CD009 VQ35 Tranny to VQ37VHR Engine Preliminary Homework

  Рет қаралды 1,423

supakat500

supakat500

Күн бұрын

Пікірлер: 18
@93lethanh
@93lethanh 3 жыл бұрын
Thanks for making this video. I have the same combo. Thought I might be able to bolt it together. Not as motivated or skilled enough to follow you though.
@supakat500
@supakat500 3 жыл бұрын
Yea it wasn't too bad, just time consuming...in the log run, it ended up saving me lots of dollars. I even have a spare tranny I picked up from an 05 g35 from the junkyard for $180. If the current one goes, then swap bellhousings and keep on going!
@93lethanh
@93lethanh 3 жыл бұрын
@@supakat500 I think I'm just going to try and pull a 35hr with tranny if possible so my parts will be somewhat compatible. Haha. Did you have any issues with the steering? Was thinking of spacing the engine up and subframe down to get the clearance instead.
@supakat500
@supakat500 3 жыл бұрын
@@93lethanh The only problem with HR tranny is the internal slave and a kit to make external is $700 last I checked. This is where I saved my money! As for steering, common fix is to rotate steering rack to clear started. Tons have done this who drift and should not be an issue. Also, there is a trick to rewire the alternator too to work with old system. If you are swapping harness, then you should be ok. Just food for thought.
@93lethanh
@93lethanh 3 жыл бұрын
@@supakat500 thanks for the tips! Your vids have been mad helpful. Hopefully I'll get my s13 to stop being in a perpetual wheelie too. 😂
@supakat500
@supakat500 3 жыл бұрын
@@93lethanh no doubt...glad it can be helpful...I actually finished fuel and bolted down the intake but took a vacay to Greece with the wife...heading back to the states today...hopefully get some work done this weekend.
@SidewayZ.garage
@SidewayZ.garage Жыл бұрын
3 years later… did you find a solution and does the input shaft line up?
@djbrueal
@djbrueal 9 ай бұрын
Also curious
@BEAZYBUILTIT
@BEAZYBUILTIT Жыл бұрын
Dude you ramble a lot 💀
@JasonCabrera
@JasonCabrera 4 жыл бұрын
I’m building a ka24det stock on a megasquirt v3
@supakat500
@supakat500 4 жыл бұрын
Sweet...make 350whp reliably. Good luck man...fun times ahead.
@1slowtj
@1slowtj 4 жыл бұрын
What is that whole on the side for crank sensor ??
@supakat500
@supakat500 4 жыл бұрын
Yes, crank sensor.
@grahamh6444
@grahamh6444 4 жыл бұрын
@Supakat500 did you see my email about my tune on ka24det? Hope keeping well
@supakat500
@supakat500 4 жыл бұрын
I apologize for the late response. I thought I had responded. Tune sent. Again, my apologies.
@grahamh6444
@grahamh6444 4 жыл бұрын
@@supakat500 top man
@JasonCabrera
@JasonCabrera 4 жыл бұрын
I miss the ka24det
@supakat500
@supakat500 4 жыл бұрын
I do sometimes but the TQ and sound of VQ make it all worth it...now 11:1 compression out of a 3.7 is gonna be nasty!
VQ37VHR SWAP COST BREAKDOWN
13:30
Sleepless Performance
Рет қаралды 16 М.
It works #beatbox #tiktok
00:34
BeatboxJCOP
Рет қаралды 41 МЛН
Cheerleader Transformation That Left Everyone Speechless! #shorts
00:27
Fabiosa Best Lifehacks
Рет қаралды 16 МЛН
Cat mode and a glass of water #family #humor #fun
00:22
Kotiki_Z
Рет қаралды 42 МЛН
REAL or FAKE? #beatbox #tiktok
01:03
BeatboxJCOP
Рет қаралды 18 МЛН
AWD AND VQ37-swapped Off-Road 350z
18:05
Larry Chen
Рет қаралды 27 М.
KEY INFO YOU NEED BEFORE ENGINE SWAPPING YOUR VQ
12:25
DripMyWhip
Рет қаралды 11 М.
Stroker Kits Explained
18:12
Red Beard's Garage
Рет қаралды 26 М.
MicroSquirt KA24DE 1st Start
4:54
supakat500
Рет қаралды 5 М.
MIND BOGGLING ENGINE GEOMETRY - Rod Ratio Explained
18:43
driving 4 answers
Рет қаралды 6 МЛН
VQ37VHR Swapping my 350z | SouthBend Clutch Install | Episode 2
15:21
Sleepless Performance
Рет қаралды 3 М.
5 golden porting rules - #1
17:17
David Vizard
Рет қаралды 244 М.
Blown Up - Is It Worth Rebuilding? Engine Tear Down and Analysis
1:00:33
Vice Grip Garage
Рет қаралды 2,4 МЛН
1973 Datsun 240z VQ37 swap
4:52
Neighborhood mechanic
Рет қаралды 1,8 М.
It works #beatbox #tiktok
00:34
BeatboxJCOP
Рет қаралды 41 МЛН