Clamping Tonnage Caluclation & The Steps

[@gtcollection6933]

Informative, as always. Thanks! good to see u in good shape man, keep'it up

[@injectionmoldingskillsmore1064]

Thanks for watching

[@NANI-534]

Thank you for Thais confirmations

[@injectionmoldingskillsmore1064]

Thanks for watching

[@himanshupanwar4330]

Thanks for sharing this.salute from India.

[@injectionmoldingskillsmore1064]

Thanks so much for the support & for watching the channel. Great things to come O YA !!!!!

[@TheMasterElite]

​ @Injection Molding Skills & More Hey neighbor! I'm in Greer. I just found your channel, this video has answered some questions I've had for awhile now. The parts I want to make are small but have a decent level of detail to them. Any openings in your no-doubt loaded schedule where we could meet for lunch or something?

[@injectionmoldingskillsmore1064]

I live in Destin Florida now bud. I work for the Southwire company. Thanks for watching & the support to the channel.

[@TheMasterElite]

@@injectionmoldingskillsmore1064 Aw, bummer. Well, if you're ever out this way, I'm buying.

[@kuharajmuniyandi2608]

Thank you for your video what is the difference in injection molding machine cushion and injection position

[@injectionmoldingskillsmore1064]

Cushion is the last little material in front of the screw. Injection position should be the same if you are looking at screw position. If you are looking at fill time is 1st stage till transfer then hold is next stage then the cushion would be 1/2 inch. to 1" inch on most parts. I hope this helps Thanks for watching.

[@kuharajmuniyandi2608]

@@injectionmoldingskillsmore1064 thank you

[@kamgangmei4075]

Sir could you please tell me why we use p.p material for purging?

[@Poetrap1]

If I want to do a tool transfer from one machine to the other with screw size of 32 to machine with screw size of 24 how do I calculate the shot size,changeover and speed? Thanks for great KZbins! I always watch your posts!

[@injectionmoldingskillsmore1064]

L/D rate is the only way to see the calculate size. Most of the time I start with the size off of the other press by taking it down by half. Then build it back up to 95 to 98% full shot. This is how I have been doing it for years, I hope this helps. Thanks for the support to the channel

[@mhc6148]

Can I know clamping force formula for split mould

[@injectionmoldingskillsmore1064]

Sure, I will show that in my next video on Friday. Thanks for watching & the support to the channel I greatly appreciate it.

[@mhc6148]

@@injectionmoldingskillsmore1064 thank you very much

[@injectionmoldingskillsmore1064]

You are welcome

[@ahmadallam9104]

How can i calculate projected area for the chair

[@injectionmoldingskillsmore1064]

Over all length by over all width & try to see what is the deepest area. Try that & see.

[@jeremymcclanahan2389]

What company are you with? I am with Infiltrator Water Technologies in Kentucky....I have enjoyed your videos.

[@injectionmoldingskillsmore1064]

I work for Ply Gem that's in South Carolina. They make siding, Gable vents, Shutters, & so on. Thanks for watching

[@selvam65koodalingam]

Thank you very much sir. What can I do if deep can increase above 2inch? Ex :8"

[@injectionmoldingskillsmore1064]

So for every 1" inch you increases by 10%

[@Alfred-gq3tl]

What if the part deep is less than 1"? Can we still use the same rule as 1" deep?

[@injectionmoldingskillsmore1064]

yes that is right

[@Alfred-gq3tl]

@@injectionmoldingskillsmore1064 What if the press has hot pot material feed into the sprue gate and to the parts and have 42 cavities? Do we need to calculate the sprue gate area and multiply number of cavities to determine the clamping force?

[@JohnSon-uq5jn]

If you don't mind sir tonnage formula tell me sir???

[@injectionmoldingskillsmore1064]

I think I have a video that shows it bud sorry very busy here at work. Thanks for the support

[@JohnSon-uq5jn]

I'm Indian 👦

[@injectionmoldingskillsmore1064]

Great bud