Compact wood splitter.Restoration repair!

Hello everyone! In this video I bought an old wood splitter that was oozing oil and it didn't work very well ..
Rollers for rolling - ali.pub/5du85h
Tungsten Carbide Drill Bits - ali.pub/506rlq
Digital Vernier Caliper - ali.pub/2xz6z2
Side Cutting Drills - ali.pub/2xz6ue
Step drills - ali.pub/2tk510
Welding magnets - ali.pub/2tk4q4
Electric screwdriver - ali.pub/2uhwat
My mail - [e-mail]
My instagram - terafox80
Original video - • КОМПАКТНЫЙ ДРОВОКОЛ! С...

[@vy10mac9]

I've split 5 cords through it so far. Does what I need it to. kzbin.infoUgkxUyQswtttSffRMblGbrhCvZn7JkhtG1-7 I scrounge all my firewood and am not equipped to handle big wood, but for logs up to 24 inch diameter or so, it works great. I've been amazed by some of the gnarly bur oak and elm crotches it has split. For the tougher stuff within it's size range, you might have to study the piece a bit to decide the best attack, but if you split smart it's up to the job. It did arrive low on oil, and I was would have nicked it half a star for that, but it has regained my full confidence. UPDATE NOVEMBER 2021: Still going strong after all these years. I love the one-handed operation. Hope it's still in production if I ever need to replace it

[@norwegiananalogue3465]

Nice! I was ready to throw my old log splitter as it leaks oil and i am no mechanic. But here you come to save the day :) More or less exactly the same engine so here we go!

[@miker.8847]

Hello, very nice video - good job. had problems with my similar wood splitter ventile. then I saw your video and at 5:32 min you used 2 washes under the level mechnism. I did this as well and my splitter from 2012 works perfect now. You saved my spliter and my money. many thanks Greetings from Germany ---> sorry for my bad English ;-)

[@marksavage]

Well done bud , many thanks

[@andrewly6954]

I’ve just done the same job on mine. The seal at the end of the aluminium gland was destroyed and so could not build up sufficient pressure to split logs. I couldn’t find the correct two-part seal (o ring at the bottom and a hard “guide” seal on top), so I just shoved a fat o-ring instead and it works perfectly. I believe it was a 327 o-ring size. Have split a few logs so far hopefully it holds up.

[@andrewbroer3016]

Where did you get your seal kit from ? Having a problem finding one. Any help out there

[@frekkledipped]

great vid! If i took mine apart like that id never remember how it goes back together😄iis not working very well its just like this one might have to give it a try

[@fulwoodphantom]

Great job 👌

[@michaelshakib7777]

Thanks for the video. What is your advice for a splitter that goes forward ok but does not return very well. I noticed yours did that and then you showed two arrows and then somehow it was fixed!

[@thomassalgert9976]

Good work

[@datfire1984]

Hello! Thanks for the video very super. I need to replace a cylinder stem, but what I missed in the video is that of the spring and how you squeeze it back so it can be screwed back. Thanks in advance for the answer.

[@Kntryhart]

Thanks for the video! I need to work on the motor. Is there anything mechanical that secures the motor shaft to the pump gear or does the motor simply slide out? Thanks!

[@notfound379]

Thanks for the tear down. Just what I needed to decide I'll just put cardboard under it to catch the minor leak and just refill it from to time. :) Seriously, good vid but unsure I can find those seals tbh.

[@BOKEHMASTER]

Excellent rebuild. Thanks. I subscribed as well. Cheers.

[@scottlittle8380]

good camera work!

[@MrTrollHunter]

Where did you get the new seals for the hydrolics?

[@jeanriviere-js9mg]

Super ta vidéo la mienne avance lentement pas de force condensateur bonne état

[@goaro2007]

How did you put the cylinder back in. how do you compress the spring?

[@cedricbegu3808]

Hello , thank's for this vidéo , could you said where did you bought o-ring kit please ?

[@goaro2007]

hi, how did you compress the spring? thanks

[@lloydcud]

Dec 13 2023. Great video . I have the same splitter . Ram won’t operate . Blower fan turns fine . I took it apart , gears seem fine on motor and ram end . Oil was very black and dirty . Is there a filter that can be changed.

[@craigstumbaugh3860]

Where did you find the seal kit you showed in the video at 3:40?

[@JackyWalraetLuthier]

Thanks for the video ! I have the same machine and sometimes the engine will not start, but when I turn the fan it starts again. The collector is probably dirty. Can I reach the collector from the fan side? Thanks in advance!

[@scottlittle8380]

thank you Talking would really help Cheers

[@Patriottoo2]

Superb work! How did you obtain replacement O rings?

[@rodneypeterson9301]

Where do you get parts, I need pump gears, ty

[@TheMaskOfHappie]

Where you found new repair kit with o-rings??

[@davemulvaney435]

Where did you find the replacement parts ?

[@TheVideoZombie]

So where did you find oring-kit?

[@pullmyfinger6932]

Anyone get an answer on where to get the o-ring kit? Or even just the part number?

[@garymiller1216]

I have this same splitter, i know there has been no reply's to this vid and comments, in the show more he has the original vid where he commentates and explains what he is doing, i changed the subtitle to English and got all my answers, hope you do too

[@marcusseger2583]

but still no links to get seals and o rings or any parts damn it

[@k.d.8924]

link to the rebuild kit would be awesome

[@warrenjappe8637]

Doesn't anyone have issues with the welds on the RAM breaking? Can't seem to find any info on it. It looks like I'd have to take the whole backend of it apart on my WEN 6 ton machine

[@martinhoffman6923]

Intressant video. Jag ska renovera en likadan maskin. Var får man tag på nya tätningar?

[@tim_peaky]

does anyone know how to set the return pressure valve? Like maximum pressure? the part with the little ball an spring. i suppose you count the rotations of the screw?

[@lechiffre5452]

The last peace an endboss?

[@jordanscott9231]

Does anybody know a torque spec or how to alighn the rods. If I more than hand Tighten the bolts it won't return

[@LLythyrcaru]

Great video, I will give it a go but I am not sure how I will compress the spring ? also could you please let me know how much hydrolic oil is required for this type of log splitter. Many thanks

[@jerrymcg3199]

No video that I have seen shows the compression of the spring for reassembly. My splitter is still lying unassembled. However they usually take 3.5 litres of oil, maybe slightly more.

[@bryanteal]

Great video, except you omitted the hardest part, I believe. Compressing the spring, in order to screw on the new piston disk, is very difficult unless your spring has become weak. Your spring looks strong. Like I said, great video!!

[@franklinohrtman282]

Did you find a solution? We have the same problem and are working on a tool with thread rod and steel plates to compress the spring while reassembling.

[@jamesbullock7206]

@@franklinohrtman282 Just done this repair. I used a tie down strap with a cam buckle. Fed one end of the tie down strap between the spring and piston for most of its length, connected both ends together and pulled hard. 3 or 4 hard tugs on the tie down were enough to compress the spring more each time (the cam buckle locks under tension) and it let me chock the end of the piston with a block of wood. Once done remove the tie down strap and install the piston sleeve over the spring.

[@Timbuk24]

i just done it too. I didnt use any extra tools, it waś possible to compress the spring with the screws. I tightened the backplate screws and it all pulled itself together. One hint for the "family diy" guy: you need to open the little bleed screw at the front plate while using the machine. close it for transport :)

[@goaro2007]

@@jamesbullock7206 Do you have pictures of that ?

[@LLythyrcaru]

Great video but the most important part how to compress the spring is not shown, I have my splitter all in bits and cleaned up but I cannot figure out how to compress the spring anyone knows a different video that covers that part?

[@redl1newrx1988]

How did you pull the 4 rods so easily?

[@robertjohnston5241]

mine trips the breaker ??? anyone know what would cause that ??? thank you

[@Phiyedough]

It is good to see one of these actually splitting thicker logs. I bought mine secondhand and it will only split thin logs. I didn't know if it was faulty or just a weak design of splitter.

[@ralfjuch7797]

Was für o Ringe benötigt man, was ist das für eine Dichtmasse und welches Öl wird verwendet. Wo kann man das alles kaufen oder bestellen

[@veroee9184]

Que Aceite usa??

[@jerrymcg3199]

I've watched all the videos on these log splitters and I have never seen a single one that shows the reassembly. One minute the parts are lying there and the next minute they are all reassembled, as if by magic.

[@krypticlock]

Where did the seals come from

[@user-wz5my2lr6l]

Где вы купили рем комплект манжетов и колечек

[@reioXyhi]

why didn't he drain all the oil before disassembling? One more, that spring, is it hard to get back? One pair of screw clamps, could that be used?

[@Christopher-ib6kv]

My fan in the motor wont spinn and i vant remove it…any tips?

[@tunercamp]

내가 필용한건데 만들어봐야겠다

[@frekkledipped]

☦🛂🚾🚼🔞🔃⁉

[@joebirley2298]

Anyone know where to get the O-rings kit? uk

[@dawsonanstey9557]

I repaired my King 5 ton due to oil leaks. Perfect I thought....but after a week or so I noticed occasionally it would not start. It acted as if the start capacitor was open. The motor would sit and hum. The 47uF capacitor is not the problem. Sticking pump gears is not the problem. Its almost like when the rotor stops at a certain point it will just sit there and buzz. If I take a small screwdriver and turn it just a nub, its then ok until the next time. This is a single phase with no brushes and no centrifugal switch so it kinda has me boggled. Anyone have a hint?

[@dawsonanstey9557]

@@JamesW76 actually with the motor taking out and sitting on the bench it will do the same occasionally. Something wrong with the motor. I swapped it out and All is ok. Thanks James.

[@Andrzej228]

W mojej łupiarce mam problem z cofaniem. Nie wiem co dokładnie odpowiada za taką usterkę. Jakieś pomysły mam ale czy uda mi się to naprawić.🤔

[@MatejKos-cr4td]

Hello, where can I order the parts, thank you

[@tomasznajraw5314]

Wielki minus to likwidacja sadu. Takie drzewa ratuje się najdłużej jak to możliwe. Co do łuparki to jeszcze bardziej można poprawić fabrykę i obydwie ręce wolne.

[@florinnancu8718]

Dispicatorul meu numai are putere, cum îl pot repara?

[@426superbee4]

That the reason blew the seals out! By not opening up the bleeder value! That the 1st thing you do is open it up, 3 or 4 turns. When your finish close it off >> it up there on front with a WINGNUT

[@zoizoi6843]

I have problm with wood splitter He don t have power He haw some power one minute and later no power What is problem?

[@ruedigerst.3972]

Man sollte schon erklären was man da macht. Sicherheitsvorkehrungen außer Betrieb setzen?

[@dawsonanstey9557]

Notice you used paste type sealant (Black) on End Frames as opposed to Rubber-Ring seals (gaskets). What type of sealant was it? Also appeared to be no O Ring seal between Pump and End Frame extension when you dismantled but you did use one on assembly. When I dismantled my 5 ton King the O Ring was missing also. Curious if I should use one. The mating metal surfaces did not leak before. Eventually decided not use the O Ring and joint did not leak.

[@Patriottoo2]

I have used black RTV sealant on my last two rebuilds, and it didn't leak. Since there is just atmospheric pressure inside reservoir, the seal only needs to resist seepage.

[@dawsonanstey9557]

@@Patriottoo2 Thanks a million Patroit....I ended up using Permatex® the Right Stuff® Black Instant Gasket Maker, 147-mL Expensive but perfect.

[@rusekrusek1238]

Witam gdzie kupić uszczelniacze

[@yeagerxp]

Excellent work👍👍👍 . Thanks for sharing. Did you feel good @ 10:23. How many four letter words did you use? 🤣😫🙄

[@Joe-jz2dw]

Where's the link to the replacement parts? We all know where we can buy a drill and bits.

[@ImNewbeh]

My electric log splitter stopped working, when I plug it in and press the start button nothing happens, (motor not making any noise) any idea what the issue could be ?

[@coryanderson7581]

im having the same problem Bullshizle...did you ever find out anything?

[@wilkey40]

If it is not making any noise at all I would replace the capacitor

[@rickdsanchez6452]

Mine was the capacitor and corrosion on the button contacts

[@giorgiobenobre4393]

sorry, the engine on the side of the fan, runs clockwise, or counterclockwise

[@pavelliska8129]

Macher - superman

[@hansvanbeek688]

Weet u waar dat setje afdichtings kan bestellen

[@renkemam]

Heeft u nog een set kunnen vinden?

[@daganhaddad]

mine keeps eating capacitors - no clue

[@960wattoffgridrv]

suddenly I saw a potato cannon laid out across the bench.

[@theoriginalchefboyoboy6025]

where did you get the replacement seals and gaskets?

[@rockystelone21]

Similar problem with this other guy he has a 3D Printer and made his seals

[@fredwinner7679]

Sure would be nice if you explained what you were doing. Several things are not clear at all.

[@amerikanstafford]

Why is it so slow???

[@fredwinner3910]

What you doing need to slow it down and explain what the heck you're doing