Changing injectors on Cat skid loader

[@proberts34]

Pretty snazzy torque wrench, with the "approaching" indicator lights and the green "you're there" indicator lights. 👍

[@edstevens9357]

Gave you a sub from diesel creek. You have some great content can’t wait to watch more

[@Military-Museum-LP]

New subscriber on board. Matt from diesel creek sent me 😊!

[@FQP-7024]

i yearn for the day a company rises from the ashed and makes actually long lasting, modular easy to work on equipment, they will rise so damn fast.

[@RuggedArtistry]

I too am here as a result of Matt's recommendation. That is one beautiful Louisville that you used to haul Matt's new Cat dozer. How is it that you can drive a truck and trailer of that size without any DOT numbers or identification? Just curious.

[@ScrappyIndustries]

Thanks! I’m not for hire I was just helping Matt out

[@488Magnum]

Had to check out your channel after seeing your Penn State Pullers hoodie on Diesel Creek and was like I know Sam. We had classes together in AG Engineering.

[@ScrappyIndustries]

Boots how have you been!

[@488Magnum]

@@ScrappyIndustries Doing well! Fixin Dodges and testing Deere's.

[@CMDSR]

Good ole Tokai Denso parts made to last until you get them installed.

[@TruckerChick]

Popping over from Matt's Diesel Creek to check out your channel. Subbed and liked. Looks like nice content.💪

[@ScrappyIndustries]

Thanks for stopping by!

[@TurboWindsor]

What were your symptoms just slight misfire? Any smoking? I have a 289D and as it’s warming up sometimes I notice a little stumble but at times when under higher throttle fully hot, it will smoke faint white hot smelling for a few minutes then clear. No loss of any coolant or oil, so I’m thinking an injector is starting to freak out.

[@ScrappyIndustries]

It was mainly just an intermittent misfire- especially when cold. I was afraid of hurting the DPF as you have to remove the engine to replace it on these....

[@deeper4cheaper128]

Just my two cents.. maybe just set the camera somewhere so you don’t have to hold it and Timelapse / speed up the part of the job that you can’t hold the camera vs. just cutting it out, would be cool to see more of the repair.

[@ss-qw8vm]

I love your show. Hi Sam I saw you on Diesel Creek helping him out. thank you Sam I am

[@ScrappyIndustries]

Awesome! Thank you!

[@DieselCreek]

Didnt even move any dirt after 🤷🏼‍♂🤷🏼‍♂

[@rossh1152]

Did you have any diesel dilution in your oil ? I have the same machine 1600 hours and my lab result said I had a lot of diesel in my oil. Engine runs well though

[@45chromeshop]

same problem here, 289d getting lots of fuel in the oil, smokes a little blue smoke

[@brendananderson2787]

How did you find out which injector was bad. Planning on doing mine this weekend. Depending doing all 4 aftermarket or just buy the one from cat dealer

[@deeper4cheaper128]

She needs a weight loss program! Where did you get the manual for $40?

[@rossh1152]

How did you diagnose your problems to be sure that it was an injector issue ?

[@bdogsss8356]

How were you able to get your hands on the cat et software? I have a lot of machines and calling cat to diagnose is too expensive

[@ScrappyIndustries]

You can pay for it from cat-I’m not sure what the cost is. I borrowed it from a friend who is a lot more of a mechanic than I

[@HungNguyen91622]

Where you located? I may help you if you are near.

[@jameschastine4990]

Have been able to find parts to fix your combine?

[@ScrappyIndustries]

Yes they put the axle back together and got it inside. Working on replacing the subframe under the radiator now

[@R3d_D3ad369]

what tool do you need to load the trim codes onto the machine? where can i get one ?

[@chrisholzer1681]

Thank you for this video. I’m working on a kubota ssv 75 and I am frustrated with the way they put every cooler possible above the engine, and then put a leaky hydraulic fan in between. If anyone has done this on one of these, I’d love some wisdom on wether I really have to work out of this 5 inch space or if I should just pull the whole cooling module.

[@ScrappyIndustries]

Hmm yeah I can’t really offer any great advice there sorry. You don’t need a ton of room over the engine but you definitely need some. I’d probably start pulling coolers

[@chrisholzer1681]

@@ScrappyIndustries I ended up pulling just the shroud so I could gain access, wasn’t a bad job! Thanks again for the video

[@73DiamondReo]

@ 1:43 watch me spin this bolt. needs to be made Tier O

[@ScrappyIndustries]

Can’t hold a camera and a wrench so it’s a demo 😂

[@rkdob]

from diesel creek

[@ScottWM54]

That's what you call a knuckle buster....

[@archangel729]

What would be nice if they had these motors on a rail you can slide it out and work on it slide it in ,and go to work with minimal effort.

[@archangel729]

Send the injectors to area diesel they have a youtube channel

[@glenscheible9467]

If a Kubota Engine go to Kubota for parts. Be cheaper than Cat.

[@deeper4cheaper128]

Yeah it’s a catbota