Configure Cisco Access Point using CLI with WPAv2 Authentication

[@MrTrollHunter]

Thank you very much for this, I had struggled for a long time pulling my hair trying to configure this over the webinterface, but to no avail. This simple little guide was brilliant. Thank you again

[@fred2009ification]

Yo buddy, very cool tutorial. Keep up the good job. Greetings from Brazil!!!

[@NovaCayn]

Holy crap you are awesome. I was having issues with 404 error found in webgui but when I did your step by step, it worked like a charm. Thanks man!

[@itsupportpeople219]

Thanks for watching...

[@FariaAhmed31]

It saved lots of time. nicely explained and very easy to understand thanks for your effort

[@itsupportpeople219]

Thanks for watching

[@Pocketpapi-JP]

thank you for this video. i dont really ever leave comments but you really helped me a lot with my job!

[@Wrexhavik]

Great video!!! it helped me a lot to configure a 3702 LWAP to autonomous. my question is how can you "show" connected clients (and SSID) from CLI? I am doing this all remotely so I cannot get to GUI.

[@juancarloshedz3627]

Niceeeee, thanks dude, i was try to find this configuration, chears

[@ApriantoHarun]

Cheers mate

[@pulemdluli2204]

Thanks Buddy, This extremely helpful.

[@vendorspam1823]

Configuration Question I was curious if you could post the config so we could practice cutting and pasting it? This is an excellent video and is much better than taking a class from Cisco. :) Also, if you have a video that shows how to use a guest vlan in addition to the the one from main users this would also be most helpful. Thank you for sharing and doing a great job.

[@donnicholson3170]

Great tutorial... well done!! Thank you!

[@itsupportpeople219]

Thanks for watching...

[@alltech247]

GOD BLESS YOU ...................AMAZING WORK DONE :)

[@itsupportpeople219]

Thanks for watching

[@peternchlls9]

Great video, thanks mate!

[@krishnam1817]

Good one 👌

[@cloudtopic1681]

Really it helped me a lot... much appreciated

[@itsupportpeople219]

Thanks for watching

[@ОлексійКлименко-д3ы]

This helped me a lot, thanks!

[@itsupportpeople219]

Thanks for watching

[@laprincesaquebusca]

Muchas gracias, excelente explicación que Dios lo bendiga

[@imaneouikhalfan6245]

well explained, thank you very much.

[@aneil2dig]

Great help, thank you :)

[@constantinkwizera9519]

Hello ,I appreciate how you teach And May Gof bless you So how to set Aironet into catalyst C1000

[@muhammadnaseeraziz6888]

thanks, very helpful videos.

[@ranjithsss2004]

Good one bro....could u put one video on what scenario ospf used...

[@itsupportpeople219]

Thanks for watching...

[@TeepuSultan-k9t]

Thankyou brother 💓❤️

[@Lyriks_]

Glad that you upload more regularly, was waiting for this ! Would this command work with some older models ?

[@itsupportpeople219]

Thanks for watching... I reckon it should work and one thing you can do is use the " ? " mark to check the available option for your AP. Thanks

[@quantumtechnology7130]

cisco switch or router is necessary for configuring Cisco Access Point ???

[@bactrimbox]

Great video,

[@itsupportpeople219]

Thanks for watching

[@sirnoble9183]

Really helpful.....Why am I getting different DHCP issued IP every 3seconds to the AP?

[@itsupportpeople219]

Thanks for watching... I think it's a lightweight version AP. Could you tell me the IOS version of your ap. Is ir k9w7 or k9w8.

[@sayyamsaini2597]

Sir, is it neccessory for our computor or laptop should be on same network for taking console or we should used different network like mobile hotspot /wifi.

[@ImranKhan-ci9el]

Console can be connected via serial so initially no IP is needed. Just select the correct comm port.

[@vars-itlearnings7467]

hi bro appreciate your efforts , how to keep same SSID with All the HQ and branch offices with Domain AD Accounts , How to measure the Health of the APS and its provide the correct Speed , any check list that to do before perform upgrared APS firmware or backup of the configurations

[@jerbancoalijerban1744]

Thanks for the great video I am using C9105AXW AP. I think I pressed the Mode Button more than 30 second therefore FIPS mode flag is cleared. It doesn't go on configuration terminal. Have you got idea how to fix the problem.

[@ArshadKhan-fq6cz]

Thanks for your videos. I was just wondering do you know how to configure a cisco 871 ISR as a ethernet switch. So it just expands the ports on a primary isp router.

[@itsupportpeople219]

Thanks for watching... You can watch the following video kzbin.info/www/bejne/qIPKlZ-eiMeWsLc

[@ArshadKhan-fq6cz]

@@itsupportpeople219 Thank you Sir

[@vikaskumarupadhyay2552]

Pp

[@eduardoklubus8319]

hola queria agradecerte por la informacion me sirvio para configurar un 702i muchas gracias

[@connorp8408]

Would it be possible to use an AIR-CAP2702I-B-K9 as an access point/extension to my current ASUS home router, ideally I would NOT have to make it have its own SSID, I would like to keep the current SSID and have the CAP2702I just extend the range of wifi. Thank you

[@kayodeajibade1820]

Which means I can't do any configuration without the Cisco router?

[@kdevkdev1708]

thank you very much.

[@PixelGamer4k]

I already gui configured this but it is showing no internet when I connect it to my mobile wifi........ I don't understand how to configure the modem to Cisco ap..... I don't have any router or switch I have only a home modem......

[@thedigitalgiants3085]

Thanks for your useful video, but for me I get a stack, Am using cisco aironet 3700 series 802 called AIR-CAP3702I-H-K9 in configuration of IP address it goes well but after I can't configure ssid because it says dot11 is invalid and where I try to show ip int brief only get BVI1 and gigabitEthernet0, no Dot11Radio0 and Dot11Radio1 visible as it shown in your video. please may support us on this issue ? #IT_Support_People

[@Faizymr]

I have updated the firmware to a new version, I want to configure the 2.4GHz and 5GHz bands both in one SSID through the CLI. Please assist me with this issue. This model AP: AIR-CAP3702l-A-K9

[@javierfernandezvieyra3931]

my AP is this model cisco air-ap3802i-b-k9 factory reset and the configure terminal comand is not recognized i do not what to do i just want to config the AP with host name, DHCP just to connect to my isp then config a SSID and wifi password

[@mrter2011]

thanks you

[@afriendlynorwegianguy3284]

there where some weirdness on step 3 third command. when i typed ssid taobao(my ssid name) it went on to configuring the ssid. not like what happned in the video where the settings were applied to the ssid. does anyone know why that happends?

[@luisdiegohidalgo394]

I have a 100/100 mbps internet connection but my ap seems to decrease the speed to just 20 mbps. What could be wrong ? I used the gui to configure the WiFi.

[@luisdiegohidalgo394]

Im using wpav2 auth

[@nehabadole2595]

thanks bro

[@naz0079]

I've got a cisco air-cap2702I-E-K9. but I don't have the power cable, do I need it? Thanks

[@itsupportpeople219]

Thanks for watching .... No you don't need power cable only you need a poe injector and an Ethernet cable to power up the AP.

[@quentinblanchet261]

I have an cisco 2600 and i don't have the command dot11 ssid ...

[@textembi4932]

How can disable 5GHz and leave the AP to work only with 2.4GHz?

[@muhammadnaseeraziz6888]

will done

[@itsupportpeople219]

Thanks for watching.

[@ganeshmondal6196]

I request to you please made a video Cisco access point model no.AIR-AP1852I-D-K9 with full configuration .

[@itsupportpeople219]

Thanks for watching...

[@Premreddy-q4m]

Do image upgrade

[@rishabhroy9770]

2.4 GHz , not 4.2 GHz

[@Anamoly_]

2.4 GHz

[@laurensVast]

Step 2 on switch and vlan ap# Enable ap# Conf t ap(config)#Dot11 ssid [SSID_NAAM_1] ap(config-ssid)# Vlan [ID_1] ap(config-ssid)# authentication open ap(config-ssid)# authentication key-management wpa version 2 ap(config-ssid)# wpa-psk ascii ciscopassword ap(config-ssid)# Mbssid Guest-mode ap(config-ssid)# End

[@memetdifa9461]

how to open channel 80mhz cisco air-ap1832i-f-k9

[@leomaredcampos4941]

IT DID NOT WORK MY CISCO AP IS AIR-CAP2702I-A-K9? ITS stupid

[@mrter2011]

my cisco AIR-CAP1702I-E-K9 it work!

[@ronthedon3106]

Mine has root port13 14 and 9

[@ronthedon3106]

Please make it much clearer.. Your losing me loool

[@marcosdxdydz]

everything is wrong

[@coinkiller5495]

Ha bud when you talking SLOW down you talk that fast no one can keep up with you and I just turn over to someone else all you say just rolls into one

[@LemoNopes]

Thank you very much.

[@gajanankshirsagar7186]

Thank you so much