Developer Kyocera TASKalfa 3500i 3501i 4500i 4501i 5500i 5501i ERROR c7101 c7241 c7251

[@tapiwanasheshoko]

Hey. My Kyocera 3050ci has code error F248. Please help, how do l clear this one? (Only pops up when l print from my pdf reader 🤷🏿‍♂️)

[@MrRicoh]

When printing on Kyocera, UTAX, Triumph-Adler and OLIVETTI devices, the printing may sometimes stop and generate the F-248 error. In experience, if such a situation occurs, it is caused by trying to print directly from a website or e-mail. This is a font error that can very rarely occur while blocking the device. First of all, check in the print queue which job caused the error. We can easily verify it in the device's menu in the STATUS / JOB CLEAR option in the PRINT JOB STATUS tab. This will be the first job on the list. Note that deleting this work will not solve the problem. Due to the constant and very rapid development of technology, you should contact the service and update the firmware of the device, the so-called FIRMWARE. From practice, it is also a good idea to download a document from the Internet to your computer and print it directly from your PC or laptop. 🔥🔥 KZbin SUPPORT: kzbin.info/door/OHtXTtGHj33pUm8Gf2FH3Ajoin

[@piotrg7864]

Witam. Czy podczas wymiany zespołu dewelopera na nowy trzeba aktywować go jakimś kodem? Będę lada moment wymieniał zestaw serwisowy i wiem że bęben i transfer trzeba, ale co z developerem? Proszę o wskazówkę. Pozdrawiam, Piotr

[@MrRicoh]

Witam, tak trezba go aktywować, proszę uważnie obejrzeć ten film tu jest wszystko po kolei pokazane KYOCERA TaskAlfa 3500i 4500i 5500i Bęben Transfer Deweloper Fuser PRZEWODNIK kzbin.info/www/bejne/hobEhmmqatmieLs

[@piotrg7864]

@@MrRicoh Oglądałem wskazaną prezentację już wcześniej, ale bez dźwięku. W 20 minucie jest informacja że wymiana zespołu dewelopera polega wyłącznie na włożeniu nowego. Nie ma wzmianki o kodzie symulacji. Dlatego też zadałem o to pytanie.

[@MrRicoh]

Wejdź w tryb serwisowy 10871087 potem U130 i tam jest inicjalizacja

[@حولالعالم-ذ1ك]

kzbin.info/www/bejne/q3TGZWOEdstgnbM

[@rhemaofgod2344]

Pls my triumph Adler 2500ci is adding toner and printing dark documents. What can I do. I was told is the toner I bought and I need to change the developer

[@MrRicoh]

The repair must start with the replacement of the Developing Unit and the original toner.

[@peterdindah9978]

Hi my 2500ci di photocopier shows machine failure c3800 code any help

[@MrRicoh]

Remedy: 1 Checking the FFC The FFC is not properly connected, or it is faulty. Reconnect the following FFC. When the FFC terminals are peeled off or deformed or the FFC is broken, replace the FFC.• CCD PWB - Engine PWB Electrical Diagram of PWBs 2 Replacing the ISU The CCD PWB is faulty. Replace the ISU and then execute U411. ISU Replacement 3 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Engine PWB Replacement

[@peterdindah9978]

@@MrRicoh what is FFC, PWB, ICU and CCD full meaning please

[@elsongentil8792]

I have a TASKalfa 5500i kyocera your code is FC050, and other print out with a side deleted. can you help me please.?

[@MrRicoh]

Unfortunately, I have never heard of the FC050 in a Kyocera copier.

[@zalerojo1639]

Mon kyocera 3500i il ma écrit toujours vérifié le bac de récupération de toner

[@MrRicoh]

This is a very strange message. Change the language to English and write me this message urgently, please. Then I'll know exactly how to fix your copier.

[@anilscorner3960]

my kyocera 4500 i top feeder stopped working i can not scan or make copy through top feeder i am scanning from below need to scan one by one how to fix it

[@MrRicoh]

You need to reset options 10871087 and then U906

[@MrRicoh]

@@ساهلوبنين-ت9ل I am very happy that I could help you. Greetings from Poland. Części do kopiarek www.copy-expert.pl/ Facebook: facebook.com/Copy-Expert-113431678801597/ Części używane www.copy-expert.com/

[@charlesbenitezdatwin7623]

@@MrRicoh can you please help me, my kyocera taskalfa 5500i got a problem improper place of waste toner box.

[@adilihsan9366]

i have 4501i machine and its copy is blur and light any solution plz !

[@MrRicoh]

Enter the counter of the copier. 🔥🔥 Get access to support bonuses KZbin MEMBERSHIP: kzbin.info/door/OHtXTtGHj33pUm8Gf2FH3Ajoin

[@Charan-Cabinet2]

I am facing c 2211 machine failure error in 4500i taskalfa Please make a video for me

[@MrRicoh]

Video is not necessary. Replace the drum unit and everything will be fine/

[@peterdindah9978]

what is FFC, PWB, ICU full meaning please

[@MrRicoh]

Hi, That's a good question. An FFC is a type of low flat wire that connects PCBs. PWB is the name of an integrated circuit board. ICU you microprocessor Greetings.

[@mbayediagne7209]

Plateau interne est pleine Comment résoudre ce problème Svp

[@MrRicoh]

Vérifiez le capteur de sortie.

[@ghulamali873]

how to sold light printing problum in taskalfa 6501

[@MrRicoh]

You probably have a used review kit (Drum, Developer, Transfer) then you need to replace it.

[@حولالعالم-ذ1ك]

kzbin.info/www/bejne/q3TGZWOEdstgnbM

[@ft-sx5nb]

i have taskalfa 5500i error code ...jam 0000 but no paper in machine plzz help me

[@MrRicoh]

I do not know this problem, but here is an interesting discussion for you: www.copytechnet.com/forums/kyocera-mita-copystar/86054-taskalfa-3500i-jam-0000-a.html Greetings from Poland Części do kopiarek www.copy-expert.pl/ Facebook: facebook.com/Copy-Expert-113431678801597/ Części używane www.copy-expert.com/

[@andrewfriend4908]

Sound like you have a bad sensor or a spring feel off an actuator or a very small piece of paper you can't find ! Good luck

[@حولالعالم-ذ1ك]

kzbin.info/www/bejne/q3TGZWOEdstgnbM

[@احمدمحمدابوالمجد-ح3ط]

How laser cleaners pleaz kyocera 5500i

[@MrRicoh]

Hi. I don't have a movie about it. You do not clean the laser in this copier. You can wash the outer lens of the laser. Remove the top covers where the paper comes out and look for the laser.

[@rifaqatkhaliq2999]

please guide for c7460 error

[@MrRicoh]

hello, Developer shutter locked - open front cover and slide the developer shutter to open/unlock, restart the machine. The shutter is locked to prevent developer spilling when transporting the machine.

[@abdulkhaliq5685]

@@MrRicoh hy.sir pls your whatsapp no

[@civiltrend4712]

i need a guide to solve problem c7460 please , can you help me @@MrRicoh

[@donaldhunt4]

@@civiltrend4712 Did you ever figure it out?

[@muhammadsiddiqe5553]

Photocopy results are bad plz help me

[@MrRicoh]

What does it mean? Write me more details. Are the copies dirty, light, have stripes or lines?

[@muhammadsiddiqe5553]

@@MrRicoh yes sir copies is dirty lights

[@MrRicoh]

What is the copier counter and what are the drum unit, developer unit counters?

[@muhammadkamran5058]

kycoera 5500i code error 7301 Solution?

[@MrRicoh]

Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Toner hopper motor and front PWB (YC5) Front PWB (YC3) and engine PWB (YC7) Defective drive transmission system of motor. Check if the gears rotate smoothly. If not, grease the bushes and gears. Check for broken gears and replace if any. Defective toner hopper sensor. Replace the toner hopper sensor. Defective toner hopper motor. Replace the toner hopper motor. Defective engine PWB. Replace the engine PWB and check for correct operation.

[@حولالعالم-ذ1ك]

kzbin.info/www/bejne/q3TGZWOEdstgnbM

[@ahmadfarid2834]

How to solve (Error code of C7101 ) Kycera Task Alpha 6500i

[@MrRicoh]

Reinstalling the developer unit The developer unit is not properly installed. Reinstall developer unit BK so that the connector firmly connects. Developer Unit Replacement

[@حولالعالم-ذ1ك]

kzbin.info/www/bejne/q3TGZWOEdstgnbM

[@alhaqq310]

5303 error solution please !

[@MrRicoh]

Causes: Poor contact in the connector terminals. Defective cleaning lamp M. Defective PWB. Remedy: Poor contact in the connector terminals. Check the connection of connector YC7 on the sub front PWB and the connector of the drum unit M, and the continuity across the connector terminals. Repair or replace if necessary. Defective cleaning lamp M. Replace the drum unit M. Defective PWB. Replace the sub front PWB or engine PWB and check for correct operation.

[@حولالعالم-ذ1ك]

kzbin.info/www/bejne/q3TGZWOEdstgnbM

[@izharmujeeb7206]

How to solve taskalfa 4501i c7301 error

[@MrRicoh]

Intermediate toner hopper toner feed error • Black toner is not fed in the intermediate toner hopper in the black toner developer from the black toner container within the predetermined period.

[@thaonguyet9683]

Kyocera Taskafla 3510i with code error C0640

[@MrRicoh]

Hi, defective hard disk. Run U024 (HDD formatting) without turning the power off to initialize the hard disk. Replace the hard disk drive and check for correct operation if the problem is still detected after initialization.

[@naseemullah5913]

Check this vadio inshaallah solve your problem kzbin.info/www/bejne/n4iZoaCvd9KEjdE

[@سبحانالله-ش4ب1خ]

kyocera taskalfa 3050 ci with code error 7104

[@MrRicoh]

C7104 T/C sensor Y error Object: Color models Causes: For the specified value of the initial toner stored in the EEPROM of the developer unit, the output value of the T/C sensor is out of the range between +100 (undetection toner) and -1000 (Coming off of the sensor connector). And that status was detected 3 times continuously. Remedy: 1 Reinstalling the developer unit The developer unit is not properly installed. Reinstall developer unit Y so that the connector firmly connects. Developer Unit Replacement 2 Checking the wire The wire is not properly connected or is faulty. Reinsert the following wire connectors, and replace the wires when they have no continuity. • Drum/developer relay PWB - Feed image PWB • Feed image PWB - Engine PWB Electrical Diagram of PWBs 3 Replacing the drive gear The drive gear for developer unit Y is damaged. (The spiral is not rotated.) Replace the drive gear for developer unit Y. 4 Developer unit replacement Developer unit Y (T/C sensor Y) is faulty. Replace the developer unit Y. Developer Unit Replacement 5 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Upgrade 6 Replacing the drum/developer relay PWB The drum/developer relay PWB is faulty. Replace the drum/developer relay PWB. Drum/ Developer Relay PWB Replacement 7 Replacing the feed image PWB The feed image PWB is faulty. Replace the feed image PWB. 8 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Engine PWB Replacement Części do kopiarek www.copy-expert.pl/ Facebook: facebook.com/Copy-Expert-113431678801597/ Części używane www.copy-expert.com/ Serwis kopiarek Ricoh Warszawa sprintprintserwis.pl/ Utylizacja kopiarek www.oddajelektrosmieci.pl/

[@سبحانالله-ش4ب1خ]

@@MrRicoh thanks for help

[@MrRicoh]

Welcom :)

[@sachinchaurasia8945]

C6020 error kyocera taskalfa 3010i

[@MrRicoh]

Description Abnormally high fuser thermistor center temperature Fuser thermistor 2 is detected 230°C/ 446°F or more for 40 ms. Causes Installation defectiveness on fuser thermistor 2. Defective fuser thermistor 2. Defective engine PWB. Remedy Installation defectiveness on fuser thermistor 2. Check the mounting state of the fuser thermistor 2. If any problem is found, repair it. Defective fuser thermistor 2. Replace the fuser thermistor 2. Defective engine PWB. Replace the engine PWB and check for correct operation. Części do kopiarek www.copy-expert.pl/ Facebook: facebook.com/Copy-Expert-113431678801597/ Części używane www.copy-expert.com/

[@anirutrattanapan7769]

ขึ้นc7911คับ

[@MrRicoh]

Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Developer unit and front PWB (YC7) Front PWB (YC2) and engine PWB (YC8) Defective developer unit. Replace the developer unit.