CEN Racing M-Sport Ford Puma Rally 1 UPGRADE & REPAIR

[@VERY_VARIOUS_VIDEOS]

Thank you very much for sharing. Beautiful video 👍

[@MauzyrockRC]

Hey thanks! My pleasure!

[@VERY_VARIOUS_VIDEOS]

@@MauzyrockRC You're welcome friend 🙂

[@sumerland78]

I installed the steering assembly upgrade today. After assembling the three pieces at 4:10 there is more play than with the original plastic part. I wish the holes in the rod connecting the bellcranks were a tiny bit tighter.

[@MauzyrockRC]

Oh! I did not notice any more or less slop on mine. That is too bad though. Can you make a lexan shim or something to take up the slack?

[@sumerland78]

@@MauzyrockRC Good idea! I noticed the play is less once everything is fully installed. Will check how it drives and add a shim if required. The servo mount upgrade is next.

[@MauzyrockRC]

@@sumerland78 Cool. I have only had a chance to run mine 2 times since winter started. I think the servo may be a weak point. So maybe that will get swapped then I'll see about other upgrades too :)

[@DustyFingersRC]

Best start to a video ever 😂 You crack me up. Keep up the good work 👍🏻

[@MauzyrockRC]

Haah! Awesome. Mission achieved! Thank you!!

[@RcNickster709]

Yup. Looks good!!! Always a good upgrade. Probably adds a little weight maybe? Mental Note. When using your grinding wheels. They get worn down to the smaller diameters. Most people throw them away. I keep them just for this purpose. Smaller diameter wheel = less damage to the frame. Just thought I would mention it. :) Excellent video once again

[@MauzyrockRC]

Awesome to hear. It was pretty light bit of kit, maybe a gram or two heavier. I thought there may have been bearings included... alas nope. Oh yeah, I never thought about keeping the worn down cut off wheels, the one I used was pretty worn, and yeah I think I made much smaller a gash in the chassis than a full sized one. Good tip! Thanks so much!

[@AddamsPlayground]

Nice looking and tough upgrade for it! Should not have any more issues with that in there!

[@MauzyrockRC]

Oh she’s a beauty! 7075 should hold up as longs as I dont smash all the parts around it 🤣😂🤣 Cheers!

[@RallyandTrail]

Possibly broke due because CEN not using a servo saver …nice upgrade though 😎🏁

[@MauzyrockRC]

Yup. Agreed, however a beefier assembly is always better :)

[@rexrcs]

Good upgrade, needed on bigger scale

[@MauzyrockRC]

Ya, hated to do it, but it was necessary...

[@rchelistef506]

Belle job tu parle bien l'anglais moi pas dutout

[@MauzyrockRC]

Ah merci. Je suis un rare Terre-Neuvien Bilingue ;)

[@RCSomething]

Mauzy ! Man, this stripped screw is the worst but you did fine with that sh... ahaah take care and awesome vid. Have fun with that car ( when the weather allows you to :D )

[@MauzyrockRC]

Hey thanks! Maybe some Ice rally?? -20 celcius is too cold for RC for me lol! Merci!

[@TidyRC]

Wot other upgrades are there for this that u know of? I’d love some off road tyres if u know any that would fit.

[@MauzyrockRC]

What I know of so far is hobbydetailsretails.myshopify.com/collections/cen-racing-1-8-rc-car-upgrades-parts As for tyres, I am going to try the ones from my HPI WR8. I think the HExs are the same.

[@TidyRC]

Take my strong hand…… 😂

[@MauzyrockRC]

🤘😂🤘

[@SamSung-mz5it]

Your tool was stripped not the screw you can clearly see also an MiP tool would of removed it no problem and you used a ball end hex which is only used for tight angles.

[@MauzyrockRC]

Hey, so I did use my MIP driver, and another hex driver and then the ball hex. the screw was totally stripped. Thanks for the input though.

[@ijinxit8541]

Can you drop a link to the part ? I need it

[@MauzyrockRC]

I found them on this site www.hobbydetails.com/