In this video, we will walkthrough the VXLAN Multisite design and how it works!
Пікірлер: 28
@schadracpierre29257 ай бұрын
Thanks Rob! that's a very interesting videos with a lot of details.
@ipekposet86392 жыл бұрын
Hey rob, Thanks for the guides my man
@loud8665 Жыл бұрын
Rob thanks for sharing, helped me get a quick understanding of the some the DCI config differences. I have a build that is entirely eBGP based and the only benefit it that advertising the border gateways is the same as the other pairings . Wondering if you know any good resources for converged border leaves .
@mehdi-lp6kd3 жыл бұрын
Hi Rob, Anymore videos for VXLAN playlist? many thanks
@nds687Күн бұрын
Is this only for mac address propagation between sites or can it also be applicable to inter vxlan routing between datacenters ,so in other words l3vpn across sites. Also , if you're interconnecting 4 DCs, would this approach be sufficient? Or would it be better to go with interfabric option 3
@aliwaqas1643 күн бұрын
I followed your steps for Multisite Connectvity. I am receiving routes for vni 10010 on Leaf3 in AS65002 from AS65001. Also my BGW1 and BGW3 can see each other via ebgp and receiving all evpn routes but I can't ping from one site to the other. is there anything we have to do on DCI router.? Please assist.
@mohammedalsarrif924 Жыл бұрын
Well done thank you, kindly what can you do to reach PC in other site and other VLAN? using the same DCI link?
@marcelopolvora419811 ай бұрын
Hi Rob, I have two bgw in each site. Can I make the connection only between the remote sites or do I need to interconnect the bgw also within each site ?
@halfdone123 жыл бұрын
Thanks for this one Rob - Is there any VXLAN multisite configuration variant that would require the spines to act as VTEPs as well?
@RobRikerTechChannel3 жыл бұрын
You could, I don't believe it's a best practice but if you needed to setup a spine to terminate a VTEP, you could. To my knowledge, ACI multisite does exactly that. There's no Border Gateway in ACI multisite, to my knowledge. However, technically there's nothing stopping you from doing it. I don't know if it would work, never tested it out.
@noobsniperxx2 жыл бұрын
I noticed that you didn’t use any cast vtep in this video. I can’t seem to get it to work with any cast vtep. I’m going to try just normal VPC with vxlan and see if I can replicate this.
@arditriantoro78133 жыл бұрын
Hi Rob, is it possible to combine BGW under Spine. is there any reverence configuration for that because , I only find configuration multisite 3 tier desing BGW, SPINE, LEAF.
@RobRikerTechChannel3 жыл бұрын
There might be, but I followed the CVD for it. Config wise I would presume it to be similar to the BGW configuration. When I get some time, I'll lab it up and see if it's possible.
@khiz57552 жыл бұрын
Hey Rob Thanks for this video. In real world implementation do we use border gateways as separate devices connected to spines like other leafs or do we use border leafs as border gateways as well?
@RobRikerTechChannel2 жыл бұрын
You can do either, the BGW is a leaf terminating a DCI connection, you can use a converged leaf terminating external connections (border leaf), DCI (border gateway) and endpoints
@khiz57552 жыл бұрын
@@RobRikerTechChannel Thanks Rob Is it possible for you to share configs for border leafs. Also which nxos 9000v version you are using in this lab for border gateway
@khiz57552 жыл бұрын
hi rob another question does the vn segments need to match between vnis across dcs ? i understand multicast group doesnt need to match as between sites we use ingress replication?
@arturit0_ Жыл бұрын
@@khiz5755 Its the version 9.3.5 i guess, can someone confirm?
@aliwaqas1649 күн бұрын
@@arturit0_ the version is 9.2.2. it's in the very first video of the series.
@alexandresemenov86712 жыл бұрын
Hello Rob. I was trying to do multisite in pnet but have the problem with IR where arp is not working. If I configured static arp on both hosts the ping between them is working fine but without static arp ping is not working. I captured the arp traffic on fabric site interface on bgw but dont see this traffic replicated on dc site of BGW. The BGW is directly connected. Did you have this type of problem? What version of n9000v do you use?
@RobRikerTechChannel2 жыл бұрын
Interesting, I'm going back over vxlan again, more thoroughly this time, I'll see if I can replicate your issue. I'm using 9.2.2
@alexandresemenov86712 жыл бұрын
@@RobRikerTechChannel thanks Rob for your answer. I will try using 9.2.2 and check if the problem persist. Right now i was using 9.3.4 and 9.3.8 in bgw.
@khiz57552 жыл бұрын
@@alexandresemenov8671 mate do we need to match vn segments under vlans across dcs? also what about multicast groups..i dont think they need to match
@alexandresemenov86712 жыл бұрын
@@khiz5755 i think that it is important because the rewrite is based on RT what is based on VNI number so you have to configured same vni on both sides.
@zakariaelmantar4948 Жыл бұрын
Hi @alexandre i have the same issue with the same version that you use , did you try with another version ??