Cooler Master Vertical Graphics Card Holder Kit V3 - Installation Guide

[@disposable_hero1725]

The way I found best when it's just yourself, install the riser cable to the mobo first, then the case bracket and then install the riser cable to the GPU bracket and then mount to case bracket.

[@philipphillipson6178]

The extra room towards the front also does another trick: if your case has bars between the slot covers you normally get into trubble inserting the HDMI/dp cables since the connectirs are upright now. By sliding the vertical stand a few cms, you can thread the cables between the slot bars and connect them without having to cut the slot bars.

[@ChristopherFlannigan]

Good point

[@bachkhoi9450]

Tried it and didn't like it, sliding the vertical stand a few cms make empty space between case and gpu with wire.

[@knightsljx]

@@bachkhoi9450 get a case that allows complete removal of the pci slot covers

[@mattchumoore4214]

​@@bachkhoi9450 buy a 90 degree hdmi or display port cable and it almost mitigates that

[@gustavodugarte4297]

thanks for sharing man

[@martin190865]

loved this video for 2 reasons it was very well explained but best of all it was like listenin to a mate tellin me how to do it. thx

[@villho]

Again, mr Flannigan delivers the best tutorial of PC case hardware!

[@MADHIKER777]

Always the very best explanation of hardware & instalation on KZbin! Even though these are pricy, I think you've convinces me!

[@mkmac909]

JUST FYI. the card doesn't need to hang awkwardly at the final stage, you can slide that bracket forward as instructed and then place the card into the bracket and secure in place with the quick release tabs. once the card is supported, finish plugging into the slot.

[@careditor]

I will be installing new 4070 CM holder today. Thanks mate for this video.

[@ICmikeyP]

Man you gotta show us this in a mATX case because I think people going for this one are really looking to put it in a smaller case because it's literally the only Vertical GPU mount that fits in a mATX case. A define 7 mini or Meshify 2 mini would be greatly appreciated to see this in.

[@TheOnlyLeader53]

yeah u r definitely right about that. Why would bother having this piece for e-atx cases already when i can give 50 € more and buy a totally new e-atx case? They should have used a m-atx case as you said.

[@MoltenKing992]

Somewhat agree. In my matx, the 3080ti sits less than a bottle cap from the psu and hdd shroud in a cooler master mb320L case. But in my atx, the space between the shroud and the gpu is so much that the case looks empty with the horizontally installed

[@LatinaOtaku]

I just got one in white because it was on sale for Cyber Monday. It would be my first time vertically mounting a GPU as well I was originally going to get the Lian li one too. But I like that you can move this one.

[@mrobinson8686]

How Much did you pay?

[@LatinaOtaku]

@@mrobinson8686 50 or almost 60 can't remember

[@sanfran49rs]

Thank you for this video! Made my pc build easier ❤

[@rmorenberg]

Always great details

[@K_24_]

Great tutorial, thanks! Just purchased this mount due to the CableMod adapter fiasco.

[@ResetXPDR]

Excellent instructions. Will use this when my kit arrives this week. Thanks!

[@Darkknight9035]

Does the pcie click when inserting the gpu? Mine doesn't click no matter how hard press.

[@seanlowe7443]

Is it possible to have a NIC or something plugged into the second or third PCI-E slots behind this bracket? Only thing holding me back from getting one right now

[@HOBOTw1tcH]

You can slide the GPU a good distance away from the mobo. As long as you have enough room in your case. Also depends on how tall the pci-e slot item is

[@marinipersonal]

Very clever design. Full adjustable. Just a shame the Purple strip.

[@ChristopherFlannigan]

I thought the same when I opened it, but you can't see it once the gpu is in

[@withmygoodeyeclosed]

The strip is gray on my V3 mount.

[@domeberlin4480]

@@withmygoodeyeclosed jeah we have the new mount

[@HOBOTw1tcH]

I thought the purple was kinda cool. Figured he ordered that one. Not sure why they’d do that unless you asked for it. The cable is grey/white on the white mount that I just got

[@Sparky_007]

Is there ANY vertical mounts that don't kill the ability for you to use some of your PCI slots for OTHER devices if the case doesn't have some dedicated opening for the GPU above?

[@bryandixon2570]

Im hoping the link i provided does the trick.. i plan to order it this week.

[@BucifalulR]

@@bryandixon2570What link :)?

[@bryandixon2570]

@BucifalulR hmm it must have gotten removed. Let me find it again

[@BucifalulR]

@@bryandixon2570 sure :) thank you. EDIT: or the name of the product would do

[@bryandixon2570]

@@BucifalulR EZDIY-FAB PCIe 4.0 GPU Mount Bracket

[@philippbusch764]

As always very informative video! Unfortunately I couldn’t get a V3 with the purple cable. Seems they produce it only with a grey one now😢

[@el_carlangas_xd6449]

I have a question I can use this vertical support In my lian li 011 dynamic MINI

[@suunnny1296]

I have the same question, have you tried it out and does it work?

[@robipindric7654]

The only issue i have with this mount is that it slides forward when you try to plug in display port cable or HDMI cable. It looks like those two closing clips are not tight enough. At first i thought there are some extra screws that i forgot but i didn't see anything in instructions.

[@JosePto]

Does it block airflow for cards like 3060Ti FEs? These are small and I feel this mount would block the airflow for the fan blowing through the card.

[@fuggly-qg9on]

your mom blocks airflow

[@Diabrorojo]

​@@fuggly-qg9on😂

[@josephesprada2642]

Hello Sir MSI RTX 4070 ti SUPREME X 3 SLOT Can i use this bracket right?

[@ivananisimov3121]

+1 ?

[@mezz1-dll]

MAXIMUN 3 SLOT

[@applemonkey7305]

Wonder which vertical GPU mount is good for rtx 4090 in a fractal torrent case with noctua dh15 cooler

[@AndreasRP.]

not this one, I bought it and now I have to get slim 140mm fans for the bottom part of the case because this mount can fit in otherwise, and I cant move it up because then it will hit the cpu cooler

[@vladislavvasilev231]

is there enough room to plug in the thick usb and audio cables for the front panel? Probably not !? OR? Compromise again?

[@jamesthom6701]

How far over does the mount push the gpu? I've got a rog strix 2070 super that i am trying to fit into my fractal define c mini. The case has a max length of of 340mm for the gpu, and the gpu is about 300mm already. So I've been trying to find out how much it moves it over. This seems to be the only mount that works in matx cases so i hope it'll work! Its just alot of money to spend without being 100% sure it will work!

[@ideabagja]

have you found the answer for this?

[@toonnut1]

Wow £77 that's way more than the last coolermaster vertical mount I bought

[@ChristopherFlannigan]

Everything has gone up in price. It's gen 4 and the bracket is in two parts so I can see where the money goes

[@knightsljx]

Gen 4 risers are super expensive. CM is basically giving away the bracket itself

[@anone3842]

Worse than that for me. The only place selling it is Amazon third party and they charge 33 EURO for postage (stealth charge) so it ends up being EUR 114,80 at least!!

[@toonnut1]

Mine finally arrived today from amazon uk I paid £53.62 much more reasonable price

[@fuggly-qg9on]

@@anone3842 I've seen them for 60 euro on amazon, this exact model...

[@bantcliff]

Will this fit in the top 6 expansion slots instead of the bottom 6? I have a bottom Fan that I'd like to keep if possible so extra slot higher should allow it to fit underneath.

[@the0netruth]

I have 2 questions:- 1.) I have 5000D Corsair airflow case and it has PSU cage roof where a riser cable can be mounted, do i really need to add bracket? or i can just simply mount riser cable on my PSU cage and done with it. 2.) Does it support Asus TUF 4090 card and it's weight? The site doesn't mention GPU and yes i know PCIE 4.0 is my GPU and this bracket but the bandwidth that 4090 pulls will it work and safer? I had terrbile experience with Cooler Master PSU that's why i am hesitant with this company.

[@ToniRawGazer]

What do you recommend for the gpu to stop leaning forward

[@HAMED_B]

perfect as always.

[@PlutoKam]

Coolermaster are a great brand

[@EdsonSouza051]

Parabéns pelo vídeo o único que explicou tudo sobre o suporte! ✅ 🇧🇷

[@yalnizkalpler]

Hi friend,Does this kit increase the temperature of the graphics card? The horizontal position of the xfx merc 6900xt I have is 70 degrees

[@Manuzoka1996]

Does it work with a mini ATX, 4 slots?

[@LutraSGM]

Hi Christopher, I hope this question find you Can you help answer where does the weight of GPU press down onto, is it the bracket that helps holding the GPU (usualy on the left with the metal plate of the GPU), or the PCI slot of the GPU (I heard Gigabyte PCI one is very flimsy and weak) that connects to the Riser cable (which I want to know before doing any vertical mount bcuz idk if it could also harm the GPU PCI slot or crack it due to the GPU's weight itself) I really appreciate any insight or experience about this, thank you ❤

[@skynetintex5878]

Does anybody know what clearance you have at the bottom, e.g. from the base of the Cooler Master holder to the base of the case? I have a Phanteks NV7 and can't quite work out what's available. I intend on having a GPU water block, so need some guidance to work out the loop runs.

[@wolf1980reed]

Great video, nice small footprint in the case, will this mount work in the Lian Li O11D EVO XL?

[@carolinanumber1830]

Will this fit in a NZXT Flow 5 case or is it going to block off all the lower slots etc?

[@artvandelay6306]

It definitely seems crooked toward the bottom of where the two pieces meet at the back, on mine. Seems like yours fits similarly. Card seems level, though. Very odd.

[@javedkod]

is it compatible with the 4070 ti?

[@nabiljemel2838]

I think this might also be a good solution for HTPC desktop cases that are not wide (high) enough to host these new behemoth graphic cards, I wish I did know about this solution prior to upgrading to a completely new case.

[@anone3842]

I just paid over 600 EURO for latest Coolermaster 700EVO case and it ONLY INCLUDED THE V2 VERTICAL BRACKET and that is absolutely shit bracket for the 4080 card I have. Will not hold straight and ribbon absolutely straining the slots on motherboard and GPU... it needed the forward/back movement to move GPU out from motherboard. Sickening that they only include V2 mount in a 600+ EURO case that I only got this month in December.

[@RIVERSTX_]

I’m curious about fitment with o11d with 3 bottom fans

[@welshinu]

i have version 2 3 fans no problem ver 3 should be fine youtube my name have a short video on there showing in o11d with mesh front and side panels 😁

[@bachkhoi9450]

@@welshinu thank you

[@Yamagatabr]

@@welshinu do you ha eany idea if iw works with a O11D Evo?

[@welshinu]

@@Yamagatabr No sorry have a look on the web site at the dimensions of both cases if they are the same on the bottom then i guess your good to go 👍👍

[@Yamagatabr]

@@welshinu Thanks! Will do

[@gamer4life518]

Is this vertikal gpu ready to deal in a Lian li o11 dynamic evo? (My englisch is not the yellow from the egg, but i hope you understand:^)

[@petmey5281]

Seams with the accessory rendering your pcie expansion slots unusable, It would make more sense to use an ITX or micro ATX motherboard with this GPU holder

[@lindseyhunt1090garageb]

Just got mint today. I can finally put my side case glass on lol. 4090 runs 10c hotter but its still only 71c

[@Drewtheelder]

Well explained, thanks.

[@jim-q1m]

can the vertical gpu bracket support 2 slot video and a 3 slot video card ,, i bought the new rtx 4080 super 3 slot video card , trying to side mount my video card

[@rcmanrc2453]

nice video. wonder vertical mounting will it lowered GPU tempurature?

[@ChristopherFlannigan]

In some cases yes in others it makes it worse

[@Oracleman1]

How much does it add to the total GPU assembly length?

[@arksurvivalevolved9190]

So that means we can not use other cards on the slots?

[@thiagopassos4325]

can you tell me if this support is compatible with the cooler master h500p mesh case? i have a 4080 wanting to put it vertically

[@WowItsJau]

Anyone know if this clears the bottom two expansion slots on a regular ATX/EATX case if I use it in MATX mode?

[@nflikt]

For some reason mine doesn't sit perfectly straight. It angles slightly towards the glass which is annoying. Also increased temps while gaming from around 50C to around 60C but its still within acceptable levels. If i had a choice i wouldn't of vertically mounted it but because of the Cablemod adapter recalled i had no choice. 40 series GPU's are way too big. I have a 011D XL and my Aorus Master 4080 makes the case looks small.

[@jedi481bbx4]

is this better than the nzxt vertical gpu mounting kit?

[@lordknightseyren]

Is this fit on a Micro ATX (mATX) case?

[@HAMED_B]

I have a question. is it possible to use this GPU holder in order to provide enough space and install case fans beneath the GPU. tnx.

[@robipindric7654]

In my case yes. More than enough. I have H9 Flow case.

[@Pragy]

Will this fit in a Gamdias Talos E3 case?

[@ibrahimcivanoglu2758]

3:20 Those teeth on the left side prevent this from being installed on the SL600M, which is a Cooler Master case. Unbelievable.

[@zethcrane5468]

hi, will this fit in 5 slot PCI casing? around 12mm in height..

[@Kartunga]

What’s with sagging ? I have a 7900 XTX , does it hold it straight ?

[@OLDUSAFMedic]

I would like to do this but my case is too big. That cable won't reach and turn 90 degrees like my motherboard is situated.

[@PinnedOut90]

Would this work with a XFX MERC310 Radeon RX 7900 XTX in a Cooler Master MasterBox TD500 Mesh with a aio

[@jackysss]

Hello, this vertical slot v3, take 6slot of the back bracket? I notice that the v2 takes 7 slot

[@jamesebelegallaher471]

Thank you so much

[@むさし_XIX]

How much is the offset of the gpu toward the front of the case if the card holder is set to the minimum (to the left) ?

[@G.L.R.K]

You mean the gap? Guess it depends on how big your case and the graphics card are.

[@danielcardoso2286]

@@G.L.R.K Hi! He mean about the size that the bracket take when fully retracted, i have the same question about it: My case fit 330mm GPU max size, the GPU is 307mm... would this bracket fit in 23mm (2.3cm) space?!?! Thanks

[@abrahamnava5255]

Nice, works with Corsair 4000D?

[@hkbaxxter]

u ended up doing a vertical mount? if so are temps ok?

[@abrahamnava5255]

@hkbaxxter yep, it only increased like 3°C i bought the Cooler Master Riser Cable.

[@hkbaxxter]

@@abrahamnava5255 thanks for answer! enjoy your build :)

[@LuqmanHakimmm]

Nice vid man! What case is dat

[@ChristopherFlannigan]

Masterbox 520 mesh

[@Relic119]

Anyone use this in a o11D mini? I know that case has a mount but I don’t like the shelf in it

[@iRabTV1]

Just putting this out there that this mount is NOT compatible with the NZXT H510i. I learned this the hard way and people suggested to cut off the metal bars at the back which block access to the Display and HDMI Ports on the GPU. Seriously, why should I essentially destroy part my case with power tools to install the product? I found no mention of this when looking around the reviews for the product so you can imagine my annoyance after spending £75 on it. Looks like I can either return it or buy a compatible case which will cost me at least £200+. Not happy at all.

[@colton9841]

Hello - Curious where you were able to get this from? Although I can find it in black at some retailers, I can't find the white for sale and neither on CM actual store page.

[@HOBOTw1tcH]

Amazon. Just bought a white one.

[@acloudonthebluestsky9687]

really curious this with my Jonsbo D31 cause its small af to me lol

[@Johan-rm6ec]

Does the pcie not need some power

[@mkatakm]

Since it partially obstructs the back of the card, how does it affect the gpu thermals?

[@robipindric7654]

In my case it actually made temperatures better by a few degrees. I have PNY 4090 if that's of any importance

[@nflikt]

Mine increase by about 10 degrees C while gaming. Probably because it no longer had my 3 bottom fans blowing on it. Bit of a shame but im still only reaching 60C which i feel is OK.

[@ANDREIJOBHERNANDEZ-t1f]

Question is it compatible to my pc cas keytech t1000

[@diyet99]

can use at case corsair 5000D?

[@pcjunkie939]

Do it fit on a Bequiet 802 case?

[@Theorcman2008]

Why would they stick a purple wire cover on it? I get it's coolermaster but they could have left it black for people with different color schemes in their pcs.

[@mrST0GGY_is_sigma]

Isn’t it going to be hidden ultimately? Be cool if it was all one color, but they do have to leave their mark..

[@Theorcman2008]

@@mrST0GGY_is_sigma it fucking says coolermaster on the packaging....

[@mrST0GGY_is_sigma]

@@Theorcman2008 doesn’t every brand have their name on the packaging? Sheesh. If it bugs you that much get a diff brand or buy a separate riser cable.

[@Theorcman2008]

@@mrST0GGY_is_sigma That's my point. They don't need to leave their mark IN MY COMPUTER, they already have it on the packaging.

[@mrST0GGY_is_sigma]

@@Theorcman2008 that’s an easy fix, get a different brand.

[@Darkknight9035]

Don't get this if you're using an aftermarket air cooler, it won't fit and even if it does the heatsink will be sitting on the gpu's metal backplate which will most likely melt the casting over time... Funny how no reviewers mention this and I had to find it the hard way, useless reviewers...

[@Eusebiugh]

Can someone guide me how to mount this kit on lian li o11 d evo xl?

This only makes sense if you have nice rgb fans on the gpu, like gigabytes 4090. Otherwise it does not look good in my little opinion.

[@ringoooringooo2190]

Can i use this on NZXT H 510 Flow????

[@Tech-Neekz]

Does this work on matx cases

[@ramzidaone4577]

What would be interesting if you did a sleeper computer with a old tower case

[@JonasJensen1308]

why is there no coolermaster logo printed on yours?

[@ryand7301]

Can it fit in the nzxt h7 casing?

[@_BioX]

What case is this in?

[@cleanprestige74valetingdet13]

Avez vous remarqué une perte de qualité graphique en hdr ?

[@silfrido1768]

I would do it this way but the way this 4090 is set up… he’s a big boy 😂

[@jesusfreakster101]

Will this work with Y60?

[@Macncheese48]

good for NZXT H510?

[@theopszone6775]

Shame there's no bracket that tilts, like the cosmos 700m.

[@dustinclark8946]

Tried this with aorus 4090 master.... Serious sag

[@fuggly-qg9on]

skill issue, also: your mom got serious sag

[@Diabrorojo]

​@@fuggly-qg9onfor doing such a not well designed buoy like him 😂

[@nichovillaruel2364]

It says matx case compatible but matx case uses 4slots on PCIE and you used 6slots

[@kellen4854]

U can remove the top two on the bracket

[@MP-wy3hp]

Anyone know if this will work with the Corsair 7000x?

[@boot_.]

hey, I'm using this but in the 4000d airflow. Is it normal for the mount to "tilt" before I put the gpu in like how yours was b4 u put the gpu in?

[@panterino]

Unfortunately, mine didn’t fit with a Noctua air cooler.

[@ardorcallow4761]

The NH-15 cpu cooler?

[@panterino]

@@ardorcallow4761 Yes, in a Corsair 4000X

[@user-hj4wc4cn9c]

What is ur gpu

[@panterino]

3080 Ti@@user-hj4wc4cn9c

[@undetected426]

I'm 100% upgrading for this i have Cooler Master V2 PCIE 4.0 because of this vertical mount rat can easily enter inside of my PC because of the single opening under the vertical mount im so angry about this v2 thats why im upgrading to V3

[@berserkberserk997]

this is nice, too bad the fuckin strix has the open vents on the top side to push hot air out, with this mount the hot air will end on the mobo. ok ok, 3 front fans should do the job of pushing the hot air away but if u have the card in you hands u know how much heat is coming out from that gap. im not sure if im going to get the vertical mount... this doubt kills me ...

[@FTWGame0N]

In normal posotion most cards will eject the hot air from the fins directly onto the motherboard anyway.

[@berserkberserk997]

@@FTWGame0N also my ssd nvme suffer from this.

[@fuggly-qg9on]

@@berserkberserk997 sucks to be you.

[@CrusaderKnight-y6g]

Didn’t fit in my pc case 😭😭 tried to put it back my pc wouldn’t show any signal so my mum told me to turn it off and back on again and it worked 😢