Can’t believe 2 years later this is still the only install video for the stinger
@FordExplorer74482 жыл бұрын
My cpi kit should be here today along with a bms intercooler. Thanks for the video.
@stinger_gt2192 жыл бұрын
You’re welcome bro
@alexreyes69072 жыл бұрын
Good stuff man, been following your build! Don’t have CPI yet but my JB4 just came in, so it’s a start.
@stinger_gt2192 жыл бұрын
Trust me. The jb4 will wake the beast up 🙏🏽😈
@dailydriventuners91222 жыл бұрын
wish my mishimoto charge pipe was already tapped. i like how with bms it sits at the bottom where mine will be sitting on top, coming in this week.
@BigD45622 жыл бұрын
Wished you had this video out a few months ago lol. Thanks for the video man.
@matthewwarner31302 жыл бұрын
what fuse are u using
@Daarken1st2 жыл бұрын
I can’t wait till you post a run with the CPI Kit.
@stinger_gt2192 жыл бұрын
Soon brotha
@djerickd_official2 жыл бұрын
Thanks for this, installed mine last night
@stinger_gt2192 жыл бұрын
Glad I could help brotha 🙏🏽
@D_Rok80 Жыл бұрын
I visited a new Shell gas station near my house today and noticed they have E85. I've been interested in trying ethanol for a while, but I couldn't find a gas station that offers it until now. Today, I started researching what I need to make this switch, and I came across the recommendation to use the BMS flex fuel kit. I also watched your video and learned about the CPI kit. Additionally, I noticed you have a BMS intercooler, which I was planning to install as my next modification until today. Now, I'm unsure about the order in which to proceed with these mods, considering I can only do one right now without my wife giving me grief My current mods: JB4, CIA's, MBRP exhaust, etc. I'm torn between getting the flex fuel kit first, then the intercooler, and eventually the CPI kit. Alternatively, should I prioritize the intercooler first, followed by the flex fuel kit, and then the CPI kit? Thoughts
@zd77777 Жыл бұрын
First start running the flex fuel kit, start with Map3. You can also use Map4 with it. Use a 30% E85 blend, factoring in the 10% ethanol already in most pump gas. After that, i’d recommend doing the CPI kit, as it’ll allow you to really utilize the E85, producing more boost. Then, install the intercooler to reduce heat soak. Hope this helps :)
@lesterpickford64512 жыл бұрын
Man I’m such a visual person when it comes to this stuff so thanks for the video. What if I don’t have the BMS intercooler - where would I connect the flex fuel it and the CPI line to then?
@stinger_gt2192 жыл бұрын
I’m sure they sell an adapter like the WMI kit
@lesterpickford64512 жыл бұрын
Yeah you might be right. I’ll look into that. After I’m done with exhaust I’m definitely wanting this to be my next mod.
@stinger_gt2192 жыл бұрын
@@lesterpickford6451 car really moves with this 🙏🏽
@brian32552 жыл бұрын
BMS charge pipe on there intercoolerd come with the bung for the 1/8" NPT nozzle. I have the Mishimoto intercooler is drilling and taping a 1/8" NPT port the only way to go or does MISHIMOTO make a charge pipe with it built for cpi nozzle already?
@sttng3.3r_682 жыл бұрын
Hell yeah! Thank for the vid!
@stinger_gt2192 жыл бұрын
🙏🏽🙏🏽
@prvideos8229 Жыл бұрын
What location do use for the jsb power connection in fuse box? I know your running like your own fuse box but if your not what stock location you use?
@stinger_gt219 Жыл бұрын
Send me a DM on IG
@DavidDaniel-si5mu2 жыл бұрын
Great video! My question is, did you have to drill a hole into your CP, or did the BMS intercooler already come with that space?
@stinger_gt2192 жыл бұрын
BMS already comes with that bro
@wlfpire2 жыл бұрын
CPI is da way 🍊
@stinger_gt2192 жыл бұрын
Yes sirrrr
@brian32552 жыл бұрын
How easy was it to disconnect the fuel line from the FLEX FUEL SENSOR toward the CPI "TAdapter? Any special too needed here? I'm adding the CPI "T Adapter" TO the FLEX Fuel Sensor like you did because I installed the FLEX Fuel kit way before
@stinger_gt2192 жыл бұрын
Pretty straight forward. Have you disconnected the fuel line before?
@brian32552 жыл бұрын
@@stinger_gt219 no
@brian32552 жыл бұрын
Someone else originally installed my FUEL IT Kit. I'll be installing the CPI KIT this weekend myself So half of it is already done
@stinger_gt2192 жыл бұрын
@@brian3255 it’s very easy tbh. If you need help. Just FaceTime me on Instagram
@json2162 жыл бұрын
Does the intercooler pipe have a plug...so it can be plugged till u get the cpi
@stinger_gt2192 жыл бұрын
Yes, it’s covered
@twinturboaddict Жыл бұрын
If I install a cpi kit can I still run regular fuel or do I always have to be mixed from that point on?
@stinger_gt219 Жыл бұрын
You can run regular gas bro
@stinger_gt219 Жыл бұрын
It’s also recommended to run 93 to clean out the system after running Emix for a while
@twinturboaddict Жыл бұрын
@@stinger_gt219 sweet bro. I appreciate your quick response.
@jorgearroyo7003 Жыл бұрын
I have a few questions 1- did you improve times at 1/4? 2-how that injector get activated to push extra fuel? 3- does BMS give support for installation?
@fabianmichel21852 ай бұрын
Is it possible to run full E85 with a CPI only? Even if to performance improvement?
@awdgt2stinger2702 жыл бұрын
What kind of fuse box extension thing is that sitting on top of your fuse box?
@stinger_gt2192 жыл бұрын
It’s one I bought of amazon just so I can plug anything else like my underglows, lit kit ex.
@brian32552 жыл бұрын
How did u disconnect the stock fuel lines? Any fuel spew out when those got disconnected?
@stinger_gt2192 жыл бұрын
There’s a tool you need to get for that. I Show it on my flex fuel install. And if you let the car sit over night. The fuel will lose pressure and won’t be to hot and you won’t get any or very little
@hasanfadhil64042 жыл бұрын
To the moon
@tetrocloudsgaming6201 Жыл бұрын
Does injection location matter?
@stinger_gt219 Жыл бұрын
As long as it’s on the charge pipe
@purrly85782 жыл бұрын
If you don’t run above E30 is there any advantage to a CPI kit?
@stinger_gt2192 жыл бұрын
Well if you keep it on, I’m guessing it’s still going to push more fuel through the charge pipe.
@sajadalsaady20062 жыл бұрын
Bro, I don't have a FSB controller can I use the CPI kit without it?
@stinger_gt2192 жыл бұрын
Unfortunately it won’t work without a controller bro. They have different options for controllers
@OGVendettaRacing Жыл бұрын
Bruh, did toy ever find a regular slot in the fuse box to use for the fsb power, the pictures on the install guides are crap, pretty sure my injectors not cycling
@matthewwarner31302 жыл бұрын
Any know what fuse location is best
@stinger_gt2192 жыл бұрын
I’m sure a sensor would work I just wasnt able to get a hold of an adapter to plug It into the fuse box
@matthewwarner31302 жыл бұрын
@@stinger_gt219 i used the coils
@stinger_gt2192 жыл бұрын
@@matthewwarner3130 that one turn on and off with the car?
@amaurysalmeron2 жыл бұрын
Have you had issues connecting to the JB4 after installing the cpi and running too high of an ethanol percentage?
@stinger_gt2192 жыл бұрын
Only get a check engine but I spoke to BMS and they said it’s normal since I don’t have an ECU tune yet
@amaurysalmeron2 жыл бұрын
@@stinger_gt219 what’s the highest e-85 percentage you have ran with this ? So far I have done e52
@stinger_gt2192 жыл бұрын
@@amaurysalmeron I think 54 is the highest
@timmy_-gh8bi2 жыл бұрын
@@stinger_gt219 hey brother is there a point in having the jb4 with an ecu tune or the main purpose is for jb4 to control what’s going on and the ecu tune is just unlocking more potential? So I will end up getting a CEL when I do install my cpi? Or just when you run more then e30-e40
@Get_StungGaming2 жыл бұрын
Track on friday bro! All 3 cars need to hit 11s
@stinger_gt2192 жыл бұрын
Yes sirrrrrrr
@xxbasketballxx1232 жыл бұрын
Do you know the hp gains with this?
@stinger_gt2192 жыл бұрын
Tuned should get you 25-35 easy
@joses53882 жыл бұрын
I CANNOT FOR THE LIFE OF ME TAKE APART THE ADAPTER ITS SO TIGHT. HOW DID YOU DO IT. ( where the fuel line connects)
@stinger_gt2192 жыл бұрын
I used to wrenches 🔧
@joses53882 жыл бұрын
Yeah I didn’t want to but it’s so tight and now I’m struggling to get it back in lol
@stinger_gt2192 жыл бұрын
@@joses5388 you have to do the same process to put it back
@joses53882 жыл бұрын
@@stinger_gt219 thank you captain obvious. I was just hoping you had some trick. I can’t get it to click back on
@stinger_gt2192 жыл бұрын
@@joses5388 try pushing in and twisting at the same time. If not, message me on Instagram and I can FaceTime you so we can figure it out together
@robbb89082 жыл бұрын
Looking at cpi...what mixture u running now for e85? Great video
@stinger_gt2192 жыл бұрын
E50 for now
@yankrzzz-apg49035 ай бұрын
currently installing the cpi kit , anyone know where to plug these fuses in ? i had them plugged in but no power, im thinking a bad ground or bad fuse location
@saadkamalsk26 күн бұрын
Same did you find the solution? I just connected everything but my injector dont make that sound
@oceanlifestyle23712 жыл бұрын
Can u run both cpi and wmi same time??
@highlyactivecannabis33442 жыл бұрын
No need to cpi can push extra gas rt from your gas tank
@mowglig9382 Жыл бұрын
I fell victim to lifestyle creep. Now I can’t afford my Stinger so I’m gonna be homeless I’d rather give up my apartment then this damn car. I’ll be living that stinger life haha