God bless ya mister. Being a Backyard mechanic is tough especially in the backyard. Thanks.
@benzflynnАй бұрын
I agree. To eye it looks too narrow, the rails too low and no means of tilt or spin to compensate for unlevel ground or misalignment to the flywheel axis. You make me want to design something that could be fabricated locally. Thanks, WW.
@NoName-uz7sv Жыл бұрын
I appreciate you making this informative video! Lol i just got my transmission jack adapter today and was disappointed to find out it only had the one direction tilt🤦🤷
@blightstuff2629Ай бұрын
Your intro is dope
@Christopherbever19 күн бұрын
@@blightstuff2629 appreciated it as well
@vrm86gt Жыл бұрын
thanks for the review, I was gong to get one but I think i will pass and look for something a little better
@MrMehtabkhan7867 ай бұрын
Great video really enjoyed in the process of buying the adapter on a budget not on such a big gearbox so I’m hoping it will work thanks mk
@garymatthys3605 Жыл бұрын
I got the scissor stye from HF for $130 + tax. Got the job done, but the truth is, pulling an auto trans with the vehicle on jack stands is a miserable job.
@wrenchwranglers Жыл бұрын
Yes, for sure pulling a transmission without even a driveway is not fun :)
@oby-16078 ай бұрын
Since when is removing and replacing a heavy transmission a party. The tool worked.
@williamfrench9973 Жыл бұрын
Perhaps they show the jack perpendicular to the vehicle is that they were intending that for a transverse mounted drivetrain 🤷♂️
@wrenchwranglers Жыл бұрын
That is a good thought.... I didn’t put much thought into that as I try to avoid pulling transverse transmissions.... more parts to pull on average and more of a pain.
@williamfrench9973 Жыл бұрын
@@wrenchwranglers that is some truth right there my friend
@blackshirt4ever02 Жыл бұрын
Modify the tilt handle to accept a socket , so you can crank it under load.
@wrenchwranglers Жыл бұрын
That is a fantastic idea.... I need to implement that on future revisions.
@benzflynnАй бұрын
But is it robust enough anyway ? I can see that threaded rod busting under the strain of a breaker bar.
@williamdon34422 жыл бұрын
Cut it square from the bottom and use a washer welded from bottom. I’m in the same ordeal.
@wrenchwranglers2 жыл бұрын
That is a great idea, probably faster method than what we ended up doing.
@shehzadatif16 ай бұрын
These jack adapters are only good for small transmission in sedans like Civics, Corollas and Accords.
@94silverado442 жыл бұрын
It gets the job done for $60
@benzflynnАй бұрын
$60 to a welder and he'll make something better, I think.
@coachgeo19 күн бұрын
that jack is same as harbor freight Pittsburgh. Anyway.. about to do same thing but only transfer case... Can one spin the turn handle off and red locktight it? Same for the nut at end of all thread. can the bar stock with hole it it that the allthread goes into come out for access to the weld around top of that fat pin? I dont have hole saw or a saber saw...... got figure out a way to grind that inner weld off (have grinder- but maybe that will have not fit in there to grind the weld out anyway... The old shoulders of mine can not just heave how a T-case into place... let go of one hand and thread something w/out it dropping on my empty-ish cranium or ribs lol. Granted cEventually someone will smell it and come drag away my meat and bones if I tried.
@wrenchwranglers19 күн бұрын
@@coachgeo, I did go over some of this in the sequel to this video, where I pulled a 4x4 trans and transfer case with this. I ran a roll pin through the handle and I think used a jam nut on the lower end. I pulled the trans and transfer case as one assembly, but if one were pulling just the transfer case I think it would work ok, and at least make sure the neighbors don’t have to put up with a bad smell before emergency services discovers you. As fas as getting in there to the weld, the parts that need to come off to access it don’t really come off. A dremel might fit in there, or a long grinding attachment on a drill. Might take a while, but it could work.
@coachgeo19 күн бұрын
@@wrenchwranglers yes I saw it.... I dont have tooling to put in a roll pin or use the jig nor a saber saw... hence my questions above. Sorry for not being clear on that. drat on those parts not coming off... figured there was method to your madness on why you didn't go that route yourself
@coachgeo18 күн бұрын
@@wrenchwranglers now that I think about it.... will explore, after cutting off the post- just drilling a hole in each corner for bolts and nut/bolt it on. No messing with trying to get that center out. maybe will need thread the holes drilled into the bracket Jack's pad threads into.
@wrenchwranglers18 күн бұрын
@@coachgeo that could work. You’ll lose the ability to spin the top relative to the jack below it, but for lightweight uses that should work ok.