Cimarron 1873 Single Action Revolvers Review

This is a review of a couple 1873 Colt replica revolvers made by two different Italian manufacturers and imported by Cimarron. I hope you find the information helpful, even if it puts you to sleep.
For those concerned with the hammer function as I was, this was the latest response from the Cimarron rep:
All Cimarron models are now designated “Frontier”. The Pietta models will begin with a “PP”’ The Uberti models will begin with an “MP” or a “CA”. All of the Pietta models have the four clicks. Only the “Old Model” frames made by Uberti have the four clicks. The “Pre-war” frames made by Uberti have a new firing pin safety hammer. These will only have two clicks. Uberti will eventually be installing this type of hammer on all single action handguns.

[@TUCOtheratt]

Ubertis are purdy, great for wall hangers and movie props. Piettas are shooters with much better actions, properly manufactured and hardened internal parts and perfectly timed actions. Uberti still anchors the ejection housing directly to the barrel instead of a lug last time I checked unlike Colt and Pietta and that's a part that will break sooner or later on Ubertis.

[@Sanguivore]

Didn’t expect to see you here, Tuco! Just watched your Pietta vs. Uberti video on lunch today, lol. You convinced me to follow my intuition and go with Pietta.

[@TUCOtheratt]

@@Sanguivore Hello there! Thanks for the nice response.

[@mikewilson5338]

The grips on the Pietta have a slight overlap called "proud." This is so when the wood shrinks the grips still fit.

[@jscott7635]

My first SA, and your video was outstanding in explaining some very important features. Thank you!

[@tucsonjack3991]

Best Cimarron comparison video on KZbin. Well researched and very informative. I believe the extra screw in the Uberti box is to replace the one that holds the cylinder rod in place, it fits flush to the frame. I currently own The Frontier 4 3/4" Old Silver Frame Pre-War Model, Laser Engraved with Checkered Walnut Grips in 45LC made by Pietta ( model PP410LSFW ) and am hoping to get the 1860 Richards Mason Conversion Type II in 45LC with the 8" barrel soon. Thanks again. Tucson Jack

[@kevins1114]

I recently bought one of the Pietta made versions of these. It's the "Pistolero" version, and it's nearly identical to the original Colt. I'm highly pleased with it.

[@Fredo_Bodybag95]

How does it function? I've been saving for a single action and the only one to really catch my eye is the pistolero in 45 lc. I've heard a lot of great things about it, but then again there aren't many videos for that specific model.

[@kevins1114]

@@Fredo_Bodybag95 Mine is in .357 Mag. It functions flawlessly, and is more accurate than I am. The action is smooth, and the trigger is excellent. The trigger pull weight on mine is about four pounds, and it "breaks" smoothly. One other thing about those clones of the first-generation Colts - you CAN safely have all six chambers loaded. When Mr. Colt designed that action, he included a safety feature. You simply pull the hammer back to the first "click" and leave it until ready to shoot. It will not "go off" by itself, even if dropped. I tried it. Generally, I found the fit and finish on these guns to be excellent, and the balance is really good. The recoil is a bit sharper with the shorter-barreled models like mine (4 1/2 inches) but it's not unpleasant. If you can get one, I'd call it a good investment.

[@Fredo_Bodybag95]

@@kevins1114 Thank you for the info brother, I appreciate it greatly, the one I'm looking to get is 4.75". Now all I need to look for next is a good holster 👍

[@SenkaBandit]

@@kevins1114please don’t use that first cock as a safety. It’s meant to catch the hammer if it accidentally falls from half cock. Despite what the old manuals say, don’t risk that notch being broken off by using it as a safety. Just load 5 and the hammer rest on an empty chamber

[@bubbleballs6200]

Absolutely best video I've seen on the subject. You should be proud in your ability to make an informative video.

[@miketaylor6700]

Great video, thanks. I’ve got the pre-war Pietta pistolero in .45 colt. I absolutely love it.. and actually had it in my hand while the video was playing.. as I followed all your explanation. Tough finding ammo for it during the past couple years. Sheesh. I think I’ll go grab another one chambered in .357 before they change the safety bar… thanks again.

[@shawnwood4317]

Very good review. You answered all my questions about the differences between Uberti and Pietta. Thanks

[@georgewashington9374]

yeah, totally agree, i wish uberti weren’t moving to the new hammer safety thank you for this video, good information, and after watching i think ill be going with the pp401 from pietta

[@thomasallen3818]

I have both Colt and Cimarron (Pietta) 4 3/4” SSA and the fit and finish on the Pietta made pistol is a notch above the 3rd Gen Colt. The walnut grips on my Cimarron fit perfectly and have beautiful graining. Both are chambered in .45 Colt.

[@ronrobertson59]

I agree Uberti is a better product than the 3rd generation Colts. I can but a pair of Uberti revolvers and if I add another $200.00 I can buy an 1873 Uberti Winchester rifle for the cost of one Colt SAA.

[@TheHitman-]

Both have cast parts also so na, I'll stick with my standard manufacturing, nickle 4.75 saa with the hand oil rubbed grips. 😊 Best built revolver there is. American anyway...

[@craiglewis6821]

Great history lesson! I have a clone with a 5.5 in a barrel in a .45 colt. I love it!

[@mrweeby1961]

Finally scratched that itch and picked up a few 1873 Colt clones. Two EMF/Piettas in 45Colt/45acp and a Stoeger Uberti in 357. They are very nice.

[@zatoichi124]

Really good review. Good points about the stainless. I think I prefer the Uberti in this comparison, but I don't want the floating pin safety either.

[@jerrysmith9315]

Very informative. Very good presentation Doc, Thanks

[@Arnfast66]

Great, thorough review of these revolvers and SAA generally. Great punch of information, not only of these two nice pieces. Thank you very much Sir!

[@bigwu100]

Best damn video on single action imported western style pistols i've seen to date. thank you information is power.

[@a1sloth1]

Yes, it is.

[@tucsonjack3991]

Good explanation between the Old and Pre-War Models. Thanks

[@carlwatson3220]

Thank you for this informative video, especially the "cylinder out of battery" part to keep the cylinder as pristine as possible. Mines a Cimarron/Uberti Model P .45 Colt 4 3/4, but only 3 "hammer clicks". Still love it!

[@kevinmalloy2180]

Wow, that was great. I am in the market, am not an expert (but love guns of the West) ,and it’s good to know that Uberti is a better quality gun.

[@spiritualawakenings6251]

Uberti and Pietta both make very fine replicas but so did Armi San Marco and Armi Jager I own all and have had no problems from any. In fact the Armi Jager I posses was manufactured in 1966 and was sold as the Dakota and as far as as color case hardening surpasses the Ubertis and Piettas. The newest I own is the Cimarron Wyatt Earp 10" 45LC and is a fine representation of a movie prop and 1st model Colt. I think what I am trying to say is after 40 years of collecting and shooting I can honestly say all the Italian makers have put out some fine replica firearms.

[@stevesharber634]

Just got a Cimmaron Model P. Beautiful gun! Nice video!

[@texasbassfreak3549]

Cimarron Frontier 1873 SAA Revolvers with 4.75" barrels are AWESOME in .45 Colt!!!

[@dudleylewis9142]

Chiapas firearm still

[@sunnycat69]

I like that they updated it with a safety inside the hammer itself let you carry a full 6 rounds and not have to worry about an ND like they did back in the day

[@TheMossbergg]

Excellent presentation !👍🏾

[@razorseal]

Very informative about PP and MP models. Now I know what to look for!

[@ronlafitte6864]

I would love to have several Cimarrons but if you can only shoot cowboy action ammo then count me out.

[@cimmeron.3576]

@@ronlafitte6864 I shoot full power .357 out of my .357 cattleman with zero issues.

[@ronlafitte6864]

@@cimmeron.3576 I’m sure the 357 is made solidly, but what about the 45 Colt? They are nice pistols but I sure wouldn’t want to damage one or blow it up, shooting full power 45 Colt loads.

[@cimmeron.3576]

@@ronlafitte6864 as to that I could not say personally. I read on forums that they are good with anything in Sammi specs. But like I said that is just from reading not personal experience.

[@ricktaylor5744]

Excellent video you did an excellent job on explaining these revolvers.

[@LAT-qk3vj]

Excellent review of both revolvers. Thank you for the cylinder tip. I'm in the market for one. Thank you.

[@cowboymusicstudio4911]

thanks on the info on the scratch on the cylinder i wondered what happened on my Uberti

[@brethawkins4151]

Excellent video. Helped me make my mind up. Appreciated.

[@jonasbrown7619]

Thank you very much. I am glad that it helped!

[@texan2560]

Best video yet on these guns!

[@BrianMcKinny]

Don't mean to be a pain with the PIE-etta comment, brother... it was just driving me nuts... I just wanted to say that your video has lots of excellent information in it, and it's very well done. So, cheers to that, and I've subscribed to be able to get notifications for more of your videos. :)

[@johncreed2627]

What a great opening picture, love those twins.

[@nealbeach4947]

Thank you for mentioning the first click as the safety. Samuel Colt was no idiot and designed a six shooter not a five shooter. He designed a way to keep the hammer off the cartridge and that was the first click. Thanks for a very informative video.

[@jonasbrown7619]

Thank you Neal!

[@BogeyTheBear]

Too bad it didn't work for long. The first sear kept breaking or wearing out and you're back to resting the pin directly against the primer cap. Five for the holster, six in the hand. You walk into what you know is going to be a ruckus, you slip in the sixth round and risk it. You load five if you're going to carry it in a holster for a time and pay no mind to it.

[@PaulSter]

I wouldn't trust that first click for anything in the way of a safety.

[@garylee9738]

Sam Colt designed it with a first click safety, but he wasn’t completely confident with it.

[@frosty0419]

Thank you! Perfect. I learned a lot about one I picked up today.

[@therealhawkeyeii7888]

The Cimarron Cattleman (SAA Clone) that I purchased in 1988 has a C prefix only. At the time, I was told that it was of Uberti manufacture, even though Cimarron is the only company marked on the gun.

[@sixshooter4570]

I love single action revolvers, and Uberti is a great manufacturer. I recently purchased a Standard Manufacturing 1873 5 ½" in .45 LC. Frame and hammer have beautiful bone charcoal hardened the old traditional way, and all the hardware, ejector rod, cylinder pin, trigger including screws are a light blued. The cylinder and barrel are deep, dark blued. It has a one-piece fancy American Walnut grips. All of the screws' slots are aligned with the direction of the bore, LOL! timed screws. I love this one, and it's a keeper!

[@jasonwotring6045]

Those Standard Manufacturing 1873's do seem real nice. I'd sure love to snag one up one day. My wallet however does not agree. Hahah

[@linguisticman]

​@@jasonwotring6045Same here. Would snag one in a second if I could manage to ignore my bills for a month.😊

[@jonathandavis9458]

The cylinder rod has a second notch. Push it to the second notch and it can't fire. It keeps the hammer in the first click position. Thats the safety

[@JAFO.]

My .45LC *4-Click "Evil Roy"* 4.75" comes with what I believe is a *Wolf brand* (lighter) spring, but I'd have to call Gene and ask to be certain. It's sure got a sweet trigger and hits where I aim it!

[@davevachon5025]

The Uberti model you have is the "new model sheriff". The screw holds the cylinder pin in place, they provided you with an extra screw. Where as the Pietta is the newer model that uses the spring loaded screw that you push sideways on to remove the cylinder pin.

[@repetitivemotion]

What beautiful revolvers you have there buddy! I gotta get me some

[@markd4741]

I once had the rare opportunity to buy a pair of two absolutely beautiful USFA Single Actions at a New Mexico Gun Show about 12 years ago. The seller that had these was from Las Cruces. They were absolutely magnificent, and would've surely appreciated. These were custom Shop issues, both .45cal, 5.5" Nickle Plate, smooth High Grade Walnut Grips, this identically matched pair had Consecutive Serial Numbers, and both had Dual Cylinders. Both Unfired, Unturned, Factory Cases/Boxes, all Paperwork, everything, the whole kit and kaboodle. Cash on the barrel, $2400 for the pair. I drooled for a 1/2 hour examining them both at them. and mostly without even touching them, they really blew my mind, and often regretted not snatching them. Maybe in a way it was good, it was a Sunday at that show I recall, and my Bank was closed! What sort of stopped me from buying them was the thought of then never firing them? A Safe Queen.

[@ridgehunter2217]

Solid video, informative. Thanks!

[@alexandernev24]

Thanks for the video....2nd time I've heard that about stainless vs nickle ..I was about to go nickle but you made a good point.

[@mariosanfilippo829]

M S The Pietta (All Second Generation) has a second notch on the Cylinder pin. By pushing the spring loaded button the pin con be set in this notch, therefore it will protrude from the back, stopping the hammer to go forward against the primer.

[@Wyld13kard47]

I got a pre-war model uberti that has the four clicks. I bought it around 5-6 years ago.

[@MrThedocholiday]

Very practical advice at the end regarding putting the cylinder back into battery before going from half cock to full cock, to prevent the bolt from scarring the cylinder. Thanks for that.

[@tpelle2]

Overall good video with a lot of good information. I would like to chime in with a couple of corrections. Regarding the frame design that used a screw to retain the cylinder base pin, this was the original style as adopted by the U.S. Army. However this only lasted for 8 or 9 years, then Colt introduced the spring-loaded cross bolt. I can only guess that this was due to complaints from the Army that soldiers were losing the little screws. (For some reason collectors call the first model frame the "black powder" frame, although this does not correlate at all to the introduction of smokeless powder.) Regarding the Uberti hammer that has the safety built in. Probably about 30 or more years ago I purchased a single action clone made by Uberti that also included a safety as you described. Beneath the firing pin on the hammer there was a little pivoting block that, when the trigger was fully pulled, it was rotated into a position that allowed the firing pin to hit the primer. In order to make this work it required a long thin hole to be drilled vertically through the hammer to accept a push rod that actuated by a lever on the trigger. The problem was that, to facilitate the drilling of this hole without snapping the drill bits off, the hammer was not hardened at all. Additionally the cam that operated the cylinder bolt that was made as part of the hammer dead soft too. The leg on the cylinder bolt promptly wore the cam down, and the cylinder bolt drug on the cylinder to the point that it eventually would not free the cylinder when cocking the hammer. This happened after only a few hundred rounds of ammo. This left a bad taste in my mouth for Uberti that has still not gone away. Later I did buy a Uberti-made Cimarron, and it has the 4-click firing pin on hammer action, and it has been a great gun so far. I also heard that Uberti is going to re-introduce the hammer-mounted safety dingus, and again has a hole drilled through the hammer to work it. No more Ubertis for me. BTW, I did just order a Pietta-made Great Western II revolver in .357 Magnum, and as far as I can tell from U-Tube videos, it has the original Colt style 4-click action and no transfer bar. Generally all of these imported revolvers incorporate the "Swissafe" which is the two-position base pin that can be set to block the hammer, as well as coil springs for the hand and for the loading gate. Both of these changes were to fix frequent breakage problems that occurred in Cowboy Action Shooting, which uses these revolvers hard.

[@tpelle2]

Corrections to my corrections: (I consulted my Kuhnhausen manual.) First, as to when the cross-bolt cylinder base pin was introduced, this was first used on a target model in 1892, nineteen years after the revolver was adopted by the Army. It was gradually phased in on all models in mid-1896. However there have been revolvers that, according to their serial numbers, were manufactured in 1899 still using the retaining screw. I still don't think this has anything to do with the availability of smokeless powder, but is just a coincidence. Logically thinking, a revolver firing black powder cartridges is going to require more thorough and frequent cleaning than one firing smokeless cartridges, so it would be less of a hassle to deal with the screw on the revolver firing smokeless powder cartridges. The remark that inferred that the coil spring for the cylinder gate was a "modern" innovation was a pure case of brain fade on my part. Most recently I had disassembled an 1860 Army percussion revolver that did not have the coil spring for the loading gate because, of course, a percussion revolver doesn't have a loading gate.

[@moonshinerphd9523]

I picked up my Taylor's & Co. Gunfighter the other day. It has a floating firing pin on it as well. I purchased a Uberti Cattleman hammer and trigger from Midwest Gun Works to replace the floating firing pin, which in turn will give it the four hammer clicks it's suppose to have. I wish these gun companies would leave well enough alone when they have a good thing going on, and stop trying to save their customers from themselves!.

[@Steve-hc7ix]

Very well done. Thank you

[@travis67]

Nice job on the video and info

[@leeburks4540]

I have two earlier Uberti Hombre models in .45. 4 click hammers, no safety feature, leave hammer on an empty chamber if carrying. I removed the cheap looking black finish, left them bare metal. The hand operates off a tiny spring behind the grip frame, the only difference from the Peacemaker I can see. Get a second hand Hombre at a pawn shop or gun show like I did.

[@davidmooney6733]

Amazing video just bought one today

[@tannstang]

Samuel Colt did not design the SAA or the four clicks...he had nothing to do with it...he died during the civil war...in 1862 if i remember correctly...the SAA was patented in 1872

[@jeffthebaptist3602]

Yes and the cap and ball guns only have three clicks because they don't have safety notches. They used the safety pin system instead.

[@jeffdunn7474]

Great video!

[@jonasbrown7619]

Thanks!

[@Mr.E-rg4tg]

Cimarron produces firearms within the industry of western reproduction arms. The firearms are manufactured to their specifications by Uberti and Davide Pedersoli in Brescia, Italy. Uberti makes their revolvers, lever action rifles as well as the 1885 single shot falling block rifle, and shotguns.

[@jamesosullivan1545]

Great summary

[@0ndrous]

11:36 Geez that sounds good. 17:57 16:13 I prefer the thicker beveled aesthetic of the Pietta grips.

[@titleistkoko]

Nice video, thanks

[@Brad-ic4bp]

Interesting - I always thought Pietta was just another importer of Unberti guns. I didn't realize Pietta was a separate manufacturer.

[@Atpost334]

That “extra screw” with the Uberti is the correct screw for holding the cylinder base pin in place since you have the ‘black powder frame’.

[@potlick18]

I have a Uberti. Really nice gun

[@nukeblue]

Super helpful video.

[@blackpowderfirearmenthusia3194]

Thank you I really like the Pietta oin the stainless steel

[@ChrisWilkesSurvival]

Great video

[@therealhawkeyeii7888]

I have a recently purchased (from Cimarron) Uberti 1873 revolver with a smokeless frame that has the same action as your black powder frame Uberti, i.e., four clicks and no firing pin block safety. Instead, like yours, it's equipped with a slightly over long cylinder pin that, when pushed all the way in, operates to block the hammer from falling all the way forward. This allows them to satisfy import requirements mandating some sort of safety device. Mine came with two cylinders: one in .45 Colt and one in .45 ACP, the latter of which is more economical to shoot, i.e., you can buy bulk packs from Walmart.

[@jasonwotring6045]

Lucky you. The Walmart where I live only sell shot gun and some rifle ammo. The only bullets they sell are .22 LR. But luckily we have. A couple gun shops in town. Nobody carries.45colt tho.

[@coaltrain4423]

Great video.I'm wanting the Uberti with 5.5 barrel from Cimerron.I'll try using the model number you gave to get the authentic 73 that you and everyone else prefers.That was a bad move on their sales strategy,producing something nobody wants.Go figure.

[@rojack79er]

I lucked out and was able to find a nice 5.5 inch Cimarron without the safety hammer safety. It only has three hammer clicks but man is it a beauty.

[@theykilledjoel1496]

What did u pay for it

[@rojack79er]

@@theykilledjoel1496 $670.00

[@Kau75]

Excellent presentation in helping me make my decision 😎🌺🌈🤙🏽

[@SamFugarino]

Taylors and Co. sale a conversion kit that allows you to swap out the trigger on the Uberti guns that lets you get rid of the floating trigger. This will give you back the four clicks.

[@bangsdagong]

great video maaan! thanks

[@sharonw2475]

I have a Pietta 1873 SA-FAP, Gen 2, with a 5 1/2 in barrel length, blue (looks black to me) finish with a brass trigger guard/back strap, the 2 piece hand grips appear to be some kind of rough textured brown hardwood or bakelite held on with a screw through the grips, the ejector button is oval shaped ,the serial number starts with an "E" 141xxx, it came with two cylinders, one for 45 long Colt and the 2nd cylinder is for 45 acp.

[@thomasallen3818]

Your Uberti pistol has the black powder frame. The Pietta has the “pre war” WWII, frame. I have a 1902 Colt 1873 in 44-40, and I had a Uberti and sold it. I have a Pietta 4 3/4” Cimarron Frontier model, and like it very much. Uberti I believe has caved to the Italian government safety regulations.

[@spiritualawakenings6251]

Carrying 6 safely is much better than 5. Personally when on the range I never count clicks when shooting, does it make them more accurate, less recoil, cheaper to shoot ? There are lots of clones out there and they are all good for the most part.

[@conradsenior5843]

That stainless steel gun is very nice. I wish I had one for target shooting.

[@swooshtx]

@ luftkrieger1943 Your thumbnail shows different grips; those are pretty nice where did you pick em up?

[@colteaton7877]

Good stuff

[@markhoffman3702]

“Pie-Etta”. I love it! 🤣

[@juliojames5986]

The hammer safety,as you refer too, does it have a effective utility ? All my SA revolvers have the Ruger design transfer bar safety, I have no problem with that, however I only load five. Thanks

[@mikebite229]

what also helps reduce cylinder wear is not spinning the cylinder as fast as you could that will also cause deep scratches on the cylinder and could also cause cylinder to be put out of time......

[@jimmyvalhalla1939]

The Pieta doesn’t use the s screw. The uberti is a black powder frame. It’s the base pin screw

[@quicktoevil]

I wish I had picked up a USFA Rodeo back when they were available. The plain satin black finishes coupled with premium craftsmenship just appealed to me. Reading the comments here suggests that most of theses Italian SA's need to be handled and inspected before purchasing. Nothing would disappoint me more than having an out of the box issue that requires sending the gun back.

[@kylewood8327]

Personally I like Uberti’s new firing pen safety, allows you to put 6 shells in the cylinder safely.

[@XXXChango]

Shells...

[@theseptembersessions_music]

Thank you! I seems that Pietta is the way to go then. Beautiful peices though

[@jstonePrototype]

What style and finish are the 2 guns on the screen when you click on the video

[@BertieW0oster]

You don't have to rotate the cylinder backwards before cocking to prevent wear. No matter where the cylinder is in rotation, when you take the hammer back to full cock the hand will catch it and rotate it into the right spot before the bolt drops. The wear marks come from people easing the hammer down without fully cocking it first, such as going from half cock to hammer down.

[@jakewayrewa5201]

I have the Uberti Cattleman II with the floating firing pin, and the 7th Cavalry 1873 "Old Frame". The old frame has the four clicks, but the cylinder pin is long. The Cattleman II has the short pin, so I switched them. The 7th Cavalry model is now just about perfect for authenticity, except the internal hand spring is a coil spring held in with a VERY TINY screw. Does the Pieta have a coil hand spring or the more authentic leaf spring?

[@theykilledjoel1496]

I just got a ubertie cattleman El patron and I love it

[@scottscheuerman6170]

Uberti hasn’t change the old model frame yet to the retractable firing pin as of 9/11/21

[@hamergalil1263]

Hello, do you think this armory would perform well in terms of defense and durability? What about the quality of these weapons compared to an 82 taurus? Thank you, waiting for a reply.

[@Physics072]

If you grab the firing pin of each of those revolvers do they have any slop/play? I've seen the Pietta Pistolero has a 4 click but the firing pin wiggles a little bit. Thought the original colts it was welded on no wiggle. Thanks! Which of the two do you prefer shooting? You said the triggers and hammers were a little different. Are they tight enough to allow fanning the hammers?

[@t.armstrong3119]

One of the best videos explaining modern Colt single actions. What made you get the 4.75" over 5.5"?

[@DigiDarkness]

Is the grips on the thumbnail real? If so, where can I purchase them? Sorry for commenting on an old video.

[@mauriceorayii2964]

The top one looks really close to the Colt Single Action Army I want to buy.

[@atlanticproducts]

Thanks for the review. I've only had one Pietta 1873, and that particular one had severe timing issues--much worse than your example. Should have sent it back, but it gave me a chance to flex my SAA gunsmithing skills. Turned out great, but it made me wary of Pietta. Shame, because Pietta is now the only Italian clone that retains the traditional lockwork. Also, Pietta is dimensionally closer to the original Colts than Uberti in the size of their frame window and cylinder. I REALLY like the looks of your Pietta! Those cylinder bevels are outstanding! And I'm glad that they haven't gone the way of Uberti as far as adding non-traditional safeties. I am, however, concerned about the timing on your particular example. It exhibits cylinder throw-by at kzbin.info/www/bejne/bnO3gHqDhbSVgqs, evidenced by your having to back the cylinder counter-clockwise after you cocked it fast in order for the bolt to lock into the cylinder. Were you to cock it that fast at the range, you'd probably have a misfire, due to the firing pin completely missing the primer. If, however, the firing pin still managed to contact the primer, you'd have lead spitting out the sides of the barrel-cylinder gap due to the cylinder's misalignment with the barrel at the moment of firing. Hard to diagnose from your video alone, but you do have a small problem. Not a big deal as long as you cock it more gently at the range. Just please be aware of your Pietta's tendency towards cylinder thow-by when cocking it hard and fast. Again, thanks for the review. Please don't take my comment as disparaging your revolvers. I get quite a few comments on my own channel that seem to serve no purpose other than to criticize the featured firearm.

[@Dr._Ghost]

Can these pistols handle smokeless and black powder rounds? I have a SAA from Cimarron, a 7" .45 Colt

[@theykilledjoel1496]

I bought a used one at a gun show guy didn't know what it was just said it was a ubeirtie and I can't see ubeirtie anywhere on it how do I tell what I have? looks exactly the same as the one on top with the bluing it's a single action has a small CS under the barrel

[@tonyfierro8642]

So the ubertti model is also unsafe to carry six does the firing pin rest on the primer?

[@forrestwebb8590]

You can get the black powder frame and you will have the 4 hammer clicks

[@shanemasters8370]

I have a Cimarron 1873 stainless steel 7 and 1/2 inch barrel it is a very accurate and awesome gun to play with the only problem I have is I can't hear the clicks they're very soft

[@tonyjr6841]

Only offering this because I had same issue. Don't know much about anything. Make sure all the screws are tight. Top, bottom, sides. It fixed mine right up and sounds beautiful. Just snug them. They don't need to be extremely tight.

[@tomsreviews238]

The stainless is beautiful.

[@hamergalil1263]

Hi, could you help me? I am about to buy an 1873 5.5, 357/38 and I would like to know briefly which one I should buy / which one is better, among them Cimarron, Traditions, Pietta and Uberti, which one would have more quality and would not give me any problems. Thank you, I await the reply.