CNC Shield V3 Relay Control

This video is about CNC Shield v3 Relay Control
Control a DC Motor / Laser module with Arduino + CNC Shield V3 and Relay
Share, Support, Subscribe.!!!!!!!
Subscribe: / @makertutor101
Please Donate To Help Me Afford New Equipment And Software To Make My Videos More : goo.gl/1m8Dg2
→ Don't forget to subscribe!
🌟Love you all! 💕
THIS VIDEO IS FOR EDUCATIONAL PURPOSES ONLY!

[@imranfoodtech]

You are always simple and helpful

[@aeltonftome1260]

You is Best of the web !...Great

[@THEEVIL969]

Muy bueno tenía la duda de las diferentes versiones de grbl y me las despejaste gracias..

[@cornelisachtenzestig5533]

Thank you so much for your video. Very clear and simple!

[@screeningstudio3868]

Hi if i want to use this relay for triggering plasma torch using cnc shield with grbl 1.1h, am i need to use Z+ pin also?

[@spplS.]

Haha after a long journey through the internet I've finally found somebody with the exact same problem as me. I also want to control a plasma flame through a relay connected to the plasma cutter. How did you solve it?

[@ardypamungkas9505]

So the motor will be ON after start (engrave) button program or after turn ON power? 🙏... And how to combined with speed control?

[@dirtysanchez2k]

Is it set at one speed? Can you fluctuate for different cutting material? Or is this just proof of concept.

[@alpertintas4771]

hello nice job ,so how to adjust spindle speed ? thanks a lot.

[@BebenX]

Hi, is it possible to control this spindle speed using the cnc shield?

[@poco3xpro885]

May i know,what method if im using relay for spindle using vfd, is there need some setup for parameter on vfd.

[@daengrani9610]

What if using brushless motor dc as spindle??

[@atifali4703]

its good but where we connect end stop switch of Z axis.

[@ittybittyinnovations5983]

Can you please share the links for softwares for laser engraver with Arduino uno and cnc shield, also which softwares you used in the video

[@asaazaq3019]

👍

[@Maax3dledesma]

Hola para el spindle utilizo una fuente de PC de 600W y para el arduino utilizo una fuente de 12v 1.5amp, para hacer esto puedo utilizar solo la fuente de PC? Mi spindle es de 12v

[@TnInventor]

i have grbl 0.9, the spindle works with Z+

[@danielpdrummer]

I have a question, is it the same connecting a laser module? Is the same way to connect a laser?

[@brunocabral1578]

Why use the 5v and GND at left side when there is a nearby 5v and GND at right side?

[@nsk6914]

Is the relay spdt for its the normal relay module

[@ste76539]

Err this video doesn't explain anything. Why show the sig pin of the relay being wired up to the spindle enable pin, only to scrub that out and reconnect it to the Z axis end stop pin? It doesn't make any sense unless you explain why, but you haven't explained anything at all. If you need to use the Z axis end stop as a spindle enable pin, what are you supposed to do for a Z axis end stop?

[@PotNanny]

Use the SpnEn pin for the Z axis endstop. This is a known bug in grbl (or arduino, I don't remember).

[@JackInTheFrost]

I was wondering the same thing, I found the explanation in some code I was checking "NOTE: IMPORTANT for Arduino Unos! When enabled, the Z-limit pin D11 and spindle enable pin D12 switch!" openbuilds.com/threads/spindle-how-does-it-work.6967/

[@HS-dz1hr]

Hi, It's nice. How did you change the config.h code in Arduino Lib?

[@alper4856]

thank you so much but now m3 command turn off the spindle and m5 turns it on can you help me please

[@Ed19601]

All questions about 'how to set spindle speed?' You do that on the spindle. A relay can only switch on and off

[@056_asadfakih5]

thank youuu

[@Maax3dledesma]

En un arduino nano con shield v4 se puede?

[@conradlothran5796]

Nice! Would this word with a laser module?

[@MakerTutor101]

Yes

[@wiebercraft4974]

What relay are you using?

[@zeusam]

S1000;M3 ???

[@myambition3801]

mam how was relay voltage and spindle motor voltage

[@cadchannel3921]

Don't work for me, can you help me to fix it?

[@typ1804]

Hey. I'm just working on this problem too and I can't get it running. Did you change any firmware stuff? And what gcode did u use?

[@MakerTutor101]

Hi I do it for you kzbin.info/www/bejne/pXLEkKltfd2dnLs

[@nikoanggriawan303]

how if we use ssr sir ? can ?

[@hobbyking8817]

Can I convert servo to laser mod

[@leandrogonzalez2820]

te envie un mail con un proyecto , leelo gracias.

[@somsakhua2317]

i try this but my spindle 500w is not move .why

[@cesaralejandrofernandezbac8367]

You may need more power than 12V

[@Pamikirand]

Kok z nya gk kluar signal ya gan

[@TheBunnyBashers]

Will this work with L298N?

[@cesaralejandrofernandezbac8367]

And trying to figure it out right know, have you done it?

[@Wolf7922]

IT DOESN'T WORK!!! I CHECKED IT! НЕ РАБОТАЕТ! GRBL 1.1F