Cheap! flow through exhaust Yamaha RIVA RACING KILLER

83mm 90 degree pipe www.ebay.com/it...
89mm 45 degree pipe www.ebay.com/it...
Please keep in mind companies change their sizing all the time.
My filming gear
My drone amzn.to/2nApOHu
My gopro amzn.to/2oUq8RT
My camera amzn.to/2nAjmAp
My camera amzn.to/2oUpyDy
My computer amzn.to/2oUzGfw

[@elbatobeach]

2016 VXR from water box is 3" 1/2 to 3 1/2" 90 degree to 3 1/2" 45 degree pipe. Thanks for great video.

[@AlexanderTheGrateful]

Just a heads up, some guy on the forum have mentioned that the extra weight and the position of these home made money saving exhausts puts strain and pressure on the stock exhaust exit and starts cracking causing leaks

[@FLORIDALIFECLIPS]

Cool!

[@racerx2084]

Well I ordered the pipe and that fit fine into the rubber part that goes to the rear exit but the silicone part is a no go so far. 1st company I ordered the 3.25 n it was way to small. Measured at 3’” on the inside. Then I ordered another that specifically said 3.25” ID. Not going on still. 1/4” is pretty hard to stretch. Should have gone with my gut and ordered 3 1/2” for everything. The metal pieces have the bead roll so even if it wasn’t super tight it would clamp down ok

[@emmanuelhernande1014]

Hello can you update the links for ebay I would like to do this to my 08 fx cruiser

[@FLORIDALIFECLIPS]

Ya check tomorrow

[@johnh9507]

thank you for mentioning the od and id of the pipes you bought

[@franciscoreyes3827]

The link to get the pipe and rubber isn’t available. Can you share with me please

[@edgeprep]

I’ll check again but I didn’t see or unplug anything. Thanks for the quick response

[@FLORIDALIFECLIPS]

It should run without a problem all your doing is removing a couple of pipes and baffles doesn't make sense why it would not run correctly

[@sokmarley8330]

Why not tighten the clamps?.i did this exact setup last summer and ride the heck out of it ..really curious why not tighten them? Thanks.nice video btw

[@ThirdStrikeGaming]

So I’m assuming this works with almost any jet ski?

[@FLORIDALIFECLIPS]

No only on older Yamaha

[@ThirdStrikeGaming]

Well not exactly the fittings size but the concept should work for a Seadoo Spark

[@edgeprep]

So I tried this exact setup... tried to start the ski and I wouldn’t stay running. After much trouble shooting I never could identify any problems. So I ended up putting everything back to stock, and the ski ran perfectly again. Any ideas or did I miss something? Thanks for any help (2005 VX1100)

[@FLORIDALIFECLIPS]

I'm not sure I didn't have any problems maybe you have a sensor on your water Box or somewhere

[@mekuranda]

I was thinking of doing my 2013 VX1100.......did you ever work out what the issue was?

[@edgeprep]

@@mekuranda no I sure didn’t. I’m very mechanical having worked on my own cars and motorcycles all my life. I tried everything I knew to do and researched the internet as well for any similar issues or discussions with this conversion but to no avail. Each time I put the stock exhaust back on it ran perfectly. Weirdest part of it all is I actually removed the spark arrester and air filter/breather both before and after trying this exhaust mod, but the intake mod had zero affects whether the exhaust was stock or modded.🤷🏼‍♂️. Ended up selling both my skis this past Summer. Still have the boot and elbow; be more than happy to send em to you for shipping cost. They’re no good to me

[@mekuranda]

@@edgeprep thank you for the reply. I am in Australia ...not sure if international shipping is viable unless you have a fantastic deal with freight company. I have seen a few vids on people removing the air ribbon filter...not sure why Yamaha put it there, must be there for a reason... safety, flame arrestor...not sure I would want to reduce safety for a little performance gain, but the exhaust is unlikely to reduce safety and might sound a little better, beefier, and have a performance boost, at the expense of quietness...the VX is super quiet in stock trim.

[@edgeprep]

@@mekuranda ah! Yeah, probably wouldn’t make it to you without its own VaX passport anyways.🤷🏼‍♂️. Yeah I regretted removing the ribbon on the intake side after watching a few hull explosion. Definitely had a deeper more throaty tone, but wasn’t worth the risk. Everyone I knew had done that mod with no disaster, but there’s always that one chance. Nonetheless, good luck with everything on your ski. Also, wishing you all the best down there with everything you’re going through; it’s truly been unbelievable from my viewpoint. Sky News Australia is my regular go to for the past year because you can’t trust any of them here in the states. Anyways, stay strong…the world is watching us both! Cheers

[@annielaguila6319]

You have link for the parts you used??

[@dproulx7380]

I spent 57 on parts and getting pipe powder coated for 25 and I may need one more hose clamp!!! Great info ty

[@edemkounou7734]

What is the length of the aluminium pipe pls

[@ebazardlast1745]

Oh yeah you really can't beat that price, i like it ... thanks for sharing this though, and nice sky...

[@deetani6773]

Going to try this. Thanks 4 vid.

[@luisalfonzo2836]

Will this work for a 2019 VXR? Thanks for the video your the man 🤘🏼

[@FLORIDALIFECLIPS]

Not a 100% sure because I never did one on a 2019

[@brackineno]

crazy sound in midle rpm

[@FLORIDALIFECLIPS]

Neno Bracki That's a good thing people will know you're coming

[@deetani6773]

What about thru hull exhaust for cheap?

[@SlayerHawkX]

any problems with water backflow or anything?...other exhaust raise up higher..

[@FLORIDALIFECLIPS]

None

[@kkbodyshop]

Can you do this on a 2012 sho?

[@sxshethean3069]

How's everything performing after 3yrs from install?

[@FLORIDALIFECLIPS]

Great no issues

[@anthonygalloway7083]

I have a 2019 Yamaha EX and I have a free flow and I wanted to delete the water box. I was wondering if you could do this to delete the water box.

[@FLORIDALIFECLIPS]

Unfortunately cannot answer that question your best bet would be speak to a experienced mechanic

[@dannyg4267]

any videos of how this set up sounds??

[@FLORIDALIFECLIPS]

I did try making a video but after reviewing it the sound quality on video was not the same as in person I can tell you it sounds a 100% better than stock.

[@dustinabercrombie8939]

@@FLORIDALIFECLIPS is it too loud?

[@brettcynthia2403]

Is there any issue using Aluminumin pipe as opposed to stainless. I notice the stainless is close to the fibreglass body shell is there a min. Distance to stop heat transfer issues to fibre glass?

[@FLORIDALIFECLIPS]

I had no issue with it and i run it every weekend. also I am sure you can find some kind of thin stick on shield to stick on the hull from eBay.

[@brettcynthia2403]

FLORIDA LIFE CLIPS thanks great video by the way

[@kkbodyshop]

Is it loud?

[@SWFLJetSkiRiders]

What's this for?

[@randylovato7888]

OK so I have a 02 fx140 what do u recommend to use?

[@FLORIDALIFECLIPS]

Sorry can't help never did a 02

[@daltondrummer]

Used to have an FX140, I put a Riva free flow on it, and honestly, I was dissapionted on how quiet it was. However the Riva free flow is plastic so if you use metal i'm sure it would be louder.

[@randylovato7888]

daltondrummer was there any performance difference on it?

[@daltondrummer]

Honestly it felt slower, all these people think they get gains from making the engine more free flowing but it'll just run worse as its tuned for the stock exhaust. If you get it tuned to the new exhaust sure it would be faster. My old Fx-140 literally blew up right after I put the exhaust on. (No it wasn't the exhausts fault it was just old and leaking oil already. I did a lot of research and there's just so little mod support for the FX-140 that i'd recommend keeping it how it is. Maybe polish it and make it look nice to sell. I got a good deal on a FX SHO 2009 for 6K. MUCH faster, there's no comparison, it scared everyone who rides it with me. If you want to mod, get one with a supercharger and ECU tune it.

[@yoiwrx3883]

daltondrummer you is was slower do to the exhaust did it had an intake also or just exhaust?

[@05puzio]

what are the leg lengths of the 45 degree?

[@FLORIDALIFECLIPS]

Rick Puzio sorry out of town till Jan. I will let you know when I get back.

[@SlayerHawkX]

what about drone noise..?

[@dustinabercrombie8939]

I'm interested in noise as well

[@SlayerHawkX]

@@dustinabercrombie8939 i actually done this..was a bitch to get pipes on without and bad bend in them..but sounds good on ground..havent had chance to put in water yet..mine on a 2020 gp1800

[@salvadorestrada7097]

Hello what's the length size for ea pipe?

[@FLORIDALIFECLIPS]

I do not know the length it is whatever length they come in I did not cut anything.

[@salvadorestrada7097]

Sounds good thanks bud. I'm guna do this on my O7 waverunner FX HO. Hope 🙏 its a good mod

[@T3XANGINGER]

Would this work on a 08

[@FLORIDALIFECLIPS]

Yes

[@josephvolper3633]

Will this work on a 02 Yamaha fx140?

[@FLORIDALIFECLIPS]

If the exhaust setup is the same yes

[@josephvolper3633]

@@FLORIDALIFECLIPS thanks were can I find this stuff to order ?

[@josephvolper3633]

Do you know the length of the 45 degree pipe

[@timkerber6681]

If I write down the itemnumbers on ebay I cant even find anything? could you pls send me the link? So much appreciated

[@FLORIDALIFECLIPS]

links are up

[@timkerber6681]

so much thanks

[@FLORIDALIFECLIPS]

Tim Kerber please do keep this in mind that companies change their sizing all the time I do not know why but they do this is what I purchased and it worked

[@FLORIDALIFECLIPS]

Tim Kerber just please keep in mind again companies change their sizing I do not know why they change the sizing but they do

[@timkerber6681]

thanks anyway, you helped a lot ;)

[@kello236]

Hi where did you order these parts from?

[@FLORIDALIFECLIPS]

Ebay inter cooler turbo pipe

[@kello236]

What is the length of the 45°?

[@FLORIDALIFECLIPS]

@@kello236 I believe 12" not sure have not done this mod in a very long time

[@dproulx7380]

You should buy those parts in bulk and sell it for 150

[@murk339]

Will this set up work on a 2013 fx ho cruiser

[@FLORIDALIFECLIPS]

Can't tell you never done a 2013 I'm thinking it should work but you might wanna do some measurements.