*Did you notice the pocket clip on this knife? Click on the link to watch how I modified a Ganzo Firebird clip to fit the Code 4:* kzbin.info/www/bejne/d6jJlpZoa8tnbpY
@TheKnifeBeater5 жыл бұрын
Fantastic idea Richard, thank you!
@TheKnifeBeater5 жыл бұрын
I sure will Richard.
@TheKnifeBeater5 жыл бұрын
Ok, you bet Rick. Thank you.
@ScottieG595 жыл бұрын
I notice you left the lock pivot and blade stop pins in place. For those who do remove them, be careful not to mix them up. If you put the lock pivot in the blade stop position, it can cause vertical blade play, as the lock pivot pin is slightly smaller.
@TheKnifeBeater5 жыл бұрын
Yes, excellent tip Scott, thank you.
@carknelson58955 жыл бұрын
Cool to see inside, that lock is really in deep! That explains why I have to push so hard to unlock it! Thanks
@TheKnifeBeater5 жыл бұрын
You bet Cark, thanks for watching.
@mi20924 жыл бұрын
My Code 4 came with oil dripping out of it and when I pressed the back lock to close it the blade dropped on my finger. A blood sacrifice to the knife god lol🩸 You are absolutely right about not using lubricant on it.
@GratefulPanick5 жыл бұрын
This video was super informative and very well shot! I like your style, brother! Thank you for sharing!!
@TheKnifeBeater5 жыл бұрын
Thank you very much GP.
@majergens5 жыл бұрын
I thoroughly enjoy how-to videos such as this! Nice job. 😀
@TheKnifeBeater5 жыл бұрын
Thank you Mike.
@paddyspotatopeelers21545 жыл бұрын
Great tutorial mate. Very simple design for such strong lock. Funny you showed your sticker im going on monday to order mine hopefully. Atb paddy 👍😄☘️
@TheKnifeBeater5 жыл бұрын
Thanks pad. Let me know when you get those, I would love one. I'll send one of mine your way.
@paddyspotatopeelers21545 жыл бұрын
@@TheKnifeBeater you would be one of the first to get one mate. After all you have done for me. Atb paddy 👍😄☘️
@sunshyn215 жыл бұрын
Thanks for this video! I have always been wary of taking my recon one apart, but you made it feel very manageable. I think I may hit you up on one of those stickers for my knife case 😉
@TheKnifeBeater5 жыл бұрын
Happy to hear that sunshyn. If you send an email to theknifebeater@gmail.com with your info, I'll send you a sticker. Thanks for watching.
@redastrachan89784 жыл бұрын
*SUBSCRIBED*
@SteveKluver5 жыл бұрын
Very good J. Thank you much, for doing this. I have never taken either of my Code 4 knives apart before. And, have never seen a tear-down video of one. It looks good in there. Did you by chance, measure those washers, while you had it apart?
@TheKnifeBeater5 жыл бұрын
Sorry Steve, I didn't, but I will for you. Diameter and thickness?
@SteveKluver5 жыл бұрын
Yes, thank you @@TheKnifeBeater. I.D., O.D., and thickness of each.
@stevebowman905 жыл бұрын
Nice video Jay. I’ve taken my Endura apart. I’m still curious as to what makes a Triad lock that much better than anybody else’s backlock. I’ve been eyeing Cold Steel’s products and have wondered, is it stronger? Easier to deploy/engage? Anyway. Thanks for the demonstration!
@TheKnifeBeater5 жыл бұрын
Honestly Steve, I don't know if the Cold Steel back lock is any stronger than Spyderco's. I think a lot of that hype is perception due to those lock strength test videos, where Cold Steel hangs a refrigerator from one of their knives.
@hyssean125 жыл бұрын
@@TheKnifeBeater are you kidding me? There is a stop pin in the cold steel lock design. A normal lock back just uses the rocker arm. A immovable stop pin is a lot stronger than the lock bar of a Spyderco. Read cold steels page on the tri ad lock to see why it is stronger.
@TheKnifeBeater5 жыл бұрын
In theory Sean, I would agree that an immovable pin would be stronger. I myself haven't tested the two against each other, which is why "I don't know which is stronger". The Tri-ad lock is without a doubt insanely strong.
@birdlaw10195 жыл бұрын
Love these disassembly videos, great job! The code 4 is a beast of a knife, too bad it scares people in my neck of the woods, I would love to be able to carry it more. Just a note, your sound was a bit wonky in this one, did you change your setup?
@TheKnifeBeater5 жыл бұрын
It really is a great knife. Kinda sucks about the sheeple by you BirdLaw. Did you notice the sound issues when I switched to the closeup view? If so, it's because I'm still trying to get the sound right when using that secondary camera. I have a mic on the way for that one, sorry about that. Thanks for watching.
@Brucelyroy5 ай бұрын
Does anyone know the bearing dimensions for an upgrade?
@TheKnifeBeater5 ай бұрын
I don't, but I like where you're going with this idea.
@Anurahm_Kycor4 жыл бұрын
Wish I had this video when I first got a cold steel. I just started taking shit apart. Ended up flipping my two rigid pins and making the lock malfunction. Turns how no matter how close they look they are not the same.
@TheKnifeBeater4 жыл бұрын
Sorry to hear about the trouble with yours. At least you will be prepared for your next Cold Steel disassembly. You'll end up becoming a Tri-Ad lock master. thank you Nathan.
@kenmastersmaster Жыл бұрын
No liners? Wtfff
@Keith_the_knife_freak5 жыл бұрын
Nice. Work. Except why ya gotta be a lefty??? 😂🤣🤣😂
@Keith_the_knife_freak5 жыл бұрын
@Richard Davis 🤣🤣😂😂😂😂😂😂
@TheKnifeBeater5 жыл бұрын
Thank you keifer. This video will answer your question: kzbin.info/www/bejne/b4LIgKx9opmkhJI
@jshphysicistatyahoo5 жыл бұрын
Knife Beater / Wife Beater - that's kind of a f---ed up name man. Disassembly was informative so you get a like. But wife beater, really?
@TheKnifeBeater5 жыл бұрын
Sorry to hear you are offended John, certainly not my intention at all. When I came up with the name, my thought process about the "Beater" part was beater blades/knives, user knives that are relatively inexpensive to replace. I understand you have no idea what my actual moral character is like, but having grown up in a household full of domestic violence, my channel name is NOT a play on words.