Change a 3rz engine oil pump # toyota

In this video we explain the easiest way to change the oil pump for Toyota engines
#engine3RZ
#pump
#hilux
#3RZ
#pump3RZ
Changing the oil pump of a Toyota 3RZ engine requires a bit of mechanical knowledge and experience. Here are the general steps to change the oil pump of a Toyota 3RZ engine:
1. Drain the oil: Before beginning work on the oil pump, you should drain the oil from the engine to prevent oil spills. Locate the oil drain plug under the engine and use an oil pan to catch the oil.
2. Remove the oil pan: Remove the bolts that secure the oil pan to the engine block, then carefully remove the oil pan. Be careful not to damage the gasket that seals the oil pan to the engine block.
3. Remove the oil pickup: Locate the oil pickup tube that is attached to the oil pump and remove it from the engine block.
4. Remove the oil pump: Remove the bolts that secure the oil pump to the engine block, then carefully remove the oil pump. Be careful not to damage the oil pump drive gear that connects the oil pump to the engine.
5. Install the new oil pump: Install the new oil pump onto the engine block and secure it with the bolts you removed earlier. Make sure the oil pump drive gear is properly aligned and engaged with the engine's gear.
6. Reinstall the oil pickup: Reinstall the oil pickup tube onto the new oil pump and secure it to the engine block.
7. Reinstall the oil pan: Clean the gasket surfaces of both the engine block and the oil pan, then reinstall the oil pan and secure it with the bolts you removed earlier.
8. Refill the engine with oil: Refill the engine with the recommended amount of oil and start the engine to check for leaks.
It's important to note that the above steps are general guidelines, and the specific steps for changing the oil pump of a Toyota 3RZ engine may vary depending on the exact model and year of the vehicle. Always consult the vehicle's owner's manual or a qualified mechanic for specific instructions and recommendations.

[@jacobomatheumarroquin4340]

Buenas tardes Maestro pregunta la tapa de la bomba de aceite porque no se le pone empaque en donde están los tornillos ( BELEMOIDE ). Saludos desde Guatemala 👍

[@obaid.371]

Good.

[@timcarter9146]

Couldn't have cleaned the dirt around it first I know that's all inside your motor

[@juancardoza4515]

Disculpe que Toyota es por q tengo una tundra de me dijeron q se necesita cambiar la pompa de aceite

[@LxTxSURGE]

Tacoma

[@bodyzoasispersonaltraining9186]

Wow. I thought this was stuck in a mud hill.

[@jheancarlos1979]

Y como hago para que agarre seba y bombee aceite

[@7asn]

The new pump

[@user-wh2rl6ec3z]

No tiene lado porque trae Uno's puntos como iria

[@elisabethtimaran7274]

Tengo una toyota hilux 2rz se le cambio la bomba de aceite y no lubrica q puede estar sucediendo

[@cristiandubantorresmalaver7370]

Tengo el mismo problema, ya lo solucionaste?

[@jheancarlos1979]

@@cristiandubantorresmalaver7370 hola como solucionastw la lubricasion de la bomba la mia es toda nueva y se limpio el carter y ahora no sube aceite si me piedes orientar gracias

[@urielgarcia4204]

Yo estoy igual

[@oscargomez2588]

tengo el mismo problema cambie liga y reten y ya no tengo lubricación

[@jhonfernando3258]

Solucionaste?

[@jheancarlos1979]

@@jhonfernando3258 hola como solucionaste la lubricacion en mi caso todo es nuevo y origiinal y se limpio el senidor pero no sube el aceite sera que me falto algo si puedes orientarme

[@aldogarcia236]

@@jheancarlos1979hola solucionaste?? Tengo el mismo problema

[@davidbuenrostro8205]

CAN YOU UPLOAD ONE OF HOW YOU REMOVED THE PULLEY IN FRONT OF THE PUMP PLEASE

[@7asn]

soon

[@CheletoVlog]

It slides out, no pulley removal tool required. After bolt removal

[@lemonsaregoodrightl2854]

You need a puller most of the time

[@LeoGon-xo7ip]

Deviste dejar el video hasta el final.

[@7asn]

Ok

[@ZZROBProductions]

All my screws are stripped

[@HappyPel]

You have to use an exact bit or they strip. I had one strip and a drill worked.

[@nestorcordero2358]

Where can you get those screws at May need a couple, helpful video thanks .

[@HappyPel]

@@nestorcordero2358 I think they are M6 x 1.0 x 12 flat head. found some stainless hex head ones on eBay for $8

[@nestorcordero2358]

@@HappyPel thanks buddy appreciate your help .