Chevrolet Trailblazer Valve Cover Gasket Replacement - How To Repair Oil Leak

Chevrolet Trailblazer Valve Cover Gasket Replacement - How To Repair Oil Leak. Today we replaced the valve cover gasket on an 05 Chevy Trailblazer 4.2 I6 Engine. Valve cover, Intake and Coil bolts are torqued to 89 lb/in. Thanks for watching!
DON'T FOEGET TO CHECK OUT DMONEY GARAGE FACEBOOK PAGE(link below). posts related to what's upcoming and what else we worked on that didn't land on youtube!
Merch: www.teespring....
Parts:
Valve Cover Gasket: amzn.to/2Fve03M
Intake Gaskets: amzn.to/3kqqgBf
Tools:
Socket Set: amzn.to/3c9Vslw
Trim Tools: amzn.to/3c5WD58
Torque Wrench: amzn.to/3hA0FEh
Social Network Links:
Website: www.dmoneygarage.com
Facebook Page "DMoney Garage" @dmoneygarage www.facebook.c...
Instagram: thegaragesteve3
Contact Email: [e-mail]
Notice:
Due to factors beyond the control of DMoney Garage, it cannot guarantee against unauthorized modifications of this information, or improper use of this information. DMoney Garage assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. DMoney Garage recommends safe practices when working with power tools, automotive lifts, lifting tools, jack stands, electrical equipment, blunt instruments, chemicals, lubricants, or any other tools or equipment seen or implied in this video. Due to factors beyond the control of DMoney Garage, no information contained in this video shall create any express or implied warranty or guarantee of any particular result. Any injury, damage or loss that may result from improper use of any tools, equipment, or information contained in this video is the sole responsibility of the user and not DMoney Garage.
Credits:
Music: www.bensound.com
Intro & Outro: www.fiverr.com
"Steve Demo is a participant in Amazon EU Associates Programme, an affiliate advertising programme designed to provide a means for sites to earn advertising fees by advertising and linking to DMoney Garage"

[@jenniferpowell9837]

I'm a 40 year old single momma and I've had to do this job and others myself. This video walked me all the way through, start to finish. I appreciate these videos sincerely. Thanks for making this possible.

[@mvc2177]

Gonna give you props. One of the hardest valve cover jobs I’ve done myself

[@ianconley6673]

Us men are good for something now and then 😂

[@zkonrad420]

This video just saved me $600! Just a do-it-yourselfer here, shop quoted for 6 hrs, I did in in 6 with the help of this video. Took me almost 2 hours just to get the 10 bolts off the intake manifold, lol.

[@LarryDawson57]

Thank you so much! This is my very soon project and one I now dread LOL. Makes me miss my teen years in the late 60 and early 70s, Those valve cover gaskets were a 30 min job.

[@carolynmorton6903]

Video is so fantastic that this girl got it done!! Couple notes.. buy a little hose on the intake and just cut the old out if the way.. it breaks anyway. Second, firewall bolt no problem is a Mini ratchet, short extension and regular 10mm socket… the trick for me was to step on a stool to get over the top comfortable enough to get to it 👍 no worries following this video. Thank you soooo much!’

[@ianconley6673]

Good job mama 👏 😂

[@sasquatchish]

Same instruction can work for Yukon XL. Just a few more AC parts and such. You fixed my truck! This is one of the BEST mechanic videos on KZbin. PERIOD. Simple quick no bullshit. I just watched a few times while having some drinks and repaired my truck. F**** the center bolt on the intake though~!

[@giaellington1276]

Your instructions made me feel comfortable doing the job myself after paying someone to do the job and my valve covers are still leaking. I like all your detailed instructions. I keep this video right by my side because I had to refer to it constantly.

[@ChrisHisWickedness]

At one point I said out loud, "I love this guy." Thank you for this video, without it, I'd either take my Trailblazer to a shop ($$$) or struggle even harder to get this done. Thanks again. Liked and subscribed

[@sarahvest5693]

12 minutes in the video took me 2 hours but I’m almost there !

[@JackMoveShawty]

2 hours don't seem bad. I gotta do this today so if you took 2 hours I'm looking about 3.5-4 hours which still ain't that bad. Hopefully I can do it

[@ScottFalcon-ui6pe]

What r u slow poke Majoe. My 5 year old grandson did my valve gasket in 30 minutes. He stood on a step stool and I had to break loose several bolts because he is just not strong enough yet at 5. Do you need help breaking loose bolts too?

[@keithll3283]

Fantastic video, very helpful. A few things I found: 1)don't fear that rear-most bolt. If you sort of lay on top of the motor you can feel it with your left hand and easily guide a 1/4" drive socket on a swivel onto it with just a ~3" extension. I thought this bolt would be a nightmare and it was actually very easy 2)the studs for the PCM come out with a 4mm socket, but use caution. I preferred having those studs gone when removing and installing the intake manifold 3)the hose that obscures the "hidden" bolt in the center of the manifold can be removed on the bench (or perhaps in the vehicle) if you heat it with a heat gun. I did this on the bench (also needed to retrieve my socket that had become trapped LOL) and just disconnected the bottom, making installation MUCH easier. The hose slid back into place by hand easily, although I used some WD40 to increase my odds of sliding it back into place with no drama

[@garymaddux2000]

NOTE: for some models (or all, I'm not sure), there is a couple of wires that go all the way down the passenger side of the motor, and back to the front diff actuator. It took me about 10 mins to find it. Only accessible from the bottom of the truck as its on the back side of the oil pan. I didn't see that in this video, so I thought I'd just make a note of it. 😊 thanks for the video buddy. I used this as I was doing the job. Very helpful

[@DMoneyGarage]

Thanks for adding that. I’ve had a coupe with that now that you mention it(forgot to say something in the video). Thanks

[@ffigueroamatt419]

Just by starting off your very detailed. Thanks for taking the time for all of us. I'm getting the courage to do it myself and save me 800$

[@benjaminbobadilla9379]

Dude. Best video on working on the top end of the 4.2 Chevy i6 block awesome job

[@noelabrado1406]

This video is the definition of helpful. Its really detailed, saved me a lot of money. Great stuff!

[@KyleGreenhow]

This blows my mind, years ago, my inlaws had a trailblazer and it needed this job done, i looked at it and after trying for a while to figure out how to do this, i gave up and told them sorry, you have to take it in, what blows my mind, is that people think this is ok, this is the kind of crap i have seen time and time again from GM, getting a intake manifold and valve cover gasket off shouldn't be this hard, this is stupid! For all you GM lovers out there, have fun with stuff like this, but for me, its sayonara!

[@KnightOfChrist1978]

That's what they do. They get all there great minds in one room and say ok we need we need 2 things one shit don't need to last and 2 make it as hard as possible to take apart lol

[@richardsmith6769]

Great instructions, now I will allow a couple of days to get it done.

[@mvc2177]

Really appreciate your video. Hardest part for me was the manifold bolts, bottom alternator bolt, and bracket removal attached to the manifold. I didn’t even know there was a bolt behind the hose on the manifold till I rewinded your video. Million thanks

[@Tony-rl2fr]

Probably the best DIY video on KZbin. Great job, thank you. Hope to sell mine before I ever have to go through this, 😆.

[@MrBigR928]

I bought my 2005 Trailblazer last year & I just changed the sparkplugs today. Even though it was running smoothly, I just changed the oil & air filter yesterday & I was just gonna change the plugs outta GP so I can see what's going on in there! I had three plugs that were a little wet around the sides but none on the electrodes ( Iridium's) but they were the original plugs & I bought it at 124,000 & I'm at 133,000 now. The plugs were the original plugs that came from the factory because the part numbers were old & they were worn but not done which is a very good thing considering the age! A little old man up in Canton Georgia had it & garage kept & she looks good! Clean with no rust! The coils were all dry but I figure to be doing this job pretty soon 😭 Thanks for the video & now I know what to do unless I pay my mechanic & I'll sit in the lounge watching TV 😁

[@flyboy2610]

15:00 That stiff hose is part of the PCV system. It can be a real pain to remove! There is a spring clamp, like the OEM radiator hose clamps but smaller, on the end of the hose next to that 10mm bolt. It's bonded to the hose. What I did was use a small pair of needle nose locking pliers and open up that clamp. Then the short end of the hose can be pulled off, and the long end will come right off the intake manifold. Remove that spring clamp from the hose and just use a small worm drive hose clamp. Makes removal much easier next time! You can see that clamp at 16:55.

[@tuscani915]

Just used this how-to and it took me about 1 1/2 hours to get this removed. Still waiting on the parts to get in just wanted to get a jump on this. Thanks for the great detailed how-to.

[@oscarperez1345]

This video save me a lot of money but gave me a headache because it was my first time doing this. After my dad told me the engine coils were oily, we knew it was going to cost a lot.

[@speed1826]

Man I’m replacing my valve cover gasket and I was coming from the drive wheel well and I was fighting for like a hour and i decided to look for a video and I found urs thanks a lot

[@DMoneyGarage]

Glad it helped!

[@carloscubillos6159]

Thanks, very good video. No too much videos about this gasker replace. It was very informative.

[@mvc2177]

I’ve done plenty of valve covers gaskets on many vehicles and this is my first time doing it on a trailblazer. This is one of the toughest ones I’ve done. Getting every gasket replaced while I am in there

[@dynamic1964]

Thanks for a great video, you saved lot of time for me. Had some oil in the fifth plug hole when I serviced my 02 Bravada, and now three month later I have a fifth cylinder misfire. Thumbs up!

[@jonnatancontreras1425]

Everyone is tasking the same job around the same time 🤣 a little fishy, but I am tackling this tomorrow and the day after wish me luck!

[@DMoneyGarage]

I'm guessing so. Lol. You got this!! One step at a time!

[@jonnatancontreras1425]

@@DMoneyGarage my lord I couldn’t even read what I had said lol. But thank you! Doing it right now

[@huntert6452]

Shit I just discovered my leak too right at about 215k 🤣

[@carljdipietro]

Nice job buddy, you make it look so easy, and your instructions are so clear. Thank you.

[@vapewilder7843]

I wish I knew my way around this engine as well as you do. Very impressive.

[@blastedlife4205]

I literally just had my valve cover gasket blow like 20 mins ago took off the entire intake at my girls apartment took the whole thing apart dried the seals and re lubed em and reinstalled fixed the issue

[@majjr8]

Great detailed video. 30 minutes well spent

[@jewski27]

Thanks for the video, I watched another video and the guy was taking extra stuff off that you don't need to and was not very explainable. Came across your video and now I know what I'm doing when I get ready to do my daughters trailblazer.

[@manieflatlinefresh]

I like how you break the tutorial part down for us new mechanics gratitude 🙏🏾

[@0matthewzero]

This is a huge help. Thank you for making this video.

[@joelsinga]

I watched this video some time ago and now I finally get to do this job. Oh boy I can't wait but thank goodness for this amazing video or I would be lost. Thank you very much and wish me luck!

[@toddlawson3325]

Yea I can't wait to start this job lol I didn't know what I got myself into

[@RobertoSantiagoRodriguez]

Wow, great video! It is ridiculous to go through so much work for valve cover gaskets, though! Tx so much

[@iGame2A]

I finally did my TB ... ran good for a day now I'm getting p0030 and misfires on cylinder 2 and 3... going to have to do some testing this weekend

[@danielromo2110]

Check your plugs and see if any oil made it in any of the packs

[@iGame2A]

@@danielromo2110 I did ... they are clean. I replaced all the gaskets on the valve cover. I'm about to swap out the ignition coil to see if the coils need replacing.

[@iGame2A]

@@danielromo2110 I also replaced all the plugs

[@madisonhenninger2943]

Damn thank you so much for showing me where the long green plug went on the on the passenger side by the oil filter! Try to figure it out for hours now

[@wyked_079]

Amazing video! I have to do mine due to misfire and oil in the spark plugs. I know mine will not go as smooth as you made it look. Wish me luck!!!

[@DMoneyGarage]

You got this!!! If you believe you can do it then you can do it!! Let me know when you get it done!!!

[@wyked_079]

I followed your video step by step pausing in between your instructions. Worked out amazing. Thank you for the tips on the 2 hardest bolts holding on the intake. Saved me a ton of time. Thanks again for posting this video. You saved me $625.00 which was quoted to me from my local auto shop. Thanks again.

[@DMoneyGarage]

Glad you got it done and everything worked out. Thats why I post the videos😁

[@hannahmcintire718]

I have the same issue on my 05 Trailblazer. just need to find the time now.

[@kencooley5589]

I just did this for my neighbor, we did intake manifold gaskets too cuz why not. But that bolt against the firewall I used a 10mm deep with a 3/8 ratchet and no extension. Then I put a steel rod on the handle and tapped it down with a mallet to break the bolt free and then spun it off.

[@DMoneyGarage]

Nice. Definitely other ways to get it. Lol. I'll try that on the next one. Thanks.

[@kencooley5589]

@@DMoneyGarage thank you for the video though, I knew where all the bolts were before taking anything off and that makes the job much smoother

[@DMoneyGarage]

That it does. Thanks!

[@SnubBarracuda]

This video was very well done. Not a lot of them on KZbin so I'm lucky you did this on one of my cars, lol. Anyways thanks, man.

[@osopolar8711]

I will do it with this instructions, Thanks a lot the best video. I'm from Mexico I send you greetings.

[@cesarmartinez3582]

Great job. I have cuestion I have trailblazer 2005 and oil is Goin to water . N water Goin to oil you think is intake gasket or head gasket??

[@RA-uy3er]

Awesome video this does nothing without explaining what his doing..thank you for a great lesson.

[@huntert6452]

Might as well do my motor mounts and intake gaskets too

[@alexhall3373]

I just did the Moter mounts and still turned out to be a pain

[@frankcarey6505]

About to so mine too

[@aperez_1574]

Would I have to replace the spark plugs even if they’re a couple months old? Along with the coils ?

[@tiffanyc6011]

Love this video! Great job! It walked me threw mine that i am doing now. ONLY issue is you don't torque them to 89ft lbs they are supposed to torque to 18 ft lbs. But my issue is my bolts keep snapping before i even get to 18dt lbs! Any help js much appreciated.

[@blacksteel10]

Give ‘em an inch and they’ll take a foot! 😂

[@lazeralchemist5492]

Great video! Thank you for posting.

[@autooutlet1563]

Yea this was not fun to do at home, but it’s done!

[@may03LT]

thanks for this video trailvoy needs help BAD!

[@elkcrazy28]

Doing this tomorrow. Very helpful.

[@JimmyHinton]

I found it was easier using a nut driver on most of the intake bolts. Still struggled with the last bolt. But wasn't too bad.

[@mariochuqui746]

Hi, good job? Question? So for the trailblazer 2002 ext are those smaller sizes gasket for each coil right? Is not like the other models biger long gasket for the valve cover gasket? For this car those valve cocer gasket are diferent right? No need silicone? For extra safety ? I got one valve cover gasket the oil are starting to leak all around in the passanger side is getting wet there. So i am triying to do this car sooner this weekend may be. Thank you !!!

[@adrianzamora6785]

Hello..where did you get the pump to suck the oil from the spark plugs?

[@JackMoveShawty]

This is a very good video. I need to replace the valve cover gaskets BUT it looks like a lot of work & that bolt by the firewall is going to be the hardest thing to do. I'm just not sure I have what it takes to get this job done.

[@TheCodesterr]

I hear you … this looks like a weeks worth of a project. Working full time and doing this might be killer. Pushing 235k miles on mine.

[@JackMoveShawty]

@@TheCodesterr well with everything I did, it took me roughly 6 hours. I'm not mechanic but pretty handy. This video did help tremendously.

[@TheCodesterr]

@@JackMoveShawty oh nice that seems really quick! I would say I’m handy too, but would really take my time on it to make sure the intake didn’t break or anything. So you ended up replacing it and everything is working now??

[@JackMoveShawty]

@@TheCodesterr yes I replaced the valve cover gasket & the spark plug rings (I guess that's what it's called) & everything is working great. One thing I did mess up on was torque when righting the valve cover screws. I don't have a torque wrench, I was just using my ratchet set & over tighten one of the screw & broke it off inside the hole. Now I have to spend time one day to get that stem extracted out & replace that screw. But even with breaking that screw, everything is working great. No leaks because I guess the rest of the screws were so snug it mad a complete seal. I have no real complaints.

[@TheCodesterr]

@@JackMoveShawty phew, thankfully that sealed it up for you!! Ive been reading it’s common for the bolts to snap on the intake manifold… did you have any issues with that?

[@jalton9416]

Very good video. Great step by step directions.

[@FranciscoPerez-ls2bl]

Thank you for the video it is really helpful, you make it look so easy. Nice and clean job.

[@TheCodesterr]

Thanks boss. Phew this is labor intensive…

[@ellingtonsk]

Excellent presentation Sir!

[@snickers6736]

What tools do you use to remove the hoses?

[@MXstar189]

find the leaky one then suck what you can out with rags, clean with brake cleaner, then use permatex black rtv "right stuff" around where the plastic and aluminum meet... put back together. did this years ago

[@orangeboy9633]

Did you also replace the air intake manifold gasket too ?

[@DMoneyGarage]

Yes. All seals and gaskets were replaced.

[@boogerhead0]

May as well give the throttle valve/body a good washing while it is there in your hands.

[@DMoneyGarage]

It got a new one the next day. Figured I’d do the valve cover gasket then swap the body the next day. Lol

[@MrOnemanop]

After watching this, I think I'll just keep adding a quart of oil every 1,000 miles. Nicely done though.

[@jasonchioino1557]

It sucked lol

[@tracysnodgrass]

Lmao absolutely 🤣

[@danielbarker6971]

Yeah until the oil leak gets so bad that it's fouling spark plugs n misfiring

[@w829l5]

It looks hard but honestly, it's not.

[@shadowopsairman1583]

If you have that kind of leak as in video you will cause coil damage, misfires

[@OnlineAutoRepairVideos]

Bro, this has got to be the best video out there, and if you are doing all your videos like this, your channel will SKYROCKET!!! We are doing this job soon, and this video was PERFECT!! Definitely subscribing!!!!! By the way, my name is Tim! By the way, those few thumbs down you have must be from people who have NO IDEA how to work on cars!

[@DMoneyGarage]

Thank you!!!

[@irockhard9963]

I loved it, I think I can do myself now.

[@legitpaper8251]

I no one day minds will need changed as well because I just changed the plugs and seen a lil dryed up oil so do you think I might need to change minds to because I'm having a misfire on four but didn't see any oil on the cores packs so what you think I should do and great video by the way because I'm like it probably want be hard taken everything off my problem probably will be putting everything back on it but I'm sure it's gone save a lot of money.

[@DMoneyGarage]

If there is no oil in the hole, swap the coil with another cylinder and see if the misfire moves. Those coils go bad frequently also.

[@legitpaper8251]

Ok thanks

[@anguscolquhoun6899]

How did you torque the back bolt against the firewall?

[@DMoneyGarage]

Honestly the easiest way is the use the setup that you are using on the rear bolt and feel how tight another bolt is and then tighten the rear one to feel. I have a 1/4 inch torque wrench but its still a bear to torque it.

[@RedArrow73]

89 in-#; 10 Nm.

[@franciscogomez2565]

I’ve got a 2 pin connector right next to the fuel rail just hanging after putting everything back together I’m not sure where it goes…. Any idea?

[@glenthrall]

Thanks for sharing your awesome video! I have an 04 GMC envoy your Blazer is a clone of my engine! ? Also 🤔 can a leaky spark plug tube gasket and or valve cover gasket cause oil to deep in the cam shaft Senser solenoid as well? Also I'm replacing map sensor and cam positioning sensor as well. Thanks again Sir "D money🚙💨💨💨💨💨

[@glenthrall]

Not deep seep

[@jamincarr5673]

One more question. I finally have all the bolts loose on the manifold. It will not budge. Is this due to a gasket being stuck on good?

[@DMoneyGarage]

I’ve had to give it a good tap going towards the drivers side. They are rubber oring style seals so they have a tendency to get stuck. Make sure you got all the bolts first. Intakes aren’t cheap!

[@DanielRichards644]

that bracket you are removing at 3:56 is a USELESS bracket, I removed it to do something years ago and NEVER reinstalled it. Also I highly advise the use of a Ratcheting Wrench for removal of the lower Alternator Bolts.

[@sarahvest5693]

Thank you for this video it was huge help

[@juandiaz3205]

Is the same Gasquet. Of the water. Go inside of the oil engine? I need change the gasquet my truck is over hot over 20 minutes driving. 😢. I need fixing

[@georgechamberlainjr3168]

Any idea why my trail blazer would start rough and idle rough but then clear up and run decent after doin this job. All my wires are hooked back up. Every time i crank it over it starts really hard and still have a miss fire. Any ideas. Ill probably pull it all back aprt tomorrow. Thanks

[@PplCantDriveOkc]

just did this yesterday after vid, what a pain in the ass!! but I cleaned so called unserviceable pcv valve. no more leaking oil and oil pressure doesn't jump 20psi anymore, pcv, intake bolts were the worst part.. rest was ok

[@PplCantDriveOkc]

did valve cover gasket too. it and gaskets around plugs were dry af. crumbled when pulling out valve cover...

[@PplCantDriveOkc]

also only has 1 clean plug "hole" oil was seeping in all others.. wish I could show pic

[@jamesyarbrough4777]

just out of curiosity, how many miles were on the car and what oil and oil change interval (miles) were you using?

[@DMoneyGarage]

160k and after I started doing the maintenance for her I did every 4-5k with full synthetic

[@fuckcensorship69]

@@DMoneyGarage 5w 20?

[@alpinehs]

Fantastic video.

[@0matthewzero]

I just did this to my 03 trailblazer. I followed the steps you laid out. Very good video, It helped immensely. I thought I had followed the instructions perfectly, but when I went to start my trailblazer it turned over then stalled out immediately. When I tried to start it again it wouldn't start just the rapid clicking noise. I checked the fuses, & the PCM fuse had burned out "it wasn't burned out before. So I replaced that & now when I try to start it It just chugs for a little while Like it wants to start, but it not able to fully kick on. Can you think of anything I may have done wrong while making the repair that could cause this? Oh I originally changed the gaskets because my trailblazer started misfiring on cylinder 1, & I found a very small amount of oil in the cylinder.If you get a chance to respond I thank you. Again great video.

[@foxface16s58]

Maybe forgot to re connect a hoes or connect a sensor, my guess.

[@JoseDiaz-rm7ry]

Did you found out what was the problem same issue here with my trailblazer?

[@laykawest8674]

@@JoseDiaz-rm7rydid you figure out the issue ?

[@jamincarr5673]

Hey man quick question. When taking the intake manifold bolts out do they come all the way out? Mine come basically all the way out then stop and they can wiggle around and I can keep on loosening them and they just spin as easy as the air blows.

[@DMoneyGarage]

They stay with the intake. They are captured. They can be pulled out but don’t need to be. If the intake has been off before I’ve seen them not stay in the intake. Hope this answers your question.

[@jamincarr5673]

@@DMoneyGarage ty man I was getting frustrated. I was like what type of f’ing bolt just keeps on spinning but won’t come out. A cold natty light was keeping me cool headed though in the process😂 .. thanks again! Have a good one.

[@xder45100]

You have been a great help Thank you

[@TheCodesterr]

Do you think this is worth replacing on an 07 with 235k miles? No misfires on mine.. just a slow leak … not sure if it’s coming from coil packs and/or valve gasket. I replaced the spark plugs and if I remember correctly it wasn’t flooded with oil.. but could be wrong.

[@TheCodesterr]

Well… I did it and wow!!! What a job

[@fuckcensorship69]

@@TheCodesterr how bad was it? Is the truck still running

[@TheCodesterr]

@@fuckcensorship69 oh man this was def a doozy. I took my time, but a couple days plus an all nighter I accomplished it. No leaks through the coil packs now. Glad I did it though. I say go for it if you’re not needing a vehicle for a few days. It wasn’t hard, just gotta work a few bolts here and there and be patient. The intake was the hardest part. Def need the right tools

[@voidisyinyangvoidisyinyang885]

Wow this is genius.

[@dfreshnclean311]

What area are you in? I need this done.

[@esgarza1486]

Can this be causing rough idle and smoke coming out of the oil fill

[@DMoneyGarage]

Rough idle yes. Smoke from oil fill no

[@esgarza1486]

I have white smoke coming out of the oil fill and I have oil in spark plugs in changing the valve gasket s but wondering what the white smoke could be

[@esgarza1486]

I just did a oil and filter change two weeks ago also put on a brand new radiator vvt seloniod also don't know why there's smoke coming out of oil cap almost instantly

[@313dlo]

How do you remove the fuel line without that tool? Also, i have two fuel like lines right there

[@aPoorsPerspective]

they cam pos sensor connector is always tight on these trailblazers

[@DMoneyGarage]

Its about 50/50 for me. I always try against my better judgment 🤷‍♂️lol

[@alpinehs]

Excelent vídeo. Thank you for showing.✔️✔️✔️

[@efraindomingo5051]

Excelenrt. Video berry berry god! Thanks!

[@DMoneyGarage]

Thank you!!!

[@christopherdarden1859]

my mechanic said you dont have to take all that off. just move the pcm out the way.

[@DMoneyGarage]

Sure can. But I don't mind spending the extra 5 minutes to make more room🤷‍♂️.

[@mrkttrdr2919]

Nice job on replacing gasket, looking at the throttle body, would have taken it off while ur there to clean it, looked pretty nasty

[@DMoneyGarage]

It got replaced on a later repair due to dtc’s. Customer wanted the misfires fixed first. Customer didn’t have the money for the throttle body during this repair.

[@TheBigBleau]

is it completely necessary to undo all the connections on the passenger side of the motor?

[@DMoneyGarage]

No but the wires can be kinda tight getting the cover off. I do it because most of these are high mileage and wires can become weak. I do it to prevent broken wires.

[@TheBigBleau]

@@DMoneyGarage makes sense. thank you for letting me know

[@rogerwicksell]

whats the little hose called i tried to move it out the way and it broke :*)

[@ProjectCarTV]

nice

[@airsoftinfoguy]

Would that cyclinder be damaged from the oil leak?

[@DMoneyGarage]

Nope. Possible ignition coil damage but that’s it. If there isn’t any misfires I’ll clean the coils and put new plugs in with the repair. If it was misfiring I would replace the misfiring cylinders coil along with all plugs with the repair.

[@Miamiboi305]

Why did you have to take off the intake manifold I thought you can just remove throttle body?

[@tomm2271]

Hello, I have a very clean 2005 Envoy 144k. Simply replaced the plugs, easy. I stumbled on your video, omg what a mess. So is this an inevitable problem that I'm going to have to deal with some day? When removing coil #3, I noticed just a tiny bit of oil where the cover meets the head. Nothing like what you have here....not even close. Thanks Tom

[@DMoneyGarage]

Eventually you'll have to but hopefully not for a while. Lol

[@terrancethompson567]

Thanks for the video but in my opinion u took off way too much for just a simple gasket change. I only took off the computer..loosen top 2 bolts to alternator sliding it forward..that let me access to first air intake manifold bolt..the one in the back I used multiple ext...about 2ft If u have them like me...and went thru the wheel are for the far right intake bolt in the back by the heater hoses slid the whole unit to the left a lil and presto I can access the left side of the valve cover...all due to your direction though. God bless all and good luck 🙏

[@josuemartinez870]

Great video how long did it take???

[@DMoneyGarage]

I've done a few but usually takes me around 2 hours. I'm very meticulous with a customers vehicle. I would say a first time doer should have it done within a half a day but no more than a day. But if it takes longer that no biggie, take pride in doing it yourself and saving some cash!

[@josuemartinez870]

@@DMoneyGarage Thank you i will give it a try it’s nice learn 👍 😁

[@gflackoescobarofficial5921]

So I don’t need any RTV ?