Change Nozzle FLSUN V400 How To Hot end Fast Delta 3d Printer

[@flamingrebel69]

Perfect! My nozzle literally just came in today and you're about the only one who ive found who has a video really showing how to change the nozzle. Easy and straight to the point. Much appreciated! Followed.

[@carphotography]

awesome, someone just mentioned dont put the rubber sock back on until after you printed the calibration cube so you can check for leaks. thanks for watching.

[@CheeseFriesAndCoffee]

I'm so thankful you're making these videos. So far everytime I've wondered about an operation with the V400 you've had a timely video explaining just what to do.

[@carphotography]

Im thankful for you guys watching them :D soon i am getting the ADXL345 input shaper :D so were find out what that does when it turns up, i believe helps with the ringing. will be making a video on it, and anything else i can think of.

[@CheeseFriesAndCoffee]

@@carphotography Have you had to adjust belt tension yet?

[@carphotography]

@@CheeseFriesAndCoffee only the small adjustment i made in the maintenance video to make them the same tension other than that no they have stayed good :D

[@booboofinger2595]

Great! adding this to my v400 maintenance folder Thanks!

[@carphotography]

awesome :D thanks for watching :D hope it comes in handy :D

[@silentd.5806]

I appreciate all of the videos you put up !

[@leonardoperalta2932]

I appreciate your videos, you save lives!!!. Followed

[@Verton_D]

Hi. I want to install a .2mm nozzle. Is it doeable on the Flsun V400? I am ordering the Micro Swiss Brass Plated Wear Resistant Nozzle for CraftBot Flow Generation hotend (.2mm). Also, does the length of the nozzle matter? there are some with shorter threads. please let me know. thanks.

[@xXDerFranzXx]

Where do you buy the silicone Socket for v400? i dont find anything in the web

[@marcroix1]

gran explicación, gracias por compartir

[@bettydaltonnewbold2019]

Looking for a replacement nozzle for my V400. Almost impossible to find in the US. Any suggestions? Thanks.

[@carphotography]

a lot of people reccoment this one www.bondtech.se/product/bondtech-cht-bimetal-vol-coated-nozzle/?fbclid=IwAR0Zw9Lrhflqxl5SYttQM3ng-PCmBKxl6ylVkrad98eBeY2tWeULeHOJekc

[@sinantel921]

teşekkürler...thanks

[@gehrkea]

Just what I needed right now, about to switch to CHT thanks! No need to redo bed mesh or anything?

[@carphotography]

i dont think bed mesh is needed as long as the z height is correct it should follow the previous mesh, i am doing a large print today so i mention if i have ant issues. thank you

[@gehrkea]

@@carphotography thank you let us know how it goes!

[@googleaccount8578]

Also did you isolate the thermistor wires with kapton ?

[@carphotography]

no i didnt what you see is what i did, maybe if i switch it again i will look into that. thanks

[@theelevatedone8043]

I recently got mine and it had some rubbery white material around the nozzle, is that normal?

[@carphotography]

yes that is normal is is silicon i believe

[@MartinDev77]

Hi, you know where can buy replace nozzle for the v400?

[@carphotography]

this is where i got mine, store.micro-swiss.com/products/e3d-volcano-compatible-plated-wear-resistant-nozzle-1-75mm-filament other a lot if you liik in the details should mention the printer it fits. good luck.

[@charlesrestivo870]

Can you save to pad or do u have to use computer screen

[@carphotography]

in the console on the pad you can type SAVE_CONFIG and it will do the same.

[@charlesrestivo870]

@@carphotography thank you very much for reply Trying to understand why the extra layer of complexity is needed ( computer)

[@carphotography]

@@charlesrestivo870 i just use it because it is easier to type on than the speeder pad :D and i do really like the wireless function as i use a computer in another building also for sending the designs and i can heat it up before i get out there so its ready to go :D

[@charlesrestivo870]

@@carphotography I like using sd card wifi is never stable thank you again for infromation