I did not know how to read and write an EEPROM 5P08C3. Thanks to you I know now that the EEPROM programmer X-prog M 5.55 can do this and you have to use the setting ST - ST95P08. Thanks a lot!
@LMAutoRepairs Жыл бұрын
X-prog should reap that chip indeed... Yes, use 95080 to read that eeprom... 👍👍👍
@miroslavmiljkovic1665 жыл бұрын
Thank you for this video. In my case, I can not copy chips, I do not have the equipment/programmer. But, I will swap them, since my ECU won't start vehicle. I am getting used working ECU and replace this chip, and hopefully, car will start. I will post here the results in a few days, for anyone interested to see.
@LMAutoRepairs5 жыл бұрын
👍 Thank you for watching!
@djokakatastrofa77364 жыл бұрын
Have you started the car?
@miroslavmiljkovic1664 жыл бұрын
@@djokakatastrofa7736 I swapped 5p08c3, I was told it is immo chip, and AM29F400. It is car CMOS, and I was told to swap that also. Unfortunately, car displayed same errors, won´t start. Needs to be checked by specialist.
@djokakatastrofa77364 жыл бұрын
@@miroslavmiljkovic166 Have you fixed the car? So you were told that both 5p08c3 and AM29F400 contain immo data? Btw what does the CMOS mean? Maybe you have faulty eeprom, do you have any kind of eeprom reader to check for data? Best regards from Prijepolje, Serbia...
@miroslavmiljkovic1664 жыл бұрын
@@djokakatastrofa7736 Sadly, it is out of my hands now. Car belongs to a friend, and was towed to some specialist. When I get any info I will post it here.
@ruimiguel69697 жыл бұрын
Please continue this sharing. We the electronics guys just love it :)
@LMAutoRepairs7 жыл бұрын
Rui Miguel No worries... thank you for your comment!
@omarjuma13695 жыл бұрын
I'm need more introduction to make chip and mobilize
@larryhurst89587 жыл бұрын
I had a Lexus IS300 in shop for bad gas gauge and blinking low fuel light. Scan codes, nothing in ECM except P0420 and P0430, replace cats fixed that problem. Could not communicate with BCM. Pulled tank unit(easy) and the sender was ok. Boss said put a cluster in it. I decided to pull BCM, and it had corroded areas on the board. I cleaned the corrosion and reinstalled and it worked. How long, who knows. Called around, dealer, etc for new BCM. Remans were $325 and had to be programmed on car by dealer. New from dealer $550 and same programming issues. We cannot program in our shop. No equipment. I bet you could have figured this one out. Would have been an interesting case study.
@andrewuhioh5 жыл бұрын
This is beautiful. You are one kind of a tech guy I can't but watch. You are a blessing to auto Technicians🤘🏿I have a question, When you copy from the require immobilized ECU to the known good one, do you delete the program from the one you are coping to before you write the required Imm program to it? Thanks
@LMAutoRepairs5 жыл бұрын
Not necessary... unless is a eeprom that requires erase before writing... most don't need to... Thank you for watching and for your comment!
@gerigesquiere665 жыл бұрын
To read the EEPROM on the board connect a condensator parallel to the piëzo oscillator. The processor stops and you can read the EEPROM without desoldering. I never done that but I read this somewere on the internet. I have stops with DPF and EGR Off in 2014. Will yoou try this the next time? I'm cutious. At my age (72) it's very difficult to work on ECU's. My eyes aren't good enough. Thnaks for video.
@LMAutoRepairs5 жыл бұрын
Loads of eeproms, you don't even need to do that... For me however, it is just easy to remove it... Thank you for watching and for your comment!
@RinorBislimi5 жыл бұрын
I have 3 questions. 1. If we make all bytes 0 to EEPROM will immo be off? 2. Will central lock works after immo off? 3. Best way to find EEPROM chip where is located in ECU or IMMO box? Thanks a lot keep it up 👐
@LMAutoRepairs5 жыл бұрын
Hi 1. No. 2. Yes. 3. Each module has an eeprom or more, that contains info needed for the modules to work correctly... Hope that helps. Thank you for watching and for your comment.
@AIRCon2507 жыл бұрын
This channel is awesome, thanks sharing it for free !
@LMAutoRepairs7 жыл бұрын
Daniel Fetca Thank you for your comment!
@ELEISONCARABALLO4 жыл бұрын
Very good video Luis, please tell us what software you recommend to do this job and virginize ECUs and how to recognize what chip is needed to read and why. KInd regards from Slovenija
@MarcoPereiraFerramenta-Online4 жыл бұрын
Muito bom o vídeo obrigado pela partilha . Eu tive aqui um ECU dessas com avaria e tentei só trocar a Eeprom 5P08C3 da ECU com defeito para uma outra usada e o carro não trabalha na mesma .
@LMAutoRepairs4 жыл бұрын
Provavelmente o problema não é da ecu... A ecu usada, era de um carro igual? 👍👍👍
@MarcoPereiraFerramenta-Online4 жыл бұрын
@@LMAutoRepairs Sim de um caro igual, mesma referencia tudo igual, estive a ver e parece que as ECU de três fichas não dá só para mudar a Eeprom , tem de se faz Flash a AM29F400BT .
@LMAutoRepairs4 жыл бұрын
@@MarcoPereiraFerramenta-Online Sim... em algumas o imobilisador está na flash...
@MrLipp247 жыл бұрын
Let us know, if the repairer guessed right with the original ecu holding the injectors open. Cheers for the video mate
@LMAutoRepairs7 жыл бұрын
MrLipp24 I will...
@LMAutoRepairs7 жыл бұрын
MrLipp24 Unfortunately the problem was not the ECU... I am not though if he got to bottom of the problem... if I know anything I will post it here...
@yassinekeziwa44297 жыл бұрын
Hello you are working a great job here, I always support you
@LMAutoRepairs7 жыл бұрын
yassine keziwa Thank you for that!
@MaicSalazarDiagnostics6 жыл бұрын
Very good info, please next time show the de-soldering and soldering techniques
@LMAutoRepairs6 жыл бұрын
Maic Salazar Diagnostics Hi Stay tuned... there is a video coming for that... or check my Patreon page... Thank you for watching!
@Dogpool4 жыл бұрын
How is one supposed to know what chip is the right one? I have a 2011 Subaru Forester I’m trying to swap out, but can’t find a ecu diagram
@LMAutoRepairs4 жыл бұрын
The chips usually have numbers written on them, that will help you identify them... Thank you for watching!
@ds.4765 Жыл бұрын
Thank you very much for doing this tutorial video on how to clone an eeprom , I'm in the process of doing the exact same thing I live in Denver Colorado United States can you tell me where do I need to take my two ECU'S so they can do this procedure you just did , can a computer repair shop do this? Please reply thank you and God bless
@LMAutoRepairs Жыл бұрын
A computer shop should be able to do it... Just ask them... 👍👍👍
@mickymadueno65944 жыл бұрын
good job so when we clone an ecu basically because they remove the memory from the original ecu and weld it to the ecu that we are going to replace and then I have seen that you have to basically copy that data and thanks for your videos I am from Peru but I live and work in Spain
@LMAutoRepairs4 жыл бұрын
👍👍👍
@quynguyenduy24617 жыл бұрын
it very useful for me and everybody on the world. thanks you so much
@LMAutoRepairs7 жыл бұрын
+Quý Nguyễn duy Thank you for watching and for your comment!
@estrikadev95544 жыл бұрын
luis eu nao sei se alguma vez exprimentas te desta forma a soldar ics. em vez de limpares os pads de solda passas so o ferro pra nivelar a solda dos pads depois colocas o chip o mais proximo possivel, normalmente ele ficara um pouco torto ao lado dos pads colocas bom fluz e das lhe ar quente quando a solda esta no ponto das lhe um toquesinho pro sitio, muitas vezes a propria solda puxa o ic pro sitio correto. eu antes limpava pads mas deixei de fazer isso quando comecei a arranjar telemoveis e notebooks torna se mais facil pra mim desta forma
@LMAutoRepairs4 жыл бұрын
Sim... ICs pequenos as vezes também uso essa técnica... mas em chips mais é mais complicado... Obrigado pelo comentário! 👍👍👍
@rtt9319795 жыл бұрын
I have a Kia Rio 2009 JB and we replace old ecu and put used donor ecu. Question is where is the chip that i need to swap in order to make run the engine. I'd like to upload the photo of the ecu but i don't know how to upload here
@LMAutoRepairs5 жыл бұрын
You can't upload here... there is always www.patreon.com/LMAutoRepairs But you need to transfer either the eprom, if external, or the data from the MCU eprom... Thank you for watching and for your comment!
@maheromar86883 жыл бұрын
Is it posiible just to read the date from the old ecu you and write it on the new ecu without removing it?
@dandwrasan23425 жыл бұрын
This is a fantastic vid and I understand your English perfectly 👍🏻
@LMAutoRepairs5 жыл бұрын
Thank you! For watching and for your comment! 👍👍👍
@dandwrasan23425 жыл бұрын
Your welcome sir , I have a question about ecu and the immobiliser do you have a email address please
@LMAutoRepairs5 жыл бұрын
@@dandwrasan2342 Hi Ask here... or check my Patreon... 😉
@DiyMech7 жыл бұрын
Superb video, so why do you need to remove the chip to download it's contents, cant you figure out a socket clamp to go over the device pins in situ ? or am I missing something, would be a lot easier ???, then you could clip other device and upload other chips data ???
@LMAutoRepairs7 жыл бұрын
DiyMech Hi You are absolutely correctly... The only thing is that some programmers, and/or some boards layout do not allow to read the chip while on the PCB... the best safe way is remove the chip... consider to read in circuit (while on the pcb), MCUs or big chips... for a 4 pin chip, safest way is removing... but hey, this is just my opinion and the way I do it... Hope that helps... Thank you for you for watching and for your comment!
@alitehrani34153 жыл бұрын
Great video Can you tell me in any car ecu how do I locate eeprome if there are more than one ? Is there any publication that shows location of eeprome on different ecu or do they have any special numbers that we can recognize them ??
@michaelbuck62653 жыл бұрын
Great question, I to0 am also curious how to find which 8 tipped eeprom on the motherboard inside the pcm
@LMAutoRepairs3 жыл бұрын
Read their id stamped on the chip... It is that simple... 👍👍👍
@michaelbuck62653 жыл бұрын
@@LMAutoRepairs that simple than explain cause not being as smart as you or a mechanic I don't know what I. Looking at andy 07. Passat has 4 ( pinned ones looking the same, what number do I look for?
@LMAutoRepairs3 жыл бұрын
Again, look at what is written on the chips... obviously I know some of them and I can easily identify them by that... But you can easily Google it, and quickly find what a certain chip is... 👍👍👍
@michaelbuck62653 жыл бұрын
@@LMAutoRepairs I'm not following the little ones have numbers and I Google it and find nothing
@johnmoran48914 жыл бұрын
Great presentation. If one removes the chip will the RCU run normally without testing for key?
@LMAutoRepairs4 жыл бұрын
No... The contains other important information, the ecu will not run without it... Thank you for watching!
@wicked_garry4 жыл бұрын
without cheksum will be error enable like OSM checksum or eeprom checkcsum error
@mariobenetti24224 жыл бұрын
ok, i try to do it, and after i told you what- virginize with - carprog? iprog+ ? upa usb?
@ssgssg19084 жыл бұрын
Great job that's good
@LMAutoRepairs4 жыл бұрын
Thanks! 👍👍👍
@sonsofliberty906 жыл бұрын
Amazing video!! The best i've run across until now!! Thank you!!
@LMAutoRepairs6 жыл бұрын
Thank you so much! Really appreciated!
@tonderai2634 жыл бұрын
Original ECU was stolen from vehicle so I cannot clone the immobiliser , I have a obtained a replacement one , how do I go about it ?
@LMAutoRepairs4 жыл бұрын
You yo either immo off, or virginize and reprogram to the car... Thank you for watching!
@bgfrdqf447 жыл бұрын
Thank you for all your videos tones of informations 👍👍👍
@LMAutoRepairs7 жыл бұрын
Noureddine benguermit Thank you for watching and for your comment!
@Peter-fckyt5 жыл бұрын
Hi, thanks for the video to start with. My idea is to have a clone of mu ECU as I will attempt to remap it myself. I have bosch EDC15c2 with 5P08C3 (identical as per video). Following your guidance and using blank soic8 eeprom, would it make sense if I read my with soic8 with clamp (no desoldering needed) and saved the .bin dump and then uploaded it to new eeprom (or erase and write to the existing one, that will mean I would have 2 identical IMMO coeded ECU's?
@wilbertoaguilar79024 жыл бұрын
how do i know wich chip to replace on a 2008 audi a8 (immobilizer)
@mohammadumushakir3262 жыл бұрын
Hi Luis, How to know the location of the immo eeprom? I just started to learn the eeprom need to know some tricks Thanks
@LMAutoRepairs2 жыл бұрын
There is some variations... some ecus actually have the immo stored in the flash memory... You need to know what you are dealing with before do anything... 👍👍👍
@mohammadumushakir3262 жыл бұрын
@@LMAutoRepairs Thank you so much appriciate it
@toms21014 жыл бұрын
Wow,you are amazing,thanks for posting !
@LMAutoRepairs4 жыл бұрын
No worries... Thank you for watching! 👍👍👍
@vwstauvros6 жыл бұрын
hi there i have a citroen saxo 1100 8v model of 2002 the car stay a long time with out battary and now when i try to start the car dosan't starts and the light of immo is on ,i have to reprogramming the ecu but i wont to bypass them.Did you have any idea who to bypass the immo,THANK YOU
@LMAutoRepairs6 жыл бұрын
Hi You need to see which ecu is fitted on that... But, but you scanned the car? It might be something simple and easy to fix.... Thank you for watching!
@michaelali49032 жыл бұрын
very good job
@LMAutoRepairs2 жыл бұрын
Thanks! 👍👍👍
@hbenred13847 жыл бұрын
thanks lot i like your videos they are very clear
@AutoOtwieracz6 жыл бұрын
Hi, i have a 807 with edc15c2 2.0hdi and reprogram eeprom an am29f400 with no immo bin files. Car does not start yet, should i reprogram BSI? Please HELP! Thank you!
@LMAutoRepairs6 жыл бұрын
De Ce Hi Where did you get the eeprom file from? Thank you for watching!
@AutoOtwieracz6 жыл бұрын
I’ve read and used a program to remove ImmoServiceTool. I lost my original eeprom files that why i need immo off.
@LMAutoRepairs6 жыл бұрын
Hope you have learned the lesson of the importance of make backups before do anything with the files... lol I do have an original dump and an immo off dump from that ecu, although was from a 2.0 206...
@AutoOtwieracz6 жыл бұрын
LM Auto Repairs please write to me an tob.matlab@gmail.com , yes i know thats is important to make a backup, but i am not sure it is good readed, because i have a problem with my tl866 and 5p08 eeprom, thank you for your response, you make a great vidios,
@LMAutoRepairs6 жыл бұрын
I think you first need to get a good programmer...
@dannychilembo5166 жыл бұрын
My vw polo 1.4 can not start after connecting the battery backwards. At first it brow the fuse after doing a wrong battery connection. Then I bridged the fuse thereafter it was again wrong connection of the battery. This time it can start.what could the problem
@LMAutoRepairs6 жыл бұрын
Danny Chilembo Hi So, you bridged the a fuse, and then you connected the battery backwards again!? Try to scan the car, and see which modules you can't connect with... check all fuses etc... do not bridge them... replace it! Thank you for watching!
@RayonsAutoDiagnostics5 жыл бұрын
How do you identify which eprom is for the immobilizer?
@LMAutoRepairs5 жыл бұрын
There is only 1 eeprom... so you can't really get it wrong... Thank you for watching and for your comment!
@rk18drive134 жыл бұрын
whats the conditions or rules to copy the full data from one ECU to another. what is the ECU are not same cods? as i am the new learner i have learned a lot through your great videos thank you.
@jeffsylvester52795 жыл бұрын
Hi, Luis, great video. Do this chip contain the injector codes that are printed on the injectors because i recall once you change ecu it has to be programmed to the replaced ecu otherwise it wont start
@LMAutoRepairs5 жыл бұрын
Hi It depends... some cars don't even need the injector codes... Others will start but might trigger the engine light... every maker is slightly different... But, some ecus will have them on the eprom, and some on the flash... You need to know which ecu you are working with... Thank you for watching and for your comment!
@jeffsylvester52795 жыл бұрын
@@LMAutoRepairs hi. Ok i have a citroen c3 hdi 2002 model , i bought a lockset , can the eprom from bad ecu be swop with the one i bought.thanks again , great stuff
@Rwecosher2 жыл бұрын
Is it possible to read the data from the immobiliser nit itself and copy that to an ecu?
@LMAutoRepairs2 жыл бұрын
Not really... It does not work like that... 👍👍👍
@lukephil63843 жыл бұрын
Why you had not tried to read through ic clamp instead desoldering?
@LMAutoRepairs3 жыл бұрын
🤷♂️ LOL It is so easy to remove this small chips, that I prefer to just desolder... Thank you for watching!
@lukephil63843 жыл бұрын
@@LMAutoRepairs i asked that because is simple to desolder as most simplest to not desoldering it, just r/w via IC clamp placed on it. Thats it!
@LMAutoRepairs3 жыл бұрын
Yes, but some chips the circuit on the board can prevent the reading or writing, or even corrupt the data... Does not worth the risk... my opinion...
@VisarLimani4 жыл бұрын
Profi Tuto. Thanks!
@LMAutoRepairs4 жыл бұрын
👍👍👍 Thanks!
@menel5982 жыл бұрын
I want fish and chips now.
@alevogod4 жыл бұрын
I have 2006 Suzuki grand Vitara with no working keys. Recently I swapped the ignition and also PCM with a set of key from another Car. Now i am getting a vin miss match and car wont start. I am having hard time getting anyone to be able to program keys or read the immo for this. currently i have 1 original ecu and another ecu from another car. Are you able program the vin number to my 2nd ecu? Thanks for the help
@LMAutoRepairs4 жыл бұрын
Just program the vin to the replacement ecu... is that the only problem... Thank you for watching and for your comment!
@alevogod4 жыл бұрын
@@LMAutoRepairs do you have an email address? I need someone to do the work. can i mail in the eeprom or ecu? i am willing to pay. I kinda need this fixed asap
@johnhalm60205 жыл бұрын
Hello again. I want to find out how do i transfer immobilizer data from an ecu that has the immobilizer chip removed to another similar ecu. (Megane 1.5 dci).
@LMAutoRepairs5 жыл бұрын
Same principle... Look for the eprom and copy the data... Thank you for watching!
@ngoielongogilbert84793 жыл бұрын
Hi, that is a very nice job you are doing, keep it up thanks.
@LMAutoRepairs3 жыл бұрын
Thanks! 👍👍👍
@ngoielongogilbert84793 жыл бұрын
@@LMAutoRepairs Hi, I have got almost a similar case with a 2004 mitsubishi endeavour ecu MN132652. The ic47 which is 24c04 shifted from old ecu to new does not allow the car to start with the new, is there any other ic having immo information on the board?
@LMAutoRepairs3 жыл бұрын
Most likely the flash... if not external, will be in the MCU...
@ngoielongogilbert84793 жыл бұрын
@@LMAutoRepairs In the MCU? can I know which one exactly? Can it be the E338A? what do you think it will happen if I take it from the original to the new? Cause it is said E338A is a car key control ic. Can I read and write this chip? Thanks.
@mrasfalt5 жыл бұрын
hi . How to locate pin number one in eeprom
@LMAutoRepairs5 жыл бұрын
Each car is different... but look for repetition... There's some little softwares out there that will reveal the pin from the eeprom data... Thank you for watching!
@Mambre797 жыл бұрын
Thank you for sharing. Have some questions 1. What is the name of the eeprom adapter? Need to order it apart from xprog. 2. BMW EWS2 has MCU with security, if u try to read it onboard it erases the chip. Can I read it securely if I desolder it or maybe there is another safe way?
@LMAutoRepairs7 жыл бұрын
Mambre Khachatryan Thanks! 1. eBay search for 'soic8 adapter ' 2. never done that one... but I would remove the chip... X-prog is capable of bypass the security on some chips/mcu... not sure about the one in cas2... Google surely will give you some clues. Hope that helps....
@rk18drive134 жыл бұрын
why only the mobilizer cheap? what about the other data?
@LMAutoRepairs4 жыл бұрын
The ecu's were identical... So, everything else was good... 👍👍👍
@johnhalm60205 жыл бұрын
I think they had done that to bypass the immo. Is that a good thing. My new ecu is in and want to program it
@LMAutoRepairs5 жыл бұрын
🤔 You can't just remove the eprom to bypass the immo... Or I am missing something, or you are... Lol
@johnhalm60205 жыл бұрын
@@LMAutoRepairs how can i send you pictures to help me solve the problem
@johnhalm60205 жыл бұрын
an email will be fine if you don't mind
@LMAutoRepairs5 жыл бұрын
@@johnhalm6020 Visit the forum... kzbin.info/www/bejne/a3vPkKOle5holaM Myself or a fellow member, will be more than happy to help!
@johnhalm60205 жыл бұрын
@@LMAutoRepairs ok sure i will
@evils54455 жыл бұрын
Hi, great video! Please can you tell me if I can do this procedure for a Bosch Med9.1.1 for an Audi S5 pn 8T0 907 560? I have to swap 2 ECUs between them. Also which one is the eeprom chip inside? I can't find any details anywhere. Thank you very much!
@LMAutoRepairs5 жыл бұрын
Hi Don't quote me on this... but I believe that ecu has a 95160 eprom... so you should be able to esily swapped them... I am not sure is there is any data immo related on the flash... but you can swap the eeproms and go from there... Hope that helps. Thank you for watching and for your comment!
@gbbghhh81535 жыл бұрын
Did you get your S5 to work I think I need to do the same on my S5 i don't have any power on the ignition system
@Solimanreal6 жыл бұрын
thanks for sharing your knowledge
@LMAutoRepairs6 жыл бұрын
Thank you for watching!
@jasondambrun96215 жыл бұрын
Hello you do a very good job congratulations, I would like to know if a ecu hs but which starts anyway we can make a swap on another ecu? ecu is an edc15c2 bosch 2.0 hdi you have to swap eeproms 5p08 and 29f400? or only the 5p08? thank you in advance
@LMAutoRepairs5 жыл бұрын
Hi Only eeprom... Thank you for watching and for your comment!
@jasondambrun96215 жыл бұрын
Thank's
@Mik88995 жыл бұрын
Nice
@LMAutoRepairs5 жыл бұрын
Thanks! 👍👍👍
@temejumbo97945 жыл бұрын
NICE VIDEO. THANKS
@LMAutoRepairs5 жыл бұрын
Thanks! 👍👍👍
@rockyW465 жыл бұрын
Hello please could you help me, I would like to clone from me the ECU of the Audi A3 8P 1.6 c.c 75KW (102hp) petrol, I already own the receiving Ecu same code as the original one , you tell me the equipment that I need es the program to use? thank you very much for your help, greetings
@LMAutoRepairs5 жыл бұрын
Hi Not sure what is the ecu on that one.. But if the eprom is external, just do swap them... Otherwise you might need K-tag or similar... Thank you for watching and for your comment!
@rockyW465 жыл бұрын
Hi LM Auto Repairs ,thanks so much for the information, I tell you specific information ,the my ecu is : SIEMENS 06A 906 033 BB , SIMOS 7.1 (5312) thanks !
@LMAutoRepairs5 жыл бұрын
@@rockyW46 Just swap the 93c86 eeproms... and you will be good to go...
@majorkeys60492 жыл бұрын
Hi boss can i use Autel maxiim im608 to do this thanks i need your reply
@LMAutoRepairs2 жыл бұрын
Pretty sure yes... 👍👍👍
@Ashish7025 жыл бұрын
This experience is good sir please my help || indian car ecu immobilizer coding and programing same process??? Sir I have a macanik indian car
@reirizjose Жыл бұрын
Hi, have u ever had immo off on a EDC15VM+ ? thanks
@LMAutoRepairs Жыл бұрын
Don't I have ever done that one... 👍👍👍
@soufianattar45547 жыл бұрын
hey, great work. i am 4th year mechanical engineering. I want get deeper in this sector. can you please mention all the tools, software that i need; all the options that i have. i took a course in programming and microchip. i know C language, even assembly. thanks
@LMAutoRepairs7 жыл бұрын
Hi You know already more than I do then... lol Watch this video, it might help... kzbin.info/www/bejne/l3isg5KJjsdkoK8 Thank you for watching.
@soufianattar45547 жыл бұрын
i''ll do, what i do know a lot of things, but i miss the practice.that's why i was asking you about the tools, i'll see the video an i'll come back. Thanks bro
@joaovalente19937 жыл бұрын
Thanks for the video, it's very useful. A question, if you just want to deactivate the immobilizer? thank you
@LMAutoRepairs7 жыл бұрын
João Valente In that case, there is some data that needs changing... there is softwares out there capable of doing that with a click of a button... Google will help you to find more information about it. Hope that helps...
@randomthoughts8926 жыл бұрын
awesome video well said and done
@LMAutoRepairs6 жыл бұрын
asa fai Thank you for watching and for your comment!
@rejinc18937 жыл бұрын
Can you tell me from the actual readings, where i would find the skc number (immo number)? thanks great video
@johnhalm60205 жыл бұрын
Ok. But i mean the eprom has been removed when i got the car
@LMAutoRepairs5 жыл бұрын
🤔 Confused... If there is no eprom, there is nothing to clone... 🤔
@astroboyyo6126 жыл бұрын
Good evening, today I came to the garage an ECU with this same eepron which eepron equals 95080? Thank you
@LMAutoRepairs6 жыл бұрын
AstroBoy yo Hi I am a bit confused... What do you want to know exactly? Thank you for watching!
@astroboyyo6126 жыл бұрын
LM Auto Repairs tomorrow I translate it and I answer it thanks jjjj
@ryancolley76086 жыл бұрын
hi, can this procedure also be done with carprog and using a eeprom clip surplied with carprog? also can you not using a clip read the chip in place? great video and thanks for sharing!
@LMAutoRepairs6 жыл бұрын
Ryan Colley Hi Theoretically yes... But, if you can remove the eeprom, do it... the chances of a successful read is much higher, as you don't have the interference of the other components on the circuit... Hope that makes sense... Thank you for watching!
@ryancolley76086 жыл бұрын
LM Auto Repairs many thanks for your reply and info! ill bare that in mind, thanks alot!
@guille79bcn5 жыл бұрын
I spent many hours looking exactly for this information... I'm mechanic and I'm starting to do this kind of jobs. I built a Carprog and after watch your video and read the comments, I'm not sure if is necessary in my case: I have Citroen C5 - EDC15C2 ECU that contains serious damages on the board caused by one of capacitors, that exploded and burned a big hole on the base. If I'm right, you did a copy for use booth ECUs in the car, but in my case, you think that only changing eeproms from damaged ECU to donor, could be enough for start the engine? In advance, many thanks for your work, for make it that looks easy, and obviously for share it. Regards from Barcelona; Guille
@leewright61016 жыл бұрын
shouldnt you erase new chip before you write back clone info else it can cause bad data,
@LMAutoRepairs6 жыл бұрын
lee wright Hi Not on all chips... The program does check data by comparing it with the file after writing... Thank you for watching!
@lorobalАй бұрын
Hi, do you know if it is possible to change the chip from the original UCH to the second-hand one? If we do that, will the purchased one work or will we have to do something else? I am very good at soldering chips and I have the necessary materials.
@LMAutoRepairsАй бұрын
Should work depending on the UCH type... Some have all information on the EEPROM only, but some others contain information on the MCU as well... Which in that case would mean you would need to transfer both chips... 👍👍
@lupu72424 жыл бұрын
hello, where can I buy the wires for connecting the chip to the computer? and plug, also connect to usb? sorry for my english I'm Romanian 😁
@LMAutoRepairs4 жыл бұрын
The tool is called X-prog Thank you for watching!
@lupu72424 жыл бұрын
@@LMAutoRepairs 5.55 is still good?
@LMAutoRepairs4 жыл бұрын
@@lupu7242 I guess so... but if you are to buy one, get the latest version... is always better...
@lupu72424 жыл бұрын
@@LMAutoRepairs it's expensive😁
@LMAutoRepairs4 жыл бұрын
@@lupu7242 Look for the clone version...
@hudatehnik86103 жыл бұрын
Verry good.
@LMAutoRepairs3 жыл бұрын
😊 Thanks! 👍👍👍
@hudatehnik86103 жыл бұрын
I service the car ECU module too
@001KW97 жыл бұрын
Peugeot 206 1.6/MP7.2 Year 2000 - PP2000 gives Error Reading the ECU (the computer does not respond). ECU unlocked, no IMMO, but the car starts. Not yet read from BSI (HC05), read from 24C02 in MP7.2 but it is blank. Tested the connection from ECU pins 19, 20 and 44 to DLC pins 15, 7 and 3 is connection. What can the error be? Because ECU is not locked?
@donaldsampson49446 жыл бұрын
Hi How much would you charge. I need to fix my sprinter. It has start error. How can I contact you?
@canakbas37837 жыл бұрын
firstly sorry my english is very bad. i want to learn, if i swap ecu it is enough to change immo chip or no? why do not change the chip, why do you copy the data first chip to second chip?
@LMAutoRepairs7 жыл бұрын
Can Akbas Swap the eeprom would work as good... I have copied because I was asked to leave both ECUs to work on the same car...
@canakbas37837 жыл бұрын
I understand. Thank you for your reply to my message.
Ron Chaput Thank you for watching! EBay, if I recall correctly....
@sadikmamoun28477 жыл бұрын
thanks for the video as always informative
@LMAutoRepairs7 жыл бұрын
sadik mamoun Thanks...
@sicilia020219865 жыл бұрын
Hi. Hello, I want to change my ecu in immo off. Now I need help, is it enough to read the eeprom (5p08c3) alone and write an immo off?
@LMAutoRepairs5 жыл бұрын
Hi Yes... you can... Thank you for watching!
@sicilia020219865 жыл бұрын
@@LMAutoRepairs flash not is a pegeuot 807, 3 plug?
@El1avatar6 жыл бұрын
Si se cambia la ecu por falla se puede traspasar la memoria antigua hacia la ecu nueva ??? Evitando asi la programcion ???
@LMAutoRepairs6 жыл бұрын
Luis camaño Yes... that's exactly what I have done on this video... with the difference that I left both ECUs to work on the same car...
@matejaprskalo9985 жыл бұрын
What is called the EEPROM programmer?
@LMAutoRepairs5 жыл бұрын
In this case I was using x-prog... Thank you for watching!
@matejaprskalo9985 жыл бұрын
@@LMAutoRepairs Thank yuo
@scientist1003 жыл бұрын
Where did you get that multi pin adapter? Also, can carprog be used in a similar fashion?
@LMAutoRepairs3 жыл бұрын
I got it from eBay... Yes, carprog should also do the job... Thank you for watching!
@scientist1003 жыл бұрын
@@LMAutoRepairs if you don't mind me asking, where do you get diagram information regarding where to connect each pin? I saw you had a diagram but how do you get that information for a specific chip you have and how do you identify them, are they printed on the chip? Thank you!
@LMAutoRepairs3 жыл бұрын
Programmers usually come with some sort of instructions... Thank you for watching!
@brkofobija6 жыл бұрын
But if you do not change the number 484.26 in 385.08 (385.12) clone ECU doesn't work!
@LMAutoRepairs6 жыл бұрын
It worked on this two ECUs... which was what this video was about... Thank you for watching!
@jamesbarratt5932 жыл бұрын
What happens if you read say for example an ST93c66 chip with the setting to read not being ST but microchip. It reads but does that mean the data is definetly wrong or not?
@LMAutoRepairs2 жыл бұрын
Could be... either erratic data or fails to read... 👍👍👍
@jamesbarratt5932 жыл бұрын
@@LMAutoRepairs And if you matched a Renault traffic EDC15c to SAGEM bcm then 2 minutes later they became unmatched. Where would your mind be as to the next step to diagnose that?
@LMAutoRepairs2 жыл бұрын
Difficult to say... but I would onsider a bad bcm perhaps... Are those parts original from the car or similar?
@jamesbarratt5932 жыл бұрын
@@LMAutoRepairs the bcm is a replacement bought from Ebay. I learnt pin using my im608 pro then reset immo and my im608 said successfully completed. Then went to relearn and I can't recall but don't think it did it 100% yet got immediately distracted by seeing immo matched appear. Thats what I wanted to see and with it moved on. Only 2 mins later not matched. Also the central locking not working and every time I code a key, either im608 pro or TDB1000 it says completed but check and no keys stored.
@jamesbarratt5932 жыл бұрын
oh too add. pin 6 and pin 14 ohms were way out. turned out to be blue plug. cut it out and soldered wires together. after ohms 60 ohms on can
@christianrobertadzic93217 жыл бұрын
Hi mate! why you just not soldered the good eeprom to the new ecu?
@LMAutoRepairs7 жыл бұрын
Christian Robert Adzic Hi I have explained that during the video... I have been asked to leave both ECUS ready to work with the car... Thank you
@dudanken6 жыл бұрын
Have you tried to use pomona clips?
@LMAutoRepairs6 жыл бұрын
I always remove the chips... to avoid errors due to the PCB circuits... Thank you for watching!
@ind.subarumechanicmnsorens52004 жыл бұрын
And why can't you just swap the chips?
@LMAutoRepairs4 жыл бұрын
You can... but in this case I was requested to leave both ECUs programmed to the car ... Thank you for watching!
@kortufflpaua Жыл бұрын
Can you just swap it?
@LMAutoRepairs Жыл бұрын
Yes... 👍👍👍
@ind.subarumechanicmnsorens52004 жыл бұрын
How do you know what chip stores the eeprom data ?
@LMAutoRepairs4 жыл бұрын
Hi By the id written on the chip... Thank you for watching and for your comment!
@rteaw4 жыл бұрын
hmm, how this works.. why you copy data from org.chip to the other one. cant you just take the org. chip and put on the other ecu direct.
@LMAutoRepairs4 жыл бұрын
Hi Yes you can... in this case I was asked to leave both modules programmed to the car... Thank you for watching!
@rteaw4 жыл бұрын
@@LMAutoRepairs aaa okej then i understand. by just moving this chip, do you think i can do it on a edc16u34, i quess is the same process.
@LMAutoRepairs4 жыл бұрын
@@rteaw If is does have an external eeprom, yes... I never done one... I don't think... 👍👍👍
@HanifEFIMechanical Жыл бұрын
Good
@LMAutoRepairs Жыл бұрын
☺️ 👍👍👍
@armandonika6 жыл бұрын
Luis hi, im wondering how do you distinguish the eeprom from the CAN transceiver for example having both 8 pins??
@LMAutoRepairs6 жыл бұрын
armando nika Well, first you can look at the writing on them... Then, when you start to get familiar with the circuits, you can see by also looking at the components around them... The can transceiver for example, usually has a filter at some point in the circuit... Hope that helps... Thank you for watching!
@armandonika6 жыл бұрын
+LM Auto Repairs thank you im into this thing now because a lot of people cant afford a new module so this might come very handy with a used one 😀😀
@LMAutoRepairs6 жыл бұрын
armando nika 👍
@boosttapperformance86736 жыл бұрын
Where you get the tools to read the chip ? What's the name and where to bay them please send a link or send name and description
@LMAutoRepairs6 жыл бұрын
savage life chovoy Hi There is different tools out there capable of this... X-prog, upa, xhorse etc... eBay is a good place to look... Thank you for watching!
@boosttapperformance86736 жыл бұрын
lmsvvavr I found the tl866 mini pro to be my choice however I would love to know if you could make a video doing a Bosch ME7.5 VW/AUDI IMMOBILIZER OFF OR SET TO PROGRAMING MODE?
@LMAutoRepairs6 жыл бұрын
savage life chovoy If that job comes around... no problem...
@markchris11406 жыл бұрын
hi did you first erase the date on the new chip on which you copied the older data from the bad Ecu chip?
@LMAutoRepairs6 жыл бұрын
mark chris I usually erase the chip first... But some chips you just just write over the old data... Hope that helps. Thank you for watching!
@benoitbourdaire41945 жыл бұрын
Could it be done with magnetti ECU?
@LMAutoRepairs5 жыл бұрын
Yes... Thank you for watching and for your comment!
@macarenabiondi64385 жыл бұрын
Hi, can I read and write this ECU edc15c2 with the k-tag? thanks, greetings from Argentina.
@LMAutoRepairs5 жыл бұрын
Most likely yes... Thank you for watching and for your comment!
@macarenabiondi64385 жыл бұрын
@@LMAutoRepairs thanks, I will try! 👍👍
@garpoonbs96475 жыл бұрын
Hello. Please tell me how to connect the eProm 5P08C3 to the xprog 5.55 programmer
@LMAutoRepairs5 жыл бұрын
Hi Watch the video...
@garpoonbs96475 жыл бұрын
@@LMAutoRepairs watched twice so how to connect?
@LMAutoRepairs5 жыл бұрын
@@garpoonbs9647 🤔 You just insert the chip in the adapter... What exactly are you looking for?
@garpoonbs96475 жыл бұрын
@@LMAutoRepairs tried to read the clothespin, did not work took the adapter 150 mil how you read everything.thank you very much