Comparing, testing the most popular revolver speed loaders (feat. HKS, Safariland)

[@algarbarino8538]

Good video and demonstration. I carried HKS speed loaders when I worked in law enforcement. They were easier to grip in an emergency even though they jingled a bit. I never had a problem with them.

[@ldbrush9941]

Many years ago I carried HKS speed loaders for a N frame. Once I started wearing long pants and was hired I always carried Safariland, either comp 1 or comp 2 speed loaders until I was finally forced to go to a auto loading pistol. I have personally had HKS speed loaders dump the rounds on the deck pulling them out of a carrier as the rounds were heavy enough to turn while holding it by the handle. The 'secret' to carrying a Safariland speed loader is having a pouch you grab it by the body of the loader. The absolute cats meow for concealed carry is a Safariland loader carried in a JOX Loader pouch. Give Nick a email, he is a one man operation so speed is not on your side but they are by a very large margin the best carry method I have ever used.

[@lugin4guvistf773]

Good review! The Biggest Advantage to the Safarilands are the lesser amount of fine motor skills required to do the reload. Nice to see an Honest Review of the HKS's as well! Both can work well when being used properly, with a slight edge to the Comps 2s

[@garrettgarces4424]

Great review, you’re a great narrator. Not getting off track, honest comparison, and important info with demonstration, not much more you could want!

[@BlackcatOutdoors]

I usually use the hks. I find them easier to line up with the cylinder. I could see someone being able to do a quicker reload with the safariland with practice, but I tend to fumble around more with them.

[@hanss9431]

Nice review, thank you. One thing I like about HKS is that there is no spring under tension when they are loaded. They may sit somewhere for years or decades and will never loose spring tension - there is none.

[@paulmccarter908]

Springs don't lose tension with time, just repetitive springing does that

[@guaporeturns9472]

@@paulmccarter908Yep.

[@آرتمبنعوض]

I didn't want this video to end. Well done man

[@BlackSheepDawnTraining]

I use the comp 1 in triple k pouches I just put a little foam mat peice in the bottom to bring it farther up in the pouch and make it easier tho grab onto

[@seanreid7313]

Simple but wonderful demonstration of these. Thanks for sharing! I guess I'll have to try both for different carry styles

[@RescueEMS]

Thanks for the review. I have a J frame and I am having my wife trained on it. The HK speed loader requires the shooter to remove their hand from the speed loader and then grab the knob and turn to the right to load. This adds another possible hang up for a novice. The Safariland has a no issue loading by pushing the frame (which is where she has her hand already) and rounds are loaded. Either way, you have to practice loading to use both in a stress situation. Also, I recently bought her a soft pouch on Amazon for 2 speed loaders and they are less of a profile than the leather type. Lastly, speed strips are another item to consider, but they are more difficult in a stress situation than the speed loader. To qualify, I carried a revolver as my duty weapon (1980) and had to engage a suspect from behind my patrol car. Had to do a combat reload using speed loaders (HK) and it is the training that carries the day.

[@scottf.3808]

Good compare and testing as I have HKS by default....Good info and vid....Good stuff....

[@SlimCowboy]

Scott F. Glad you liked it

[@Deadly_DoRight]

Nice review Slim. I'm looking forward to my first combat capable revolver soon and reloads are something I'm still working out. Keep up the good work!

[@SlimCowboy]

Deadly_DoRight glad you liked it

[@geohig01]

Excellent points - I use the Speed Bees, which are much more expensive. Like the Junior mints!

[@jessanfernandez2141]

how much speed loader M206 & grips.

[@Narsuitus]

I have been shooting revolvers since the late 1960s. I have never used Safariland or speedloaders. I have only used 38 special and 357 magnum HKS speedloaders. I own three HKS model 10-A speed loaders for my 5-inch 38 special revolver. I own eleven HKS model 27-A speed loaders for my 6-inch 357-magnum revolver. Once, I accidently purchased an HKS 5-shot speedloader. I contacted HKS and Sharon Farris, the HKS sales manager, was very helpful. She replaced my 5-shot speedloader with the correct six-shot speedloader. I only have good things to say about HKS.

[@JacksonWalter735]

Man I'm loving these speedloader comparisons. The HKS are probably my favorite out of the ones I personally have experience with. Sometimes I wish I was an engineer though. I would love to make a speedloader that's a strip with knob on top so that's easy to carry without printing. However, it has magnets (maybe clips?) that quickly and easily allows the strip to roll over and take the shape of a traditional speedloader once those magnets/clips connect together.

[@walkingolga6235]

if you know anybody who draws, ask them to draw a patent!

[@DIYStangsandFreedom]

Thanks for the informative video! I'm a revolver enthusiast , my loadout is 9 speedloader pouches with the HKS speedloaders. From doing multiple reloads, I recommend a bigger pouch like the ones you shown in your video, I don't recommend the HKS pouches because they are so snug and tight.. that it makes it hard to pull out your loader. I guess the one good thing from the HKS pouches is that they are better for Concealed carry

[@whomagoose6897]

The Safariland comp-3 is the one to use for shooting competitions. The comp-3 has a longer handle to get a robust grasp of the speed loader. Safariland makes a speed loader pouch that holds all makes of speed loaders in a open top retainment. Each holder has internal clips to retain the loaders for carry. Both Safariland asnd HKS loaders fit into the Safariland belt holder.

[@PurrsPlace]

Nicely done video! This cleared up any doubts I had and introduced a new idea to me concerning speed-loading (the HKS's jiggle being a benefit). Thanks a bunch, Slim! =)

[@jcools734]

Check 5 star they’re like the HKS but all aluminum, and due too the star shape are less likely to hit the grips! As well they use a counter clockwise turn to release the rounds!

[@russellleavitt4449]

I did select the HKS Speedloader for my new Taurus 856 snub nose revolver. Just because of the better grip of the knob.

[@larrycovolo3577]

That's what the bottom of the carrying case opens up for you open the bottom part too and push your speedloader out instead of trying to pull on the top

[@charliesierra6919]

Great review! Very well filmed so I could really see what was happening. I have those same grips on my Smith and didn't realize they could be a factor, thanks!

[@sanitary103]

Oh snap we cross paths! Hope all is well.

[@charliesierra6919]

@@sanitary103 Ha yes my brother, hope you and the whole Sanitary family are healthy and happy! Small world.

[@russellleavitt4449]

Good review. I am new to double action revolvers and Speedloaders. This was a very informative and helpful video. Thank you.

[@davidsandberg7631]

After watching your video . I went to HKS website and according to what gun model you have some of their loaders do not allow bullet jiggle. Per their web site I have no first hand knowledge. Just looking into what speed loader is best for my needs... Thanks

[@scenicdriveways6708]

I've had issues in the past with the cartridges coming out of the HKS while the speed-loader was in my vest pocket, that's why I no longer use them.

[@rmello381]

Does safariland make a version for 410/45LC ? I cant seem to find it .. ( using it for the judge )

[@bobinlr5055]

The firm hold of Safariland jams on my J-frame or Charter Arms revos, only Zeta6 j-clip work reliably with these small guns. The small knob on the Safariland needs to be larger with some texturing to make the knob easier to grip and rotate when loading. If your gun’s cylinder swing arm gives enough clearance, the Safariland push release is quick and certain under stress, rather than having to rotate a knob, especially if you forget which way to turn it!

[@blueskeleton7744]

What is the best speed loader for a Ruger gp100 wiley clapp 357mag 3"barrel? Also.. not a fan having a belt case to hold the loaders (public will see them and indicate I'm armed) rather have them in pods (6 shot) to carry in my jacket or in front pockets of my jeans or shorts.. I do like the jiggly ones, due to easier loading quicker. Nice video man. Very informative for us revolver owners..

[@SlimCowboy]

Hks work well with my gp100. Look up desantis second six they let the loader ride on top of the belt and don’t print as bad

[@blueskeleton7744]

@@SlimCowboy thanks Slim

[@BigBosley]

I have HKS loaders for my SW 442. I bought them about 10 years ago. When you turn the knob to lock the rounds in they don't rattle like that. They're in there solid. weird, huh?

[@SlimCowboy]

Some HKS rattle, some don’t.

[@chuchuchip]

What models fit a Schofield? Will any model work with a Schofield because of the open cylinder design?

[@Josh47147]

You can add speedbeez to the mix. You gotta use the speedbeez pouch though.

[@jasestrong]

I love the SW 329PD i have the 386 PD , 7 shot 357, great carry gun!

[@jakerook6248]

Speed loader review with Jeff goldbloom voice? ...k I'm in 👍😆

[@user-gl8tv8pb8k]

Very helpful review

[@guaporeturns9472]

Trim a chunk of wood to put on the bottom of the pouch so the Safariland sits up higher and therefore easier to grab

[@tubero37]

If you're going to load wad cutters you better go with the safariland ones because if the rounds wiggle it's very, very hard to put them into the cylinder since wad cutters don't have a tip. I use federal hst and their design is also like a wadcutter since the bullet is flushed with the brass. Just get the safariland since they go with anything.

[@datdudenosense]

Good video thank you very much for the information

[@magnum.357mtb5]

Nice video, I prefer safariland by far , I carried hks in tha past but sometimes a found all my rounds were loose in my pocket , but a couple years ago I started carry 2 speedstrip in a belt pouch is so easy , not bulky and with practice you can reload a revolver fast . One again nice video 👍💪 and happy new year

[@SlimCowboy]

Eduardo Babroff glad you like the video I also sometimes carry speed strips for the same reason

[@Cool95951]

What speedloader work for a webley MK VI cal.455. Other then the pricy prideaux loader? Thx

[@zacharybush3979]

Great video!! Very helpful! Thanks.

[@SlimCowboy]

Glad you liked it

[@JuanMunoz-nq7kv]

Awesome video ! The best !

[@cowtownokla]

Very good "real life" review!

[@michaelschaffer9165]

For a pocketable speedloader check out Revision CV. They have a plastic cover for the bullet noses. You can use the cover or not your choice. They also release the cartridges like a Safariland loader using a pin that contacts the cylinder. Good price too I think.

[@SlimCowboy]

I actually have tried them I do like them. Hoping they expand and make a six shot though because I only have a five shot for my J frame

[@t4texastom587]

Can you please tell me where to get these.... gunstores..... sporting goods stores.....or online?

[@SlimCowboy]

Amazon usually has them also eBay along with most Websites like Brownell‘s and Midway

[@jeffcolwell8459]

Just stumbled onto your video i have the r i a m206 and my wife has the 643cairweight. Which would you prefer

[@UnderPresser]

I like speed loaders. As with anything, 90% of its effectiveness comes from drilling, drilling, drilling.

[@joelsmith9311]

Do the HKS loaders rattle much when they’re in the leather pouch?

[@stormrider9831]

Who is the maker of the speedloader belt carrier?

[@stevocamatcho9266]

Good review bro good job

[@pawpawpimping.8470]

Are those junior mints

[@SlimCowboy]

Yes and they are very refreshing

[@danielvelarde755]

Do you happen to know the advantages on the different lengths knobs on the speed loaders for safariland. I was thinking comp 3 for at home self-defense but wasn't sure because of lack experience and then trying to debate on one or two for Carry for my 3-in king cobra.

[@whomagoose6897]

I use the Safariland Comp-3 loaders for competition. The long handle is great for competition. But, if you have large sized custom grips the handle gets in the way. If you just use factory grips you will have no problems. The advantage of the long handle is there is more surface to grab. During a hectic competition the comp-1 may be too small for larger hands. The Comp-3 eliminates grip problems. There are a lot of ways to hold the loader while twisting the handle to lock the ammo in place. I've seen people flip the loader over to put the bullets on a flat surface. Never worked for me. Some use a Safariland loading tray. I don't behave one. The way I do it is to position all the rounds in the holes like normal. I am right handed so you can just reverse the hands if you are left handed. Keeping the loader up to contain the loose rounds. I put the rounds on my palm just under the joint of the index finger. It's a bony part of the hand. Turn the loader upsidedown on the palm to keep the loose ammo from falling out. Wrap the left hand's fingers around the loader to cup the loader and loose rounds. Use the right hand to twist the knob clockwise as you see it. Locking the rounds in place. My experience with Safariland loaders is strictly with the Comp-3. When pushing on the spring loaded handle you can feel a slight tightening of of the handle internals. It is not much. Press all the way in to include that tightening portion. That's when you know you are sufficiently press in to twist the locking mechanism. The rounds will not fall out if done properly. To release the rounds from all Safariland spring loaders. Press in the star shaped protrusion inside the circle of bullets. This released the pressure holding the bullets in place. Safariland has a special three loader carrier. An open top carrier that is great for maximum speed to reload your revolver for competition. Includes a special internal "U" shaped clip to prevent any unintentional release of rounds from the loader. The Safariland 3-loader carrier pouch will hold all Safariland sizes of loaders, HKS loaders, Pachmayr loaders, Nighthawk/Korth loaders, Speed Beez loaders, and, 5-Star Firearms loaders.

[@crackedfingerz]

Great review. So, what's the deal with that snubby? I've been looking for a speed loader compatible with my S & W 642 Airweight. 5 shot. Mine has a custom grip with a cutaway for better clearance, but I still haven't found the right speedloader. Any recommendations? Thanks.

[@SlimCowboy]

Try the CV reversion ammo pod

[@crackedfingerz]

@@SlimCowboy Thanks!

[@zambonibob2026]

I’m hoping to get my first revolver here soon and this helped, thanks.

[@SlimCowboy]

No problem glad I could help

[@zambonibob2026]

@@SlimCowboy Its funny cause in your video you have a S&W 638 airweight which is exactly what I was looking at buying. What are the odds?

[@konstantino.345]

Good review! Thanks!

[@georgeowens5253]

For the fastest way reloading. Moon clips is the only way!

[@milwaukeegregg]

Good review.........thanks

[@mikoviza5492]

Which one will you recommend on horseback situation?

[@SlimCowboy]

Probably Safari land

[@TheScaleTech]

I really like speedbeez speed loaders but they’re rather big and hard to carry

[@preppercamper2579]

I like that Safari Speed Loader push thanks for turning me onto it .+++ keep with Jesus Christ+++.

[@afnuff1284]

Looking forward to a 7-shot speed loader to come to the market compatible w S&W 686+ L-Frame

[@walden6272]

Don't they have that now?

[@georgeveneziano2754]

All good stuff. But if you change your grips whole other story

[@danielbeck9191]

I think you reversed the names of the speedloaders the first time you used each,=. The Safariland has the black "push-release" knob, and the HKS has the silver "turn-release" knob.

[@silaslongshot941]

Getting the HKS with it's large knob out of a pouch when under the stress of reloading to save your life would be superior, I think, sinse your 'fine motor skills' will be shot because of adrenaline.

[@sanitary103]

Nice review.

[@SlimCowboy]

Thanks

[@NigelRodger-mw8lb]

My safariland comp1 broke after about 5 reloads😐

[@SlimCowboy]

That sucks

[@jmequineservices4766]

Massed ayoob. Dam spell checker

[@wbwills2]

6 & a 1\2 dozen either way

[@williamfagerheim1817]

Regardless, i think cap and ball has a much superior potential.

[@njcranes]

Soooo, you can just put the tip in... interesting

[@bobbarker5884]

Just the tip...wiggle it around a bit 😉

[@manuelmanuel3729]

Don't put the Junior Mints in the speed loaders. I don't think they will be very effective . lol

[@davecooper2303]

May be good, but does not work on a .38 Special Bodyguard.

[@SlimCowboy]

I’m not sure what you’re referring to?

[@petonutt69]

Same problem here, theyre super loose and every video or photo i see is with 357 not .38 special

[@tamiami34]

I had the same problem with my S&W Model 638 Bodyguard. The grip is too wide to easily allow an HKS speed loader to work. It can be done, but it takes way too much fiddling and effort to be a safe and reliable method of loading in a hurry. I replaced the grips with those from my older model 38, which is not +P rated, as they are a little thinner, and do allow the HKS speed loader to work. Then, if I ever carry the old model 38, which now sports the wider grips that came with the model 638 I carry a speed strip.

[@roguefive512]

HKS I prefer on my Model 19

[@yaboicowboi578]

You said “right” way more than you said “knob”…

[@NeostormXLMAX]

safari ones seem far better, in the midst of combat you won't have the timing to slowly screw the thing, instead pushing everything in is faster

[@wbwills2]

Keeler.yep.aluminum.

[@jmequineservices4766]

Kids ... look up mad Aton. He’s old and factually correct. Actual deadly force trainer and cop. He invented some of the stuff cap gun bob is trying to explain. Keep practicing up in your room kid. You might get that dual wielding down yet

[@disdude87]

This dude sounds like Nicholas Cage

[@walden6272]

What? You crazy.

[@Gumby56]

Great video but I will carry that 1911 you have on the table.

[@noizychild]

It's kinda small, might not work as good as you'd like...

[@mitchmaile5979]

The hks🤔 is 1/2 plastic

[@SlimCowboy]

The knob Is aluminum

[@jmequineservices4766]

Since you clearly don’t know how to do this why would you try to demonstrate this for others?

[@chrissizemore745]

u never said what people what to here

[@SlimCowboy]

Which is what?