shaft from bouncing up and down going down the lake.thanks

[@Catfishedge]

I don't use a stabilizer.

[@JCASTELLUCCIOJR]

Prevent the “HEAD” portion of the unit ftom bouncing!!!

[@davidlee1216]

I can’t seem to find the plug you are using. Do you have a description of it?

[@tombrown106]

What plug do you use?. I could not find where you said you posted it.

[@captkd57]

My troll motor will go to the left but not to the right. It works perfectly well when in spot on/anchor mode. What do I look for?

[@maddmannziggy89]

So I have had a bunch of problems with mine and bass pro is jerking me around so I had to reset my ulterra and it will now stow on the deck but it will not pull up onto the trough! It lacks stowing about 6” any thoughts?

[@jamesyates5191]

Have you ever had or heard of the trolling motor not turning on when the unit is fully deployed? I have had an intermittent problem with my Ulterra 24v Gen 2 with new batteries. I have done the reset as directed by the factory and no go. While bench testing this I noticed that if I hit the trim module the motor will start turning. Is there a way to service this unit to check for poor connections?

[@chimme11111]

Hi, nice video (y) good tips and as being technician myself I also use WD40 and grease up the moving parts. Have my ulterrra now for about 3 years and never had any kind of problems with it.. When it should break or fall out I wouldn't hesitate one second to buy another one. I have a question for you .. should you calibrate (making 2 circles with the boat) each time you get on the water? or does the minnota remember these settings? Thanks and keep those helpful vids coming!

[@Catfishedge]

Only once

[@pault5816]

How do u check for voltage drops. Because I have had nothing but problems with my ulterra. ,

[@Majeskty]

Minn Kota confirmed to me they recommend ‘Pledge or Bow Wax’ for lubricants on the shaft and belt. Both are used because they don’t attract dust/dirt. The worm/screw drive light coat with ‘marine grease’. I would recommend a 100% synthetic grease for same reason, I have heard it does mot attract dirt like a petroleum based grease for my firearm cleaning and lubrications.

[@Catfishedge]

Manual says silicone

[@chachi5975]

@@Catfishedge the Minn Kota maintenance video recommended water based silicone, I didn't know such a thing existed!

[@fishmojo865]

Do you recommend bracing the head while trailering?

[@DanielRodriguez-ex4gx]

Just got a used ulterra and it pivots to the left intermittently. I have to press very hard on the foot pedal in order to get it to pivot. Sometimes it takes several foot presses to work. Ideas?

[@SCBullterriers]

How can I get one of those hummingbird and minnkota banners???

[@Outerrythem]

My issue is that intermittently, the unit will not deploy - can hear a motor whirring, the i-pilot screens reads "deploying" but nothing happens. Turn it on and off several times and/or leave it for a few days and then it works again. Licensed technician cannot see any issue (worked for him every time). Could this be some kind of issue with the magnets? Unit is under 12 months old.

[@kathrynglasco806]

When stowing my motor doesn’t quit spinning until it tightens the cables up on the shaft and then goes into a fault what should I do?

[@JerryChanD]

I am Riptide Ulterra user. Just to note for everyone about the top of the steering bucket there is 2 connection for the trim module, both positive and negative connection, you need to know the silicon spring under the connector is in good condition = had good elasticity. If your Ulterra getting some of the electrical noise when you deploying the motor, that is the symptom. You can also notice an electrical spark between the trim module and the steering bucket at dark or at night when this occurred. I found this may be the reason why I failed my mainboard :(

[@Catfishedge]

Thanks

[@brixelus]

When I deploy my 45 shaft it leaves about 3 inches of shaft on top. Is there anyway to trim it lower?

[@TheFishergal]

HI thanks for the great video Chad. I'm contemplating getting one for my 1991 Ranger bass boat. My bass boat mechanic thought I was getting an Ultrex I pilot and said he would get rid of the plug and just wire it directly. Is this a bad idea with the Ulterra?

[@Catfishedge]

If never wire one direct but that’s just me.

[@joseyanez214]

i recently had to change a battery and prior to that the motor deployed fine- after the battery install it won't deploy. The remote says batteries are fully charged but shows the prop with a line across it. Can u shed some light??

[@millelacsbound5190]

Great video. My gen 2 Ulterra is very noisy turning left or right. Is there some other place to grease as it was not that way when new. I use my motor a LOT.

[@Catfishedge]

Not that I know of

[@hopperdeb]

Why is my Ulterra randomly spinning around & tying itself in knots when it’s on spot lock?

[@chadhunt3789]

Where is the foot pedal or is it hand held only. Wireless?

[@cedricstone7306]

Great tips Chad, thanks...but still can't get computer to reboot passed stow or deploy or pause function....everything is on hold or is locked up.Lubed and tighten belt? But still no action No advice or service agent in NZ over xmas!

[@cedricstone7306]

Yeah, just had to add this as there is NO response from anyone, all the brains and service options are on holidays xmas/New year 4 two months both Aus/NZ . MK is dead and I've no way of overriding computer to get MK ulterra to function? Done a manual stow/deploy, then did computer managed deploy/stow only to have power head(thrustmotor) rotate 90 degrees and jam in housing base. Reset option from pause to deploy just convinces the computer to detect an overload....and locks up any other options (safety issue... I guess?) Have removed unit from bow and now 2x12 volt batteries to bench test. Can MK Ulterra unit be side-mounted on bench , hooked up to batteries for bench test?? No room low ceiling room or bench height to allow vertical deploy/stow option. There's no other way to release the stow tension....just asking someone?

[@kevinbriggs2611]

HELP!!!!! My last fishing trip, my Minn Kota Ulterra "paused" while deploying once it raised up to a vertical position. Mr. UnlikeU, I tried what you showed in this video and all I could get it to do was lower the shaft, not raise it and not allow me to stow. Unfortunately I have a tongue mounted step directly below the trolling motor while on the trailer. If I go down another 1/2", it will bottom out on the step. Any suggestions how I could get it to stow?????? THANK YOU!!!! Reply

[@105tuber]

My location sensor is flashing blue when I turn it on and the remote is not picking the motor up. It flashes blue for a little bit and turns off

[@MaxMeridius0920]

I have a Maxxum 74 , 24v that has a 4 pin power connection - I’m replacing the motor with a 24v Ulterra - it has the 3 pin male plug - can I just swap it for the 4 pin? If you know that would be great! Thanks for the video! Awesome info!

[@muskietime]

Use the plug he recommended in the description for best results.

[@Raven09s]

Minn Kota recommends a water based silicone spray for lubrication. On their company website video, they use pledge.

[@liquidleblanc1920]

I have seen that exact video a few days ago, he also mentioned to “ not “ lube the motor trim gear behind the side plate. But this video and Gentleman has convinced me of his way, being he has had it for 3+ years and 0 issues and seems to be very confident and well the proof to me is in the pudding haha but I’m sure as we all stumbled across these types of videos as we are trying to protect our rather large investment in these things, we are better then most already to do the preventative things.

[@Catfishedge]

Pledge causes problems

[@gregspears7]

Thanks for the tips. While using my Ulterra ,a puff of black smoke came out of the housing resulting in loss of power. When the housing was removed , there was no burned wiring or blackened areas. The fuses on the battery were good but it will still not power up. Any suggestions would be much appreciated.

[@eldonpulfer3515]

you probably fried the capacitors on the control board. that's what happened to my terrova. Steering unit went bad. Apparently if the steering motor draws too much current it will fry the control board. You'd think they would add a fuse or other protection scheme to protect the control board. DUH!!!

[@jasonriesmeyer2409]

What what the plug you used , brand ect? Waited till the end of video and you never said,lol. Great vid...!!

[@Catfishedge]

amzn.to/3p3TRSV

[@mcooper320]

I also love my Ulterra. Mine is an early version and the spot lock is not as good as the later versions, my understanding. Like yours, mine has been trouble free for 5 years.

[@Catfishedge]

Yes the original spot lock is 15 foot range and the newer is 5

[@bassplugger1]

@@Catfishedge I just purchased a 2012 boat with the ulterra . The boat has been sitting in a closed garage and only has 3 hours of use. What year are you referring to as an original spot lock with a 15 foot range?

[@davidousdigian4690]

Thanks for video. I have used my motor for 2 years without issue. It will not deploy. Power comes and stays on motor and pedal. When hitting deploy on pedal will not deploy then beeps. Tried power off and on holding power button in goes to green when pressing power 3 times does blink red. Took both sides off no wire pinching. Any suggestions for fixing?

[@Catfishedge]

Contact your MK service center and get them to look at it.

[@Dmnazdaq]

Very good information. My new Ulterra was making a clicking noise when lowering and was thinking it was in need of lubrication. Do you loosen the rubber belt before spraying silicone on underneath side? Can you use regular WD40 or does it have to be 100% silicone WD40? Learning my Helix iPilot Link so will look for your KZbin on that, too. Subscribed & “liked”. Thanks

[@Catfishedge]

No just spray it on there

[@Dmnazdaq]

Thanks. Found the 100% WD40 spray and need to get marine grade lubricant. Any particular marine brand lube that you use?

[@peterbaillon7615]

I get the motor error message every time after stowing. I have to shut off the motor and remote, and turn on again then I can redeploy. I assume doing the lubricating as you have suggested will fix this? I will have to wait until spring to try it. Also, I get a “motor paused” message on the remote sometimes when I turn the motor and remote back on. What is this and how can the motor paused issue be resolved without having to turn the motor and remote back off/on yet again? Thanks. Your video does appear to be very informative and I look forward to following your advice next spring when I can launch the boat agin.

[@Catfishedge]

Maintenance should fix it

[@TheDarienJim]

I have had to reset my a few times following the reset code procedure (3 push of the buttons within the first two seconds of starting up) and this has always worked. But this weekend it did not. Is there any other reset or diagnosis codes I can get to diagnosis what the problem is?

[@Catfishedge]

Unplug it, plug it back in and reset

[@esoxinator968]

I have the 1st gen ulterra and always maintain the only issue ive had is gopro remote screws up the opperation of it I guess wifi crosses idk

[@Catfishedge]

Yes, sometimes bluetooth has crosstalk. I've not had issues with the TM but have with other BT devices.

[@fishin-impossible2992]

Good info brother. I don't own an ulterra but everything out there needs some preventive maintenance. I check my minn kota and hit it here and there with some silicon spray once a month.

[@Catfishedge]

I'll try. This is my busy time of the year so I can't hardly keep up with my own stuff right now.

[@fishin-impossible2992]

@@Catfishedge I'm sorry brother I shouldn't have asked. Don't worry about it

[@Catfishedge]

It’s all good. Just a tough time of year for me trying to keep up with things but if I get a chance I’ll look.

[@allencogar8658]

Just purchased Ulterra. Older demo model from a few years ago, but unit is new. Not sure of the date/year. I am a stickler in regards to electrical connections and terminals. I am not an electrician, but I would like to know what you would use as a high grade male/female plug. Also what size breaker. I have the Ulterra 80lb - 54" - 24 Volt, and purchasing new batteries to go with it. Thank you!

[@Catfishedge]

It's in the comments here several places

[@3taylo3]

Hey Chad, My ulterra wants to droop when it comes back in to stow and even got caught on the storage lip once and gave me the motor error. Does tightening the belt tighten the entire prop unit? It seems to slip when it pulls up (because of weight).

[@Catfishedge]

Start with tightening the track

[@river_rats5625]

Why can’t I turn the prop speed up using the remote? The remote beeps at me. The foot pedal is able to control speed..

[@Cdawg1871980]

Is it messy spraying the track ? I’ve had my motor 3 years and haven’t done any of these but I am going to start ASAP

[@Catfishedge]

No

[@drxnupe]

what are your thoughts on quick release brackets? some folks say that they're a safety feature.

[@Catfishedge]

No go!

[@gilb5710]

Catfish Edge Why not?

[@knarf417]

Any reason to support the head end of these or is it a waste of money? My bow rail runs underneath it so it would be easy to do, but if it’s unnecessary....... Thanks!

[@glenndaugherity6187]

Some guys do if they fish big water a lot in rough conditions. We don’t for ours and haven’t had any problems and we fish Lake Erie and Green Bay but not everyday like some people. If you don’t drive crazy in rough conditions you’ll be fine without it.

[@ryanpearson2481]

👍

[@josephearnest5443]

I am having issues with when it stows it will operate and place itself in position but remote still shows stow option but it will not go any further and will not deploy either

[@Catfishedge]

Reset it

[@michiganfishingnationtv]

What kind of plug specifically do I need for my 24V 80lb Ulterra?

[@Catfishedge]

Make sure it's the correct amp rating. That's the key!

[@paulrowe4502]

@@Catfishedge Why would they have the wrong plug? Isn't the plug that comes with it correct?

[@edwardm.9150]

Hi Michigan Fish.......he is showing the MARINCO-70A Trolling Motor Plug and Receptacle in the video. Its the BEST!

[@bassplugger1]

I just bought a 2012 ranger with 3 hours on it. The original owner only used it one time and died after having the trolling motor installed sometime after 2017. His widow sold it without knowing where any of the manuals were, and also the remote for the motor is missing. It came with the 2017 ulterra i pilot link with universal sonar, (no side or down imaging). Also a helix 9 chirp SI GPS G2N at the console with the transducer at the stern. Also a helix 10 sonar GPS ( no "N") at the bow connected to the ulterra transducer. The two units are connected with an ether cable but the i pilot link 8 pin cable is not attached. It is laying under the cover plate at the bow coiled up with a zip tie. Can you explain what I need to do to get where both units can deploy and stow the ulterra and hopefully use the other features that it is designed to do? I hope you can explain it to where a 65 year old country feller that's not too savvy with technology can get it working. thanks

[@Catfishedge]

That’s way more than I can walk through in a YT comment

[@bassplugger1]

Thanks I think I have got it figured out

[@michaelcass5319]

Help lol. The trolling motor is stopped at an angle do to me hitting the pause button to clear weeds off of it. The red and green lights are alternating off and on. The power button does nothing I cannot shut it off. Any ideas? Thanks, Mike

[@Catfishedge]

Unplug it and plug it back in then perform the reset

[@jeffdurocher8669]

I've got that hat :)

[@ronscott2343]

Great info. However, my brand new Ulterra spot lock fails randomly and I have to press the anchor button again. My neighbor just bought a new one for his new boat and his also stops spinning and the spot lock button has to be pressed agaon. Surely we can't be the only ones with this issue. Batteries are charged fully and on trickle charge for days...

[@Catfishedge]

Check the voltage

[@ralphzobjeck5786]

@@Catfishedge Also make sure you calibrate the unit. Many people don't realize this NEEDS to be done.

[@Outdoorguy_FrankPearson]

I notice your motor is 180 degrees from mine when stowed. How do I change that?

[@Catfishedge]

Positioning reset procedure is in the manual. I like the prop in towards the boat. I break less props that way.

[@coho33]

My Altera freezes up and won’t turn left or right after deployment any suggestions.

[@Catfishedge]

Seems like it has something to do with the remote syncing when that happens.

[@christopheradams857]

I'm thinking about buying the Ulterra trolling motor. Do you know the distance when deploying and parking the truck? Thanks Chris

[@Catfishedge]

Not sure what you’re asking

[@macentofanti4100]

@@Catfishedge How far away can you be with the hand held remote and still have it function the trolling motor while the boat is sitting in the lake after launching

[@thecatfishking9047]

I tried to get a 2019 SeaArk ProCat 240 with a Minn Kota the other week the banks said no :(.

[@Catfishedge]

Sorry

[@Catfishedge]

Sorry

[@thecatfishking9047]

@@Catfishedge Hopefully get it next year, in the meantime my little 14 foot V bottom aluminum boat will do.

[@gilb5710]

Try a different bank or Credit Union! Fulfill your dream!

[@randallwebb226]

My ulterra won’t pull in after it comes out of water and is laying horizontal and I’ve reset it couple times where it goes all the way up and down. Not sure where to look next

[@Catfishedge]

Tighten the track and reset the orientation.

[@marquismottley6867]

My MK ulterra will turn left and right but prop won’t spin any ideas on why?

[@Catfishedge]

Pull the prop and check it

[@eddieensor6208]

What is the correct plug please and thanks?

[@Catfishedge]

amzn.to/3p3TRSV

[@hopperdeb]

Mine is choking up on Spot Lock, twisting 360 degrees. What can I do to stop that? Ruining my fishing

[@Catfishedge]

Fish when there’s wind

[@bigbird2424]

Mine squeaks when it’s in spot lock and when it turns

[@johnnyfive8748]

Mine is squealing quite a bit when trimming up and down even after spraying silicone spray. It’s been doing it for a while, I’m just afraid it’s going to crap out on me.

[@JCASTELLUCCIOJR]

Did you spray with SILICONE spray: the drive belt, SHAFT AND ROLLERS ON TOP/BOTTOM OF BELT??? Was told NEVER USE spray with petroleum dispersants (WD-40)!!!!

[@johnnyfive8748]

@@JCASTELLUCCIOJR I have been using silicone spray after every few uses and it has helped.