Clean HDMI output on older Canon DSLR Cameras Magic Lantern Video Guide including 5D 6D 7D and more.

[@HendrikEnsingMindLenses]

The way you showed a small step-by-step commentary was very helpful to me. Slow paced as I needed. Grateful.

[@illanbecker_Official]

Life saver. Can't thank you enough 🙏🙏🙏🙏🙏

[@pjsagnia]

You sir are a genius. You are probably the only one I've read or seen that shows how to do this practically. Thank you. Now I can use my Canon 5d mark ii as a 2nd camera for live streaming without that annoying white rectangle in view.

[@Voidpiercer]

Awesome Sauce. I got rid of my dang overlay - Thanks!

[@MargaretWacyk]

This was the most helpful video I found using ML after hours of searching. Thank you so much Phil for explaining it so well!

[@DarrenPauli]

Legendary, thanks mate. 6:38 for the settings to change

[@piotrscigalski2662]

Everyone was talking about pure hdmi, but no one showed how to do it. I have had ML for many years and that is my staple to make videos on eos 5d mark II. Until now, I could not use such a great camera for streaming. Hope that changes now. Thanks and greetings from Polish Krakow.

[@PLEDGE2WS777]

Did it work for you?

[@francoisd.9027]

Thanks, very clear and useful ! Brought to life my old Canon 600D

[@jcasbos]

Thank you Phil! This was very useful. Greetings from Mexico

[@WernerNoethe]

Just another great help. Now I can use my Canon 550D. Thank you very much.

[@nattewaditep]

What a great how-to! Thank you so much. I'll try that with my old Canon camera.

[@Obiektywni]

Amazing! Thank you Phil! Your movie was very helpful!

[@qbeatzqatar4973]

From my tests, for Rebel T5i, you should keep "Always" option on the overlays menu

[@NobleRenovation]

Hello, I have a T5i as well, were you successful in making the firmware switch to Magic Lantern? Any issues with video/zoom? thank you

[@Kronoen13]

Thank you so much for this! I picked up a T2i super cheap and was sad to realize it did not have clean HDMI OUT! This is amazing! SUBSCRIBED!!

[@thegamingrift6307]

hey did you manage to get a good setup with a t2i i have one and cant figure it out at all. im assuming you're streaming?

[@Kronoen13]

@@thegamingrift6307 Yes - You want to use the original SD card you got with the camera, that was the only factor I had issues with - Copying the files took a bit and I had to get an SD card reader for my computer but once I installed and loaded it and followed these instructions its been working fine. Once you set up the camera with the capture card you just have to crop to the image only as it shows the grey bars on top and bottom and side black bars. Once thats figured out the capture card has no issues. Would advice a $30 solution for overheating and a dummy battery. Hit me up on discord if you want to chat more! Kronen#1459

[@ghafarizainoorrohan8684]

usb capture can show 1080, eos webcam utility only 720p. this is really helpful

[@abdouunreal318]

thank you so much... I love the way you speak... I am french based in London and I wish to be able to speak English as good as you do

[@philbinks]

Merci Beaucoup!

[@zulfphotography]

Great job Philip nicely explained

[@treborikki]

Clear, concise, thank you for your tutorial and guide. This really helps.

[@nahumpena1152]

Excellent, Thanks

[@c3reachmiranda361]

So helpful! Thanks so much Phil

[@NoSQLKnowHow]

Very timely. I had just loaded up ML the other day and could not figure out what I was doing wrong. Cheers!

[@AnnaSmith-m4d]

THANK YOU SIR! simple clear and paced slowly enough for anyone to understand,. YOU ROCK!

[@HelpfulPhil]

Yes the ML website is back up and running. Thanks Alex !

[@floriankuddelgiese-music]

Great Job! Thank you so much!

[@Erindale]

Thanks so much! I've had an old 650D sat on a shelf for a few years. I see that streaming for extended periods with it could lead to damage but it seems a step up from an expensive paper weight! Appreciated!

[@HelpfulPhil]

Streaming this way is highly unlikely to damage your camera. I know of users who stream ’all day’ without concern.

[@Erindale]

@@HelpfulPhil That's great to hear thank you! My DC coupler just arrived so I will put it to the test!

[@FrankValchiria]

does it work with 5d mark III?

[@HelpfulPhil]

Have a look at the list of supported cameras in this video...

[@TerenceKearns]

This is great for picking up old gear on Marketplace and then using them with ATEM mini.

[@ACEPodcastNation]

Cheers @HelpfulPhil this helped me get over the final hurdle of removing focus rectangle. Should be good for using my cannon for live streams now once longer HDMi wire arrives. Happy New Year and best regards

[@ethanhaynesdrone9400]

Thank you so much, you are really Helpful Phil 😁

[@alecjohnson4070]

Thanks for a great video Phil! 🙏😂

[@bennyaus9308]

Than you Phil That was a very good lesson 😀

[@LoriWaters]

Very helpful! Thank you for this!

[@carlobeccegato2483]

Thanks! Very helpful

[@AladdinSoul]

Helpful video. I like it. Thank you.

[@pavelorlov9040]

Canon 200d please update

[@BboyGraphicx]

Thank you, this was brilliant

[@juancarlos3989]

I have a Canon 80D and I want to use it to take live videos, I connect the HDMI output to the capturer and from the capturer to the cell phone and only the video comes out, but the audio does not come out. As I do. -Does AUDIO come out via HDMI from the Canon 80D live? -When playing recorded videos if the audio is present. Thank you

[@beatprocess]

i put on clear overlay because i want everything off to use for podcast but im getting black bars on sides. i have the 7d

[@HelpfulPhil]

my other ML video could help kzbin.info/www/bejne/Zp_PaqJ7p7KgY8Usi=EndwZObfTwu5C_bh

[@OzBenamram]

That was helpful. Thank you.

[@v.crawford620]

Many thanks for your excellent teaching. I wish to add Magic Lantern to my Canon 6D but cannot find the older 1.1.6 version on Canon USA downloads. They only have 1.1.8 What do you recommend?

[@v.crawford620]

I should have watched further. I do see that Magic Lantern offers a link to the correct firmware.

[@Bordondental]

great video - thanks --- ill try it gladly

[@marzannegouws7524]

This was very helpful. Thanks Phil!

[@DavidOxford606]

Great information, Sir - thank you for posting. I have an old T5 and a T6 that have been boxed up for quite awhile, but was thinking of using them for some live streaming and video recording on to video capture/recorder. I followed your video instructions and was able to successfully install and use on the T5. However, for whatever the reasons (and the tech on this is way over my head), my T6 will not even recognize the ML firmware. I've searched the ML forum for info regarding the T6/1300D to no avail. Does anyone know of a build to support this camera - or if there is a work-around for it? At face value, I'm a little surprised at this since the two cameras are seemingly very similar. Thanks for any info you might have!

[@HelpfulPhil]

Sadly the T6 was never in development for Magic Lantern.

[@DavidOxford606]

@@HelpfulPhil that's a shame. Thanks for your reply!

[@bryanoz]

Very, Very Helpful Phil, I am coming back to the party with ML, I have to get up to speed this week to help a son out with a Zoom Meeting, we want to use my Canon 600d as a static camera facing people on the Board and another Canon 750D facing the speaker, mine is the 600d, quick question, as this is about 'Clean HDMI output on older Canon DSLR Cameras' excuse igronance please 🙃😛 What is missing from my model? Output wise, it has a HDMI out? is it in the resolution?

[@philbinks]

if you mean 'why use ML' then your camera will not have a clean feed, i.e. all the screen junk will stay in the picture. 600D resolution is not changed by ML - it is still low!

[@whatkindofblue17]

is there a version for canon 750d?

[@HelpfulPhil]

If it's not in the list then, No.

[@whatkindofblue17]

@ no luck then. Thanks though

[@Hassanalihassan89]

hi sir i have canon 70D , i turn off the power , but after 30 minuets its off . i don't want the camera come off . is there some thing to do it ?

[@HelpfulPhil]

Using ML live recording direct to a computer the camera should not shut off. In normal mode recording to the SD/CF Card they will automatically shut off at 29:59 (mm:ss). You can however select ML>Movie Tweaks>Movie Restart to restart automatically.

[@hey1inn]

Thank you very much!

[@LordIronFoot]

I have a Canon 4000D and I can clear the screen mostly but the final issue I have is the box that follows my face, I can't get rid of it. Any idea how?

[@bansdairy7175]

Can I use it in my canon EOS 350D

[@HelpfulPhil]

Only if it’s listed in the supported camera list.

[@ItsTooReal]

Sir I really need your help I’ve installed and taken off global but when I press the record button writing will appear on my screen

[@HelpfulPhil]

Unfortunately it's impossible to help everybody individually. The Global Draw setting is not the only one needed as you will see if you watch my video through to the end. Perhaps you need to set the Clear Overlays setting?

[@dbombd]

Can you make more videos on ML ,.. thanks

[@HelpfulPhil]

Yes, I think I will. Would you like to know anything in particular - Photo features; Movie features; Time Lapse ???

[@Neemooll]

Hi there. Just wanted to ask if there is a way to restore the original firmware if i ever wanted to get my camera to its original looks.

[@HelpfulPhil]

My comment in the video was misleading. ML doesn’t replace your firmware. You can use your camera as normal by not launching from your memory card.

[@Neemooll]

@@HelpfulPhil thank you for the answer! Very helpful video ❤

[@martinblackler1399]

Hi there. Thanks for these videos. I have a canon 60d and ive installed magic lantern and turned off global draw but that auto focus box is still there. Ive pressed 'set' (as per your other video) but it still remains. Any advice?

[@HelpfulPhil]

Other 60D owners seem to have problems so the settings may not work. Take a look through the comments to see if there is an answer. Good luck.

[@sinanarts]

thx dude.. saved me 500 bucks :-)

[@Calvarydima]

filming a conference . thank you , you helped. all though I still have vertical black borders and the camera would not stay over 30 min or so, all though its DC powered through a battery adaptor

[@HelpfulPhil]

assuming you were direct via USB or HDMI to a computer, the borders might only be removed by zooming at the PC software. Your camera shouldn’t cut off if you are only streaming to a computer. When recording video in-camera then you need to set ML - Movie: Movie Tweaks:Movie Restart > ON

[@Calvarydima]

@@HelpfulPhil actually you are right . I was using hdmi out and plugged into ATEM mini. I should have probably tweaked something to crop the source scene. Other wise I now understand I just need a different camera anyways . With a true clean hdmi. But it’s still something when u only have a canon ( mine is old 1200d but it still gives best smooth picture with best w/b even compared to semiprofessional 4K Panasonic video cameras that are used for additional sources ). Still best would be to have all the same cameras )))

[@uriscope6675]

Thank you so much, sir. your video is so precise and straight to the point. I can't wait to get my 5d mark 2 and get to work. #MuchRespect

[@NobleRenovation]

Once you drag the MT files to your formated SD card, do you extract the files before you place the SD card back in the camera? It's unclear where or when you extract the files...

[@HelpfulPhil]

expanding (extracting) is covered at 3m50s - before transferring to SD

[@NobleRenovation]

@@HelpfulPhil Thank you sir, I got the Magic Lantern software on, and did all your suggestions but for some reason, I have what seems more graphics on my HDMI video...there must be a setting I need to undo? ...many thanks

[@HelpfulPhil]

@@NobleRenovation check my Playlist for Canon, there might be an answer there.

[@priyonjoni]

Is there a way through Magic Lantern to keep the camera display on while there is a connection on the HDMI output? It's really annoying not having a way to monitor without an external display.

[@philbinks]

Yes! certainly on my Canon! I can just keep the LiveView screen on by pressing the LiveView button. In ML there is a Movie Tweaks Setting which says 'Force LiveView' you could try: 'Always'. Good luck

[@sky.172]

Anyone got it working on a canon rebel t3i?

[@topouzidd]

The output at Hdmi 16:9 t/b gives me an image on the proportions of the sensor, meaning that instead of filling the whole 16:9 panel with image, I’m getting black bars on top and right. The sensor proportions is 1920x1280. Is there a way to get rid of the side bars? If only we could select a picture mode of 16:9 aspect, it could fix this problem.

[@HelpfulPhil]

What camera are you using? Have you watched this related video...kzbin.info/www/bejne/Zp_PaqJ7p7KgY8U

[@topouzidd]

@@HelpfulPhil I’ve just watched this. As you said, the camera outputs 4:3 image just like the aspect of the sensor. I know about streaming software solution but I was hoping for a solution straight from the camera. My camera model is EOS 600D (or Revel T3i) which didn’t have support on Canon Webcam Utility 3 years ago, and doesn’t support on Webcam Utility 1 (canon Europe), nor in Webcam utility 2 (canon US, which by the way requires a subscription for more than 30fps or more than 720p on supported cameras). For some reason, on that video where you show the download page, I can clearly see that at some point the Rebel T3i was supported by the Webcam Utility, but it’s not listed there anymore!

[@bearpitrock]

Cheers Phil!

[@afgzayn2128]

Do you press record in camera or on your external recorder?

[@HelpfulPhil]

Press Record in your external software as you are taking in a clean feed from the Canon.

[@Kairod.ushindi]

Hey quick question, can you still use it for Livestreaming even after you installed magic lantern?

[@HelpfulPhil]

of course you can. That is what this video was about!

[@Kairod.ushindi]

@@HelpfulPhil thank you

[@mattcero1]

Awesome video man! Can you tell me if the 6D works well as a webcam using the Canon Webcam utility or by using an HDMI capture device? Any limitations? Thanks again sir.

[@philbinks]

With the 6D the resolution and lack of autofocus are a limitations versus modern cameras, but it's better than most built in Webcams.

[@mattcero1]

@@philbinks What resolution would you get using it as a webcam? I'd hope the 1080p. Thank you.

[@RacelifeCo]

Is it possible to get full screen out without the black bars?

[@HelpfulPhil]

see the video around 10:30 'clear overlays'

[@RacelifeCo]

@@HelpfulPhil thank you so much! Any way to get rid of the side bars also?

[@m1yth455]

@@RacelifeCo Did you ever figure this out?

[@RacelifeCo]

@@m1yth455 unfortunately no

[@kristiank3784]

Hey Phil do you maybe know how to get rid of the live view timeout while using the camera with hdmi cabel as a webcam?

[@Kiwisupremo]

what is intended here for "clean" ? without any black border?

[@philbinks]

Clean means no dialogue boxes. You can remove the black borders within Magic Lantern.

[@Kiwisupremo]

@@philbinks oh ok so it's a nice solucion.. btw i found a different solution within a stream software that allows you to "digitally" zoom the camera outout and remove the borders.

[@GhigginoAudiovisual]

@@philbinks how can i remove black edges on magic lantern? Thank's

[@HelpfulPhil]

@@GhigginoAudiovisual see the video around 10:30 'clear overlays'

[@LovesickAussieBoy]

Hi Phil,--I've set up my EOS M for streaming with Magic Lantern. I've bypassed the 30 minute limit, and it's all hooked up and I have clean output on HDMI through a video capture card, as you've done here. The image however is very low resolution, and looks really terrible, not at all like the lovely sharp image you get. My Logitech Brio produces a much better image, as does my Sony A5100, through the same capture card. Is it just that the Canon EOS M has lousy HDMI output? Or are there some settings I need to tweak?

[@HelpfulPhil]

Most likely that the output is 'lousy' as you put it. You can check the resolution by recording it directly on your computer and checking the size. If the resolution is reasonable you could look into creating a LUT (colour correction profile) for your recoring environment.

[@LovesickAussieBoy]

@@HelpfulPhil I think you're right. I just assumed that as the EOS M could do 4K raw recording it would surely output at least 1080P from the HDMI port, but not so! I now have my 6D set up through the same el cheapo capture card and the difference is day and night.

[@dablackguy830]

Will this work on a rebel 5 T6

[@HelpfulPhil]

T5 yes. T6 no.

[@dablackguy830]

@@HelpfulPhil ok thank you do any canons offer clean hdmi from factory? Or do you k ownof any dslr that do?

[@thatskimpossible9961]

Do we have magiclantern for eos 1500d/rebel t7.

[@HelpfulPhil]

Not on the list.

[@JSmith-ge2dz]

Any chance this fix works for a Power Shot G5X?

[@Bodonina]

No. Only the listed cameras

[@Lp-ze1tg]

14bit raw possible?

[@HelpfulPhil]

not when you're recording HDMI out. Check the ML site for in camera recording options.

[@jingwu997]

Great introduction! Subscribed. By the way, have you noticed that the CF card which installed the zip file, has to be in the camera all time when live streaming. And the camera won’t output a clean HDMI feeds if THE card is not inside. And according to the instructions, the basic level CF card should be 64GB. is there any alternative option, please?

[@HelpfulPhil]

The card with ML files needs to remain in the camera at all times for ML to operate. Follow your camera’s guide for card specifications.

[@PeterBestel]

Thanks Phil. It all worked except for the autofocus brackets on the 700D (T5i). Shame, as I need autofocus for streaming.

[@Bodonina]

That's right. Autofocus works only when you are recording directly to the camera's CF/SD card (offline). Streaming (online) with most ML supported cameras means you have to pre-focus and stay put!

[@mpasistasyalanci]

im currently looking to buy a used kiss x5, do you believe that the 600d/t3 version will work on that camera?

[@HelpfulPhil]

Yes. I don't know why there would be any difference - 600D/T3i by the way.

[@thegodfather4713]

Hi big bro. Is there a setting like cache clearing on Canon machines? my memory card is fast and powerful. And I formatted it, it's empty now, but the Memory Patches section in the Debug section is glowing red. It says the cache is not clean. how do i solve this problem?

[@HelpfulPhil]

I suggest you ignore it and get on with enjoying Magic Lantern on your Camera.

[@thegodfather4713]

@@HelpfulPhil Thank you, big bro

[@pauliesev6]

How do I get the Live View to stay on indefinitely? It always shuts off after a few minutes, cutting my HDMI out feed

[@HelpfulPhil]

checkout my latest ML video to see if that helps!

[@alexism2988]

Very thanks :)

[@israelalcaldetapia6068]

Thanks for the vid! Do you Know if i can use magiclantern for canon t6 (1300d)? Thank you!!

[@HelpfulPhil]

the only supported cameras are listed in the video.

[@jaycummins8296]

On the 6D the hdmi is only 720. Does ML actually output 1080 hdmi during live view or is it a zoomed version of the 720?

[@philbinks]

Many people get the Full HD (upsampled) resolution when connecting through software based broadcast software e.g. Ecamm Live. The natural video resolution for the 6D is 1728x1080px

[@jaycummins8296]

@@philbinks so using that in a multi-cam setup with the Atem mini, it will look different than the other 1080 cameras?

[@HelpfulPhil]

Try it to see if it suits your needs.

[@marcinsamotyja]

@@HelpfulPhil Is this me or magic lantern page is not working :( , does anyone have files for 6dMark II and can upload it to wetransfer or something

[@philbinks]

@@marcinsamotyja there is no ML support for the 6D Mkll. Looking into why the site is not working right now.

[@btmdc]

hello Phil, this is a real game changer for our livestream efforts, and thank you very much for your thorough, articulate presentation. A question: why do we need the 'top and bottom' shadows ? We are doing livestream, and do not want to see the lines at top and bottom.

[@HelpfulPhil]

btmdc you don’t need the guides other than if you want to see a guide of HD format ratio.

[@PlayMrGerman]

how to turn the autofocus off?

[@HelpfulPhil]

On the lens

[@PlayMrGerman]

@@HelpfulPhil sorry i mean the when its on :D like the focusbox. is it possible to turn it of cant use it as webcam with autofocus

[@Bodonina]

@@PlayMrGerman most of these cameras are not able to have Autofocus swith HDMI output.

[@Tim-Miller-]

Strange. I tried this with a 650D - followed instructions and double checked settings - even after connecting to video source and still see overlays. Bummer was looking for a cool way to bring HDMI into a Sling Studio.

[@HelpfulPhil]

Hi Tim, try this video as a follow up kzbin.info/www/bejne/Zp_PaqJ7p7KgY8U

[@CadeBrazil]

Awesome!!! 2021

[@sebastian7055]

Hello, is there a way to conect my canon EOS 7D into a black magic Atem Mini? it shows a blackscreen, I supose is because is not a clean HDMI output from my camara, does this software u show can help me with this issue?

[@philbinks]

You need to work out your problem with the Atem. ML won’t help but does provide clean HDMI.

[@sabrinamills17]

I have a 7d and it works with the ATEM Mini! Trouble shoot your cable and make sure your ATEM is set up correctly. It also used the auto focus. Good luck to you!

[@0oTHEJACKo0]

I use the 5dMarkiii with it, but it is not really clear hdmi out. It still shows the record button, and also is a bit squished, despite choosing 16:9 t/b of course etc. any ideas? :)

[@HelpfulPhil]

I don't know why it shows a Record button ??..you could try a different Aspect ratio e.g. 16:9 bottom, under, but I don't think it will make a difference.

[@0oTHEJACKo0]

Tried all of it. Doesn't change. Also tried with clearing the overlays with ML, that worked, but it is still squashed. Mhhh

[@HelpfulPhil]

@@0oTHEJACKo0 what happens if you choose 3x2 ratio ? does that allow you to 'enlarge/crop' in your receiving app.

[@0oTHEJACKo0]

@@HelpfulPhil same unfortunately.

[@HelpfulPhil]

@@0oTHEJACKo0 What HDMI capture card are you using...also 5Dlll is supported by Canon webcam Utility via USB

[@StellarAudyssey]

ML does *not* replace your camera's firmware. You can format the SD card just fine at anytime, as the ML files will be automatically loaded back to the SD card after formatting.

[@HelpfulPhil]

When you elect to Format the memory card in your camera, you are given the option of retaining the required ML files, or also deleting them. Deleting them means that your camera will revert to using the installed Canon Firmware.

[@StellarAudyssey]

@@HelpfulPhil Yeh like I said, SD Cards can be formatted just fine in the camera, unlike what you said in the video. ML does not replace the camera's firmware *at all*. ML loads off the SD card, after the camera boots with the Canon firmware. No, there is no "reverting back" to the Canon firmware. It is always present in the camera's rom, as it's fundamental to the functioning of the Camera. Basic points of misinformation in your video and in your comment above... Otherwise, it's a relatively helpful video.

[@topouzidd]

@@StellarAudyssey(I’m 2 years late to this conversation but…) you are wrong and the video is right. Magic Lantern modifies your camera’s firmware so that it can read and boot from the card. And if there is no magic lantern on the card, then it doesn’t load the magic lantern extras, but your camera’s firmware will still be modified. You have to remove magic lantern using the menu to be able to return to stock firmware. It’s not a good idea to format your SD without having a backup of your stock firmware.

[@GaityMan]

hi! What am I doing wrong? I put up 16/9 or 16/10 but my canon 60d broadcasts the image in 4/3 format , more precisely, the black bars on the left and right. I thought that there would be a problem with the upper and lower bands, but it turned out to be the opposite. can you help me? Hello from Russia)))

[@philbinks]

Hi GR, not really as the camera format is 4x3, so depends on what software you are recording/streaming with as that is where you will set your 16:9 format. See my other video if it helps kzbin.info/www/bejne/Zp_PaqJ7p7KgY8U

[@christiaanstoop1537]

Thank you my 600D HDMI is clean but the shutter close after 30sec.

[@HelpfulPhil]

That might be down to your HDMI cable or USB connection. Check the USB bus on your computer to see if the camera is seen. Also make sure your camera is fully powered.

[@christiaanstoop1537]

And just after I left this comment I got it to work. Thank you so much it works 100%

[@pepepemariano]

Hi, i have 600d as well and i will give this a try. Is the hdmi output full hd? i guess in this camera is lower resolution, but just asking. thanks

[@HelpfulPhil]

@@pepepemariano it depends on the connected software features. It may up sample the signal to HD 1920x1080 by interpolation.

[@leedobson8031]

Very nice! It was easy to understand and the walk-through was very helpful. Does your camera switch itself off after 30 minutes or so?

[@philbinks]

No, this should not happen if it is connected via either USB or HDMI. You must not be recording to the internal SD/CF card. There is a ML setting anyway:- Movie: Movie Tweaks: Auto Restart - ON

[@leedobson8031]

@@philbinks Thanks for the reply and the useful advice.

[@gabrielmpenteado]

Thankssss

[@kenny6105]

I've spent all day fighting with my Canon Rebel T6 trying to get clean HDMI, my heart sank when I saw it wasn't on the list. oh well, time to keep looking

[@HelpfulPhil]

Canon EOS Webcam Utility is your answer.

[@atticusnari]

Sad, no 6D Mark II

[@philbinks]

no need as most ML features are built in by Canon for that model.

[@atticusnari]

@@philbinks There is no Clean HDMI on it

[@philbinks]

@@atticusnari try www.usa.canon.com/internet/portal/us/home/support/self-help-center/eos-webcam-utility/

[@donaldphotovideo]

Subscribed :)

[@masterchririus]

*It doesn't replace the firmware, it coexists.

[@HelpfulPhil]

Turn off Auto Focus and on your lens the same. Focus tracking is unlikely to work, depending upon Camera model, with ML's clean HDMI output settings.

[@CatHarington]

doesn't work on 600d/T3i. This is not a clean hdmi out. Its simply hiding the overlays.nothing more. the resolution is still the same as the Display. And i have a black frame on every side. For streaming its useless

[@HelpfulPhil]

You might have the settings incorrectly set ? look at Display > Advanced Settings > Screen Layout.

[@CatHarington]

@@HelpfulPhil I changed that. But the t3i doesn't fill the screen.

[@fotokunstlindsaycom]

Hi program all good, but on my Canon 50D is still any help?

[@HelpfulPhil]

Canon 50D is listed on the supported cameras list in the description