No sir, I’m the one that appreciates you and your support. Thx for commenting.
@bradenwhite43563 жыл бұрын
Sick to see those bad boys finally in action
@3rdPedalMedia3 жыл бұрын
Yea sir!!! Continued the etuning. Car pulling awesomely.
@fernandohood554210 ай бұрын
Clearly many do not understand how the ventilation system works. In relation to the bigger intakes the air velocity is slower (Daniel Bernoulli) making the output voltage from the MAF lower.
@3rdPedalMedia9 ай бұрын
Without active forums a lot of ppl mindlessly mod their cars not understanding what makes or removes power.
@ezkoshows7136 Жыл бұрын
For the air port that you said people block off, it looks like the z1 3” intakes come with the hole so you can just put the rubber hose they give you. Kind of like the 2.5” intakes, so would that save me the hassle of doing all that you did to get rid of the vacuum?
@3rdPedalMedia Жыл бұрын
Correct.
@ezkoshows7136 Жыл бұрын
@@3rdPedalMedia thanks for replying so quick, got yourself a new subscriber! 💪🏼
@3rdPedalMedia Жыл бұрын
@@ezkoshows7136 thx for the support.
@faduhfade773 жыл бұрын
Would u recommend the Coolant/oil catch can from Admintunning. I wanna buy it but I don’t see a baffled catch can system keeping things from going back in. What do u think ?
@3rdPedalMedia3 жыл бұрын
Combo cans are great. I have one coming from a vendor I’m keeping quiet. Lol. So that type of can it’s vented. There is no suction to go back into the engine.
@kolbyfitzmaurice8547Ай бұрын
Jus got 3 inch long tube STILLEN cold air intakes was wondering if u need a chip to access the ecu or if I can get it dyno tuned without wasting money on a chip
@3rdPedalMediaАй бұрын
I don’t believe stillen ever made 3” intakes. 2.5” intakes don’t require a tune but it helps. 3” intakes require a tune.
@FRYD2THEMAX7 ай бұрын
You can actually vent the back two Pcv ports if you have a catch can because the catch can used the ports on the intake manifold
@3rdPedalMedia7 ай бұрын
That will pull in unmetered air and cause bad idle and lean problems from the excess air.
@FRYD2THEMAX7 ай бұрын
@@3rdPedalMedia never had that issue
@kuls1113 жыл бұрын
Great info I'll be doing this also btw Are those juke seats or 370 Nismo seats
@3rdPedalMedia3 жыл бұрын
370z Nismo.
@ıîırpra777amaıîı Жыл бұрын
The man 🙏🏼
@3rdPedalMedia Жыл бұрын
The Bro 👊🏽
@Aaron-wp1pz3 жыл бұрын
Did you notice gains when switching from Takeda intakes to the 3" Admin?
@3rdPedalMedia3 жыл бұрын
Oh yea the butt dyno definitely felt it. Any 3” should yield some good results.
@koolaidman4461Ай бұрын
Im installing admin 3in intakes on my dyno day, is it okay if I leave the PCV system as is for around a few days to a week before I get the kit or do I NEED to do something about the PCV right away?
@Highwayvillian.6 ай бұрын
Are the fittings that go into the valve cover restricted of a free flow?
@3rdPedalMedia6 ай бұрын
Rly should be. It’s not really a pressure line so it should affect much.
@roadtoamilli16803 жыл бұрын
You did Etuning right ? Because I’m doing the opposite I’m going to trailer my g because the tuner will be two hours away from me. So we’ll see how that goes .
@3rdPedalMedia3 жыл бұрын
Yea, no one really close. Finally got the car back from doing the gaskets and now finishing up the etuning
@v0rx3x_bltz773 жыл бұрын
Could you just throw 4 small filters over the crankcase vent and pcv valves and cap off the manifold?
@3rdPedalMedia3 жыл бұрын
Technically you can. But they the blow by gasses with condense to the closest cooler surface and create an oily mess under your hood.
@roadtoamilli16803 жыл бұрын
Hey Kevin! Looking back at this video it looks like I made a mistake by only capping off the lines. Just today I start to notice lots of white Smokey air come out of one of those lines! Do you know what might be going on ?! Thanks un advance.
@3rdPedalMedia3 жыл бұрын
Post some pics to your IG and tag me.
@DharsanDevendran10 ай бұрын
Could i put 3 inch pipe cold air intake on infiniti fx50s 2011 without any problem
@3rdPedalMedia10 ай бұрын
Shouldn’t you tune it. Unknown also if you may run into routing interference of the tubes.
@xero0pacity8810 ай бұрын
hey where can i find fuel hoses for the g37? for the ac lines
@xero0pacity8810 ай бұрын
pls reply i got the 3 inch intakes and dont want them rubbing against the ac-lines on the driver side, where do i get those fuel hose protectors from
@3rdPedalMedia9 ай бұрын
Any auto parts store will have it.
@xero0pacity889 ай бұрын
@@3rdPedalMedia thank you, so is there a certain size thatll fit on them? Or do i just go up and ask for fuel hose and itll be the same thing?
@3rdPedalMedia9 ай бұрын
@@xero0pacity88 yea just ask for fuel hose by the foot. Get about two feet.
@xero0pacity889 ай бұрын
@@3rdPedalMedia thanks for the help, also, im going to be installing catless downpipes/ test pipes and 3 inch long tube Z1 intakes, first 2 mods ever and im getting a stage 2 tune from z1, how much hp u think ill gain crank, im thinkin hopefully around 30-40hp crank
@mrgasbaby8 ай бұрын
so if i have dual catch cans, and get 3in intakes… do i have to get rid of my catch cans for whatever this is honestly i understand cars very well but this is something i just dont understand
@3rdPedalMedia8 ай бұрын
Catch cans are for the PCV system to stop blow by from going back into your intake system to reburnt. Depending on your intake sometime depict the catch can setup.
@EzeeFTW Жыл бұрын
What if I want to add catch cans , do just leave the pcv breather as is with the filters ?
@3rdPedalMedia Жыл бұрын
if its a recirculating catch can it will be in-between the two ports, the video illustrates the atmospheric setup.
@EzeeFTW Жыл бұрын
@@3rdPedalMedia I wanna do the mishimoto dual catch cans & it only has 2 ports for each can , so am I fine just leaving the breather with the filter ? Like the way you had it in the video
@mountaindewmofo Жыл бұрын
I have a p0300 code on my 08 g37 coupe ... i have changed the plugs, coil packs, silocone intake hoses, pcv delete and my car is still retaining the p0300 code and is now randomly overheating so its off the road til I figure this out ... anyone have any ideas? my only idea is to change the spark plugs again but use OEM instead of the crappy ones they gave me at autozone and replace the thermostat to fix the overheating.
@3rdPedalMedia Жыл бұрын
I haven’t ran across that one. But found this forum thread see if it sheds some light www.the370z.com/engine-drivetrain/126330-multiple-cylinder-misfire-p0300.html
@-draydogg-89393 жыл бұрын
очень круто!
@3rdPedalMedia3 жыл бұрын
Благодарность!
@binli19563 жыл бұрын
I’m running add w1 dual oil catch can with 3 inches admin intake, what is best correct way to install
@3rdPedalMedia3 жыл бұрын
Plz explain how you have it currently routed
@binli19563 жыл бұрын
@@3rdPedalMedia best way could I send you the pictures to identify
@3rdPedalMedia3 жыл бұрын
@@binli1956 send via ig
@binli19563 жыл бұрын
What is your ig account
@marquisbrown79373 жыл бұрын
I have catch cans and my car still has that vacuum 👀
@3rdPedalMedia3 жыл бұрын
Oh noes. Check my TikTok, the fix video and see if yours is like it.
@3rdPedalMedia3 жыл бұрын
What catch cans do you have?
@fernandohood5542 Жыл бұрын
All that explanation yet your throttle body is smaller than the 3 inch intakes🤔
@377ndacut Жыл бұрын
Doesn't matter Does not really hurt power
@3rdPedalMedia Жыл бұрын
replied to your 1st comment since you want to keep posting about this