Follow me as i install my topkits with side pullers, ive never done it before....wish me luck!
Пікірлер: 113
@andyseago19282 жыл бұрын
Tip for you that I use. When drilling into the section place a length of wooden dowel rod up inside. It helps support the section and will stop you drilling through the other side if you are a bit heavy handed.
@AverageAngler2 жыл бұрын
Thanks, good idea😊👍
@petepattaya38653 жыл бұрын
Thanks for the tips on how to do the wraps , I bought the repair kit off ebay and did 7 kits with loads to spare , so it's a really cheap way to do them , and it was also really easy to do , would recommend anybody to have a go , cheers.
@adiem16532 жыл бұрын
Did 4 over the weekend a bit of a pain in the rear with the carbon ends always coming loose but got there in the end. I only had a small bit of the clear tape in the kit I bought - ran out quickly so the last kit I had to use electrical tape backwards - worked fine. Once the resin had gone off and I removed the tape it needed a light wet n dry sanding to smooth a few rough ridges. Keyed the whole repair and gave a light coat of resin to smooth it all out - end result nice lovely smooth and glossy finish.
@AverageAngler2 жыл бұрын
If you rub the wrap down a bit, a coat of lacquer gives a nice finish.
@andrewknotts7036 Жыл бұрын
Thanks fella this video gave me the confidence to fit MAP pullers to 10 of my top-kits and worked a treat, even repaired a few cracks too !!
@AverageAngler Жыл бұрын
😊😊😊😊Well done nothing stopping you now👍
@JaseNico33103 жыл бұрын
Bang on this mate..been doing my own repairs for a while now and they do get better the more you do! Key is to take your time!!
@AverageAngler3 жыл бұрын
Thanks
@iang9533 жыл бұрын
Slipping a piece of dowel in the section when you drill stops all the worries of hitting the other side and the drill bit pulling in. Nice job pal
@AverageAngler3 жыл бұрын
Good idea that, if I do any more I will be doing that👍.
@Adam-hr7vs3 жыл бұрын
@@AverageAngler I was thinking of sliding in a bamboo cane...
@matthewralph643727 күн бұрын
Good explanation and filming...Will be attempting this
@AverageAngler26 күн бұрын
Don't know how much the side pullers cost now, been a couple of years since I made this, but will still work😊👍
@heathfairbrother30723 жыл бұрын
Hi john I sand my pole repairs blend them in then lacker them it gives you a lovely finish. Great video john 👍
@AverageAngler3 жыл бұрын
What do you use for lacker, I would probably have done that if I had some lacker.
@heathfairbrother30723 жыл бұрын
Hi john I us autotek lacquer from the car when youve flated them off with different grades of sand paper and wet &dry it will look dull till you lacquer them you will get a nice smooth finish john
@mbench41742 жыл бұрын
Brilliant. Been doing mine same as this. Laquer for a smooth looking finish but not essential. Good tutorial.
@AverageAngler2 жыл бұрын
😊👍
@laniVargas-iy3lg6 ай бұрын
Thank you for the advice. Excellent video
@AverageAngler6 ай бұрын
Thanks
@markoxley76344 ай бұрын
Really good informative video, with laughter chucked in for good measures, cheers guy's
@AverageAngler4 ай бұрын
Thanks for watching😊👍
@pauruta Жыл бұрын
I use a piece of hose pipe, inside the pole section. Then when you drill or use a mounted point, you can not go through to the other wall of the pole section
@AverageAngler Жыл бұрын
A great idea, 👍. Thanks Paul😊
@adiem16532 жыл бұрын
Good stuff. You inspired me to get some carbon fibre and resin and a few MAP side pullers to have a go now. I can't believe how awful that carbon fibre is to work with. You cut it nicely then the slightest sideways movement pops the edge strands out then it gets worse from there!
@AverageAngler2 жыл бұрын
Yes it can be tricky stuff😊👍
@domgarofalo43353 жыл бұрын
Great video mate - my kit got delivered today so will be doing this at the weekend! Your video will be my tutorial!
@AverageAngler3 жыл бұрын
Good luck😊👍
@domgarofalo43353 жыл бұрын
Went really well all kits were a doddle to do, fitted vespe side pullers and caught carp and barbel to 5 pounds last weekend. Looking back I don’t know how I used to only fish solids with no puller!
@AverageAngler3 жыл бұрын
@@domgarofalo4335 brilliant, I've been using mine too. No problem 😊👍yet. Glad I made the video now lots of people having a go at it😊👍.
@johnturner70453 жыл бұрын
Brilliant video 👍. I'm going to have s go myself doing something like ten top kits I've got. Easy as step by step instructions.
@AverageAngler3 жыл бұрын
Let me know how you get on👍
@brianwelbourne98962 жыл бұрын
I am lazy and just slide a piece of an old pole down the top kit to the place I need it. Glue it.You now have as really strong section to drill into. Yes a bit sticks up but a bit of masking tape over it does the trick. It works honest.!
@AverageAngler2 жыл бұрын
Whatever works, works 😊👍
@gedmccarthy33663 жыл бұрын
Brilliant vid, just wrapped my first attempt at a puller as it looked so easy. Thanks.
@AverageAngler3 жыл бұрын
It's easy when you know how👍, thanks for watching.
@BaggieBob3 жыл бұрын
Great to meet you at the fantastic Acorn fishery watched your video today! Great watch see you next year 😂
@AverageAngler3 жыл бұрын
Like wise great to meet you, it's great to meet people who are watching the videos😊👍
@Adam-hr7vs3 жыл бұрын
Why did you decide to omit the hair dryer heat shrink process on the heat shrink tape that consolidates the resin & fibres into 1? If you miss this, you will be left with an uncompressed, softer, weaker, rougher finish with loose fibres.
@AverageAngler3 жыл бұрын
Tape provided with the kit I use, does not shrink when heated. You have to apply quite a bit of pressure when wrapping, my finish has always been good😊. You can get kits with shrink tape and use a heat gun if you wish👍.
@Adam-hr7vs3 жыл бұрын
@@AverageAngler Maybe you have forgot your own video. At 27-29 mins you criticise your own finish and start sanding the rough bits/steps. I would recommend using the heat shrink tape. You can only put so much pressure on with the tape unless its shrink tape because your tape will have no elasticity to produce tension. You could go over the clear tape with stretched insulation tape afterwards to provide some of the missing compression. Your windings are far too spread out too. If you look at the spirals on a professional pole, they are only 3mm apart. This is because the tape is 90% overlapped with only a 3mm offset from the last wrap. If you did this you'd get a higher pressure and better finish. It's like 10 elastic bands round your fingers will crush them more than 1 elastic band. Please don't take this as criticism - it's positive advise and we're all here to learn. You can also reduce the fraying - cut the length parallel to the mesh and you'd have fewer stray ends to combat. Also, keep the cloth in a long length and rotate the pole until you have a double wrap, then cut it to length. This way you can keep the tension on the cloth without accidently pulling off the last strands. I showed the composite dept at my work what I wanted done to my poles - the above is what they said - it's good positive advice!
@ggwildlife3 жыл бұрын
excellent tutorial keeping in my faves.
@johnwhitehead48092 жыл бұрын
thanks for the tutorial, just received my kit big help cheers.
@AverageAngler2 жыл бұрын
Hope it all goes well, defo use a bit of glue on the side puller bushes, some of mine worked loose over time, so I have glued them now😊👍
@retro-ogre3334 Жыл бұрын
Awesome job want to try this myself
@AverageAngler Жыл бұрын
It's easy as long as you are organised, 👍😊, I suspect price of bushes gone up since I made this, been a couple.of years ago now!......Thanks for watching
@brownie34983 жыл бұрын
Had a go at mine over the weekend turned out really well tbh thanks for the great vid if it wasn't for this if have probs never had a go haha
@AverageAngler3 жыл бұрын
Glad to here mate, hope you bag up! with them! Tight lines😊
@1dowsey3 жыл бұрын
Absolutely fantastic I’ve ordered everything and I’m already nervous about doing my first one and I’ve got 10 to do. Quick question would you consider super glueing the MAP puller in or are you happy as it is. Thank you so much for doing this video it’s a massive help 🎣👌
@AverageAngler3 жыл бұрын
Glue them, since doing the video, some of mine have come a bit loose and I have needed to glue them👍
@jilldavies3467 Жыл бұрын
Can a old pole section be used cut off at the correct position be used.
@AverageAngler Жыл бұрын
Do you mean use it as a sleeve? Could work but I'm not sure how easy that would be??
@BazAmanda603 жыл бұрын
Brilliant think ive been inspired to have a go .
@AverageAngler3 жыл бұрын
😊👍
@azertyy39782 жыл бұрын
Great video! I am considering doing this to my topkits. I also found this on the internet, not sure if it will be the same in strength as the carbon wrap. = Vespe stripper side puller + wrap - DRILL 6.0MM
@AverageAngler2 жыл бұрын
They work well just need to check they are correct for your pole, don't fit all models😊👍.
@azertyy39782 жыл бұрын
@@AverageAngler Thank you very much, I will give the Vespe a try. If it doesn't work out I will do the carbon wrap. :) I have another question, I see that you mainly fish with the feeder. Do you have experience with Preston poles?
@AverageAngler2 жыл бұрын
I have never used a preston pole, I mainly use garbolino now, so I have very little experience with them.
@Adam-hr7vs3 жыл бұрын
On eBay & other sites, they sell carbon tubes in 300mm lengths. What do you think about sliding a 50mm sleeve down the pole and gluing into place? I note that there's another video where vespe supply a 'pulla' sleeve that looks nothing more that 20mm plastic conduit that you can buy at wickes at £1.30 for 2m.
@AverageAngler3 жыл бұрын
I wouldn't be doing anything like that, the plastic tube or carbon would need to match the taper of the top kit I should think? The carbon wrap is the lightest way to do it and will definitely work if done properly. You wouldn't want to snap your top kit, would be a false economy.
@Adam-hr7vs3 жыл бұрын
@@AverageAngler Good discussion... to make it clear - I'm not arguing... just thinking aloud with respect to the title "CHEAPEST WAY TO GET SIDE PULLERS"... I have no doubt that a professional carbon wrap is the cleanest way to go. It's just a question of whether quicker cheaper alternatives work just as well with no degradation of function and look much more tidy. People have 'sleeve' repaired sections for years with great success and 'whipped' over it. Even the top of multi-tip feeder rods simply have 2" piece of of carbon reversed and glued in to take the tips. Every joint on a rod/pole is a 'sleeve' that takes a hammering and they're not even glued! Vespe have sold out of 5 million plastic 'plastic conduit style' kits with no issues and I know many people that have slid a piece of carbon sleeve over to fit a puller with no issues. With respect to you taper concern (both carbon & plastic tube), over a 40mm sleeve length, my vernier caliper does indeed a indicate a difference of circa 0.1mm due to the taper and it was also a concern of mine. However, last week I put a sleeve on an scrap #2 pole section, put a dab of superglue on the 0.1mm 'open/gap end' and the glue disappeared and filled the gap with capillary action - looks amazingly neat where the glue created a radius between the pole and sleeve. The glue went in just like watching a soldered pipe fitting. I fitted a puller bung and fed a bike brake cable with a 'pip' at the end through the pole section. I then held the section vertically above my 18kg bike and lifted it with no issues. This is a unrealistic equivalent to lifting a 40lb carp - so it passed my test! Note that the conduit is the tough stuff that they use to protect vulnerable external mains electrical cables. You could stamp on it (unlike a pole)! If you said that it weighed 1g more or is 1mm bulkier, I'd not argue with you - although it felt better to grip in the hand. Using some poundland superglue and a piece of conduit and a pipe cutter that I already have, I think that I could fit around twenty in one hour with a total of £2.30 worth of materials. Having read the details, what do you think now?
@AverageAngler3 жыл бұрын
👍
@Adam-hr7vs3 жыл бұрын
@@AverageAngler Thanks. Is your 'thumbs up' your concurrence that you are happy with the above idea and retract your previous concerns?
@AverageAngler3 жыл бұрын
Why don't you speak to the composite materials experts where you work, see what they think of your idea? I'm not a carbon fibre expert just a fisherman😊.
@Adam-hr7vs3 жыл бұрын
Great video. Is there anything you'd do different if you did it again? Do you think it would be possible to 'mask' either side of the wrap maybe with the clear tape 1st to get a neat edge with less resin overspill? It appears that any other type of tape may not come off so cleanly?
@AverageAngler3 жыл бұрын
Use even less resin I think, and glue those side puller bushes in😊👍.
@bayrischefischerei2591 Жыл бұрын
I had a question can you tell me what kind of clear band this is which you use to fix ?
@AverageAngler Жыл бұрын
Do you mean the clear tape? I do not know I buy it as a kit, link in description I think?
@bayrischefischerei2591 Жыл бұрын
Yes , thats what i mean is it just a foil or is it stuck on one side ? Ok thanks
@AverageAngler Жыл бұрын
It is a clear plastic, it does not stick in any way.
@peterstephens5438 Жыл бұрын
I would like to put the map side pullers on my pole our far up pole do I put them a carp cruncher and diaw 3:12
@AverageAngler Жыл бұрын
It's best to put them where they would sit nicely for you to strip whilst playing a fish. So hold the top kit like you would when playing a fish and see where your hand could easily grab the elastic🙂👍
@keithbrown69903 жыл бұрын
Nice 👍 thanks
@paulsomersetwolf59702 жыл бұрын
Hi John just watched this again and have decided to have a go myself have ordered the kit all mine at the moment are end pullers which are fine but these look to be neat It's the drilling I'm not confident with but will take my time. How far up the section do have the pullers to be around 10 - 12 inches would that be about right? do you rate the map pullers? Over the Preston is there any advantage? Great vid though tight lines👍🎣
@AverageAngler2 жыл бұрын
I have had a few of the map pullers pop out, so a little glue is a good idea. The preston rollers need a bigger hole, but you do get a roller with their one. As for location, think about where you will hold the kit when playing fish. You want the puller to be close to the hand on the pole, so you can grab the elastic easily. Also if you have to wrap to far up the section you will lose elastic length, which is another consideration. I've had no serious issues with mine and its been over 6 months since I did them, hope it all works out for you👍
@paulsomersetwolf59702 жыл бұрын
@@AverageAngler thanks for your reply John is there much difference in having the roller one to the map do they work the same! It certainly is a saving doing it yourself than getting it done professionally thanks again for the help I may contact you if I get stuck doing them 🤣 keep the great vids coming 👍
@AverageAngler2 жыл бұрын
@@paulsomersetwolf5970 I have a kit with a preston roller in that I bought second hand, I don't personally notice any real difference. Other people do prefer the preston ones, I suppose it's all personal preference. I havnt seen Anything I would call a real advantage go with the map rollers they are a good price 👍
@widnesac Жыл бұрын
Map need to be glued in or they'll keep falling out. Preston by far the best
@Esoxluciouss113 жыл бұрын
great job, ty for sharing
@AverageAngler3 жыл бұрын
😊👍
@mcmozz3 жыл бұрын
Hi mate I'm about to do a margin pole, I've bought the repair kit, pullers etc just wondered what width of wrap you used, is there any recommendation for the wrap size?, Also the measure from the end to the third section? Thanks
@AverageAngler3 жыл бұрын
About 4inch wide would be more than enough. Best thing regarding distance from end of the kit, just think where you would want it when you are playing the fish.
@AverageAngler3 жыл бұрын
I think I do measure the width of my wrap on the video? Might be 2 inches??
@AverageAngler3 жыл бұрын
Hi Matthew just rereading my comments if you are doing puller wrap then 2 or 3 inches, if it's a section repair 6inches.
@josephhutchinson8121 Жыл бұрын
Nice one
@AverageAngler Жыл бұрын
Thanks for watching Joseph
@MegaAndy1803 жыл бұрын
cracking vid m8
@AverageAngler3 жыл бұрын
😊👍
@paulsomersetwolf59702 жыл бұрын
Hi john just in the middle of doing my side pullers I've checked them after 2+hours and they are tacky but can't get the wrap to stick would it be I haven't put enough of the formula on I only put it on thin or do I need to wait longer getting worried now?
@AverageAngler2 жыл бұрын
Probably gotta wait a bit longer, all depends on temperature and ratio of hardener. Good luck👍
@paulsomersetwolf59702 жыл бұрын
@@AverageAngler It get tacky but the wrap won't hold don't know what to do now with the sections will i have to rub it all down again you made it look so easy?
@AverageAngler2 жыл бұрын
@@paulsomersetwolf5970 it should hold, it won't be a mega strong hold just enough so it clings to the section. Are you doing it in the house not in a cold shed or garage.
@paulsomersetwolf59702 жыл бұрын
@@AverageAngler in my garage but let them dry in the house it was tacky but left it for 4 hours but watching yours when laying the sheet on the part it just stuck but when I started to go around the section it just wouldn't stay it flicked up where I started so I gave in will I have to sand them down again to restart theres not loads on which may have been why it didn't work?
@AverageAngler2 жыл бұрын
Sounds like you were nearly there, sometimes it doesn't stick so well, but you can stop the end curling up by wetting it with the resin on the brush. I tend to just start it on the tacky stuff and kind of brush it on with a wet brush(wet with resin). I would rub it down a little before retrying don't go mad though.
@alanatkins18783 жыл бұрын
Where did you get your fibre glass repair kit from
@AverageAngler3 жыл бұрын
It's a carbon fibre repair kit, from polerepairs.co.uk😊👍
@alanatkins18783 жыл бұрын
@@AverageAngler thanx
@scottpardoe63492 жыл бұрын
How are these holding up mate?
@AverageAngler2 жыл бұрын
They were working fine, I have now upgraded pole and have some newer top kits. I isn't upgrade because of the kits they are still fab.
@scottpardoe63492 жыл бұрын
@@AverageAngler thanks, priced it up not using one of those pre packed kits and it's much cheaper.
@ianlivingston58026 күн бұрын
Too much hassle , It would have been much easier to have bought a make of pole with the puller kits already fitted. Like I did.
@AverageAngler5 күн бұрын
True but they didn't always come with side pullers, So if you had £600 worth of older top kits might think differently😊👍