Crane Boom Broken Due to Overweight / Let's See how to Repair it.

[@Masonicx]

US pipeline welders are physically sobbing looking at that guy's welds. LoL

[@СергейМистрюков-е4з]

Шпакля добавляет ещё тонн пять к грузоподъёмности крана. А если всю стрелу зашпаклевать, то на двадцать тонн больше станет поднимать. 😂

[@kolsen6330]

As a former crane repair guy, i have several comments. Heating a boom section to straighten a wrinkle makes a soft area in the boom. Where did they get the new plate for the repair? Is it alloy steel like original construction or just a chunk of mild steel? Did they have a sample of the old boom material tested to see what is or contact the factory to find this out? I wouldnt load test or certify this repair and I have done this repair several times. Trigger welding isnt welding. No attempt to check overall straightness with a string line or laser. And finally, if you have to use bondo to make it look good, you shouldnt have even tried to do the job.

[@COM70]

Poor guys doing it have no glasses, ear protectors, respirators, or closed toe safety shoes either. I’m guessing safety is a bit of an illusion in that shop.

[@Colenuiogyrez]

О мой друг, посмотрите на условия в каких выполняются эти работы, в тапочках и халате, о какой сертификации можно говорить ?

[@ХонорСамсуе]

Вы правы , я бы побоялся на такой стреле работать , всё таки с людьми работать, а на кону человеческая жизнь

[@daveevans1236]

Iam sure the nice paint job will make it super strong😅😂😊

[@sahrulhamdani3874]

the welding results are not convincing 😩😩😩  

[@Jooligan1]

Amazing job. I hope they got well payed for this.

[@mikemilburn7823]

I was a bit concerned about the bubblegum weld, once I saw the body fill going over it all is good as that will strengthen it up. I assume it's guaranteed until the first lift or 'till it breaks whichever comes first? (If it lasts long enough to get it reassembled). Nice paint job tho.

[@sheungng1126]

It was a hard work to weld inside this boom which barely enough for a slim welder 😅 Great job ！

[@lliambunter]

Wouldn't like to be under any lift that crane was doing

[@ToddBishop-m2n]

Not to discount this video at all...but I think a prequel of this crane when it broke would be at least as horrifying in terms of safety as this. Actual build quality may be a toss up in terms of end user experience. What's another time bomb gonna do in a room full of time bombs.

[@Givoy]

Первое видео где варят полуавтоматом так и до лазера недалеко.Молодцы ,успехов.

[@user-6x6truck]

И режут болгаркой, а не бензорезом

[@ramilramil2944]

Мягкий меттал поставили, там должно быть легированная сталь. При нагрузке стрела сломается именно на закладке из сырой стали, это может привести к серьезным последствиям...

[@antongyrt4814]

Как они работают без очков? Я работаю всегда в очках и все равно залетает под очки. У меня в больнице мед карточка вся исписана; Инародное тело в глазу, инородное телов глазу...

[@СашаСаша-п9у6я]

@antongyrt4814"Инародное тело в глазу, инородное телов глазу.."Сначала не понял...потом поржал!🤣Спасибо!Первый раз вижу,что бы ТАК!"ошибались".

[@antongyrt4814]

@@СашаСаша-п9у6я Это все Т9 чудит)

[@СемСеменыч-б2и]

Скоро у тебя будет инородное тело в тазу если долги не отдаш

[@user-6x6truck]

Всю жизнь без очков и защиты на болгарке.. Просто пилите от себя и наклон диска делайте

[@thepubliceye]

Are they using flux core wire?

[@Th3R4k]

First time i saw safety glasses and angle grinder quard in in this type of video!

[@andiv8942]

Und das Gebruzzel soll halten? Ich habe so meine Zweifel, auf zum nächsten Unfall!

[@hermanschijf21]

Hallo from holland,hard working people.

[@utube1818]

Hard working people does not influence the durability of a repair.

[@michaelguinn5736]

Unbelievable! doing all that cutting & grinding with no safety glasses!!

[@steve_weinrich]

They switched the piece at 18:50!

[@mikemilburn7823]

I see what you mean, dunno they switched it or just out of sequence.

[@steve_weinrich]

@@mikemilburn7823 Notice the alignment tabs on each end are gone and the temporary lifting points are down to one.

[@josedossantossilva5091]

Bravo les gars nous avec beaucoup plus nous on fait beaucoup moins

[@diestrunzenstrunz4103]

Den richtigen Halt bekommt die Sache erst durch die Spachtelmasse !

[@sonicigroman4673]

Мне больше всего понравилось, как они на ручном листогибе форму сделали. В остальном шляпа 😅

[@gregmorley1997]

Put it back together and sell it quick before it snaps probably the first time it's loaded up

[@thomasjones613]

None of what they did to make that repair would be legal in the US. You would have to replace that entire section of boom with either new or used. I like the rubber glove the "welder" is wearing on his left hand.

[@Tc_Uni]

Que valentía tienen de utilizar la amoladora sin la protección del cubre-disco.

[@АндрейИванов-м5т]

Где проход корня и последующая сварка??? Это же не мебель варить

[@KING-FU]

For those being critical of the welding / repairs… it’s just a crane boom. Nothing to see here. 🤣

[@tibortakacs5722]

100%, hogy nagy terhelés alatt eltörik.

[@thepubliceye]

It did new so it will again if overloaded.

[@codures]

Less than that. Bent metal has weak spots and micro cracks, that boom is totaled. It might hold 70% of what it was but above 80% it's a miracle.

[@МихалПотапыч-в2щ]

Еще походит! 👍

[@ДуйсенказыКайырман]

👍👍

[@deanwitherow9789]

new safe work load 1 kg per mtr off boom. should have been scrap or dog houses, i hope this isn't been sold of over seas ?

[@robertmoody2221]

They had to use bondo to clean up the welds . Hope I never have to use this machine

[@honda2555]

Was für kleine Löcher für die Belüftung reichen , aber das ist von Land zu Land verschieden 😮

[@felixacuna4139]

Sin zapatos de seguridad, sin guantes de seguridad, sin protector de oídos, sin gafas de seguridad, esta empresa es de comienzo del siglo 1800

[@Tangaroa775]

What about the repair of the crane boom it should be junked not repaired😂

[@Wolli_]

bester Arbeitsschutz aller Zeiten 🤓🤦‍♂

[@w.o.o.d.y]

How do we know it's straight ? "we use string". How do we know it's not twisted ? "we used same string". How do we know it's strong to original spec ? "we used car body filler" Will this kill someone if it fails ?? "we can make coffin from off-cuts" omg.

[@stoffes]

u dont repair a crane part u do a new , the steel can be broken beyond eye sight..... but i guess look how many 1000+ crane and lifting accindents in some parts in asia, pakistan,india

[@thepubliceye]

I hate it when that happens.

[@pdmpdm999]

OMG. No safety equipment or guards used, exposed wires coming out of the grinder and also note the inline switch because the factory switch must be faulty. Yep NEVER EVER going that Crain.

[@jasonburke3064]

That welder is to hot. That’s what makes the splatter like that. Union sheet metal workers #24.

[@PILOTabcdce]

шпатлевка -наше все!

[@SPUDHOME]

Don’t trust any repairman with a clean shop floor.

[@patrickradcliffe3837]

Yeah, but no.

[@Denis.11]

Главное красиво покрасить.... что за сталь при..с,рали, зачем, как это будет работать.... па...ху...йу....

[@Kill2twins]

Очки надаааааа