Tap to unmute

Tired Of Mesh Bed Leveling? - Z Tilt Configuration - Klipper - Chris's Basement - 2024

  Рет қаралды 14,763

Chris Riley

Chris Riley

Күн бұрын

Пікірлер: 65
@TheElectronicDilettante
@TheElectronicDilettante 3 ай бұрын
Excellent video! It couldn’t have come at a better time. I was about to start pulling my hair out trying to fix a problem you sorted out in 20 minutes. Truly, thanks for sharing your time and hard work.
@ChrisRiley
@ChrisRiley Ай бұрын
I am glad it helped you out!
@alexisentonfire
@alexisentonfire 6 ай бұрын
you're videos are always super easy to follow, very nice!
@ChrisRiley
@ChrisRiley 6 ай бұрын
Happy to help! Thanks
@VincentGroenewold
@VincentGroenewold 6 ай бұрын
Thanks for another super useful video, always like these including the config, helped me out a ton in the beginning
@ChrisRiley
@ChrisRiley 6 ай бұрын
I'm glad I could help! Thanks for watching
@woodwaker1
@woodwaker1 6 ай бұрын
Chris, thanks for sharing this. Another great feature of Klipper, I have been using this for years on my Rat Rigs. It is really helpful when you have a 500mm square bed. I run this and bed mesh before every print. as the mesh can change when removing the magnetic bed plate. Many of the old printers did not have multiple Z motors that can be individually controlled, so this is not available for them.
@ChrisRiley
@ChrisRiley 6 ай бұрын
Thanks Dave, for sure, on the larger machines I wouldn't want to try and run without this feature these days.
@MakerViking
@MakerViking 6 ай бұрын
Good video Chris. :) Z-tilt is awesome.
@ChrisRiley
@ChrisRiley 6 ай бұрын
Thanks Thomas!
@tremrej65
@tremrej65 6 ай бұрын
Thanks Chris. I use z-tilt on an i3 printer (Geeetech) with dual z stepper and bl-touch. Klipper on that machine improved the print speed a lot, even at 12 volts.
@ChrisRiley
@ChrisRiley 6 ай бұрын
Awesome! Thanks for sharing
@dansteffee9759
@dansteffee9759 6 ай бұрын
I upgraded my Voron 2.4 to Tap , seems to do a great job. Doing away with the probe ... Great video !!!
@ChrisRiley
@ChrisRiley 6 ай бұрын
I'm glad Tap is working out for you, I'm going to check it out!
@kaseyboles30
@kaseyboles30 6 ай бұрын
ztilt also has implications for non-planar printing. With the right code and properly shaped hooted assembly one could do with a LOT less support material, much better bridging, and many other improvements.
@ChrisRiley
@ChrisRiley 6 ай бұрын
Ah, that is a great idea!
@enalecec5437
@enalecec5437 6 ай бұрын
Thanks Chris, for your explaination, i just realize that i set my z-tilt wrong. 😅
@ChrisRiley
@ChrisRiley 6 ай бұрын
You're welcome, I hope this helped!
@anand.s3843
@anand.s3843 6 ай бұрын
Hi chris, Can you please post a video on how to configure btt sfs v2 smart filament sensor on Octoprint? I configured with smart filament sensor plugin on Octoprint but filament not detecting. KZbinr dablet find alternate way by configuring it to Home assistant using MQTt, but her video is not clear. Please do a video on it!
@ChrisRiley
@ChrisRiley 6 ай бұрын
I will see what I can do!
@anand.s3843
@anand.s3843 6 ай бұрын
@@ChrisRiley Thank you!
@tytechguy
@tytechguy 6 ай бұрын
I run 3 VZBoTs so I don't need Ztilt but on my bed slinger I've been using it for years. It's a great feature to have. It also adds a button in the kipper interface within kipper screen which is also handy
@ChrisRiley
@ChrisRiley 6 ай бұрын
Very handy! Thanks for watching
@Karim3ds
@Karim3ds 3 ай бұрын
Greeting Everyone, Chris, thanks for the great videos, I'm trying to upgrade to the triple-Z adjustment, and I was curious about if I can perform such action with just Marline and no Klipper, since I haven't started with Klipper yet, I'm using a custom made printer and BTT Octopus, best regards
@ChrisRiley
@ChrisRiley 3 ай бұрын
Thanks for watching. Yes you can, I haven't done a video on how to do 3, but I have done one for 2, but you can use G34, search for that in the code to do multiple stepper motors.
@CaHeoMapMap
@CaHeoMapMap 3 ай бұрын
pro!
@ChrisRiley
@ChrisRiley Ай бұрын
😊
@MrHeHim
@MrHeHim 6 ай бұрын
Awesome! Basically auto tram Personally I like to run bed mesh to the temperature I print at most, or something in between. No matter how flat, the beds always seem to warp eventually and find a 'warped' home where it's stops warping anymore. Warp 😊
@ChrisRiley
@ChrisRiley 6 ай бұрын
Warp! Thanks for watching!
@ChrisFloof
@ChrisFloof 6 ай бұрын
Hi Chris! I noticed that your full steps per rotation explanation is wrong, unless you are adjusting microstepping through the stepper driver pins and not firmware. In Klipper, it's full steps for the motor without microstepping so a 0.9 degree stepper should have 400 steps specified there 😊
@ChrisRiley
@ChrisRiley 6 ай бұрын
Thanks!
@sleepib
@sleepib 6 ай бұрын
Can klipper(or any other firmware for that matter) use z tilt to allow mesh leveling to work with IDEX? So it keeps the two points you're printing above the same distance to the toolheads, and corrects x position based on z height and tilt angle. I can see this being useful for large beds.
@ChrisRiley
@ChrisRiley 6 ай бұрын
That's a great question, I am currently building an idex, we will see if we can make it work.
@samuelp1227
@samuelp1227 4 ай бұрын
I wish they had sensorless homing for each motor individually. It stops all 3 when 1 activates
@ChrisRiley
@ChrisRiley 4 ай бұрын
That would be an interesting setup. I might have to try it just to see what it does.
@samuelp1227
@samuelp1227 3 ай бұрын
It is possible in rep rap firmware. ​@@ChrisRiley
@ChrisRiley
@ChrisRiley Ай бұрын
@@samuelp1227 It would be tricky, but check this out. forum.duet3d.com/topic/30520/howto-configure-z-axis-sensorless-homing-in-homey-g-file/6
@MaddestGinger
@MaddestGinger 6 ай бұрын
I use it on a reconfigured mK3s… what is the difference with quad gantry leveling… qgl only for voron2.4 ?
@ChrisRiley
@ChrisRiley 6 ай бұрын
I'm not exactly sure, it could be something to do with how the belts and gantry work on the 2.4. Belts and flying carriage.
@MaddestGinger
@MaddestGinger 5 ай бұрын
@@ChrisRileyfound the info… z tilt is for 2 or 3 zMotor, QGL Is for flying gantry…
@sidbyron210
@sidbyron210 6 ай бұрын
I'm not sure of that my friend but even in high end machines mesh leveling it's a good idea, that's why in Voron 2.4 we have QGL.
@ChrisRiley
@ChrisRiley 6 ай бұрын
It's never a bad idea to run it.
@cristianopersi7953
@cristianopersi7953 6 ай бұрын
Chris can‘t find rhe link to the previous z video you mentionend.
@ChrisRiley
@ChrisRiley 6 ай бұрын
Here you go! Thanks for watching! Klipper - Z Endstop and Probe kzbin.info/www/bejne/h2PYc35rjd-Laqs
@RayLenses
@RayLenses 5 ай бұрын
How about bed slinger
@ChrisRiley
@ChrisRiley 5 ай бұрын
You can do a G34 or something similar if you have 2 different Z stepper drivers. kzbin.info/www/bejne/aZukd4SaidBrn9ksi=d6IMJQxkhVC_i7ne&t=777
@RayLenses
@RayLenses 5 ай бұрын
@@ChrisRiley I do have 2 different stepper drivers for Z axis but my steppers are TMC 2226, and im running klipper I’m not sure if this stepper drive has sensorless homing
@ChrisRiley
@ChrisRiley 5 ай бұрын
@@RayLenses 2226 does have sensorless homing.
@cantuchdis231
@cantuchdis231 6 ай бұрын
Chris could you please do a dual extruder single hotend klipper video.
@ChrisRiley
@ChrisRiley 6 ай бұрын
I'll look into it!
@RayLenses
@RayLenses 5 ай бұрын
I managed to do all configuration but the second extruder temperature is wrong because they're sharing same hotend i looked klipper documentation but couldn't find how to sync the temperature , so i stopped there 😢
@kyon_03
@kyon_03 6 ай бұрын
eddy coil installation please
@ChrisRiley
@ChrisRiley 6 ай бұрын
Working on it!
@jimmer411
@jimmer411 6 ай бұрын
Biggest improvement ive made is sourcing real mic6 from a local distributor. Now none of my printers need mesh.
@ChrisRiley
@ChrisRiley 6 ай бұрын
That's awesome! Thanks for watching
@rondlh20
@rondlh20 6 ай бұрын
In Marlin just run Gcode command G34 to do the same
@ChrisRiley
@ChrisRiley 6 ай бұрын
Yes, we have done videos on G34 in the past.
@hanslain9729
@hanslain9729 6 ай бұрын
Nice
@ChrisRiley
@ChrisRiley 6 ай бұрын
Thanks!
@Service_John
@Service_John 6 ай бұрын
1st!!😂
@ChrisRiley
@ChrisRiley 6 ай бұрын
😊👍
@scottsound4711
@scottsound4711 6 ай бұрын
Just Bambu it ..
@VincentGroenewold
@VincentGroenewold 6 ай бұрын
lol
@ChrisRiley
@ChrisRiley 6 ай бұрын
lol, Bambu is a verb now!
@Juiceboxmakes
@Juiceboxmakes 6 ай бұрын
Knowlage is power some of us like to have control under the hood
Sensorless Homing - Klipper - Chris's Basement - 2023
30:21
Chris Riley
Рет қаралды 27 М.
This over-engineered IKEA hack got out of hand!
25:40
Proper Printing
Рет қаралды 298 М.
요즘유행 찍는법
0:34
오마이비키 OMV
Рет қаралды 12 МЛН
Wednesday VS Enid: Who is The Best Mommy? #shorts
0:14
Troom Oki Toki
Рет қаралды 50 МЛН
Upgrading to Linear Rails a Waste of Money? - An Evidence Based Answer
28:34
Why All Bed Levelling Probes Suck - Eddy Modding and Testing
15:36
Input Shaper - Part 1 - Klipper  - Chris's Basement - 2023
29:32
Chris Riley
Рет қаралды 46 М.
Turn your Pico into a 400MHz 24 Channel Logic Analyser
25:26
Happy Little Diodes
Рет қаралды 72 М.
Why are we drying filament this way?
7:15
3D Printing Ideas
Рет қаралды 515 М.