CRANK Position Sensor Test - failing CKp sensor - CKp test

How to do a CRANK position sensor test in 15 seconds❗ Do this CKp test INSIDE the car. Know immediately if you have a failing CKp sensor, which often has NO EML & NO code.
🎥 How to clean a MAP sensor, P0106: • Dirty MAP Sensor Probl...
💚 Support the channel here: www.buymeacoffee.com/CycloneCyd ☕
💡 Subscribe and hit that bell 🔔 to learn more about looking after your car.
Is stalling or non-start caused by a crank sensor problem❓ Especially a bad crankshaft position sensor but no code issue. No special skills required. Easy DIY
If you are lucky enough to have the EML on (engine management light) then the code (DTC) may well be P033x. A failing crank sensor often shows NO code though.
Something I have noticed from a variety of forums, is that diagnosis of a CKp issue can sometimes be very "hit and miss". Garages often play "parts darts", replacing parts at YOUR expense until something solves the problem. This method I'm showing you can instantly tell you if you need to replace the CPk or "eliminate it from enquiries"
This test is for cars without a CAMshaft position sensor, ie a CRANKshaft sensor ONLY (most non Japanese petrol cars).
❗❗ This method cannot be used on cars with both CAMshaft and CRANKshaft sensors ❗❗
ALWAYS check wiring continuity and condition before replacing any electrical parts.
Don't forget to clear your EML codes once you have fixed any problem. I use Torque Pro app on Android. There is a choice of similar apps, but for the money they are hard to beat. Just using them once is cheaper than a garage doing it for you. You'll need one of these Bluetooth adapters
WW 🌍 bit.ly/OBD2_BT_Adapter (for phones with Bluetooth)
OR a wifi adapter:
WW 🌍 bit.ly/WiFi_OBD_Adapter (for Apple iPhones without Bluetooth)
Learn more about looking after your car:
🎥 How to replace a CV [constant velocity] joint boot with a split kit: • Universal CV Boot Repa...
🎥 Don’t let your fuel filter end up like this 100,000 mile old example:
• Why Should I Change My...
🎥 Battery & alternator care in this playlist: • Alternator and battery...
Everyone should have a tyre pressure gauge in their glovebox:
bit.ly/Tyre_press_guage
bit.ly/Pressure_Gauge_2
I personally prefer a stirrup pump to a foot pump (I use the same one for my bikes and cars)
bit.ly/Tyre_stirrup_pump
If you’d like to learn about the science and engineering of cars:
Bosch Automotive Handbook:
amzn.to/39va9xA
Are you trying to grow your own KZbin channel? I use TubeBuddy, try it out for FREE:
www.Tubebuddy.com/CycloneCyd
Gear I use in filming and production:
bit.ly/CC_Gear
My videos are edited with Filmora X - try it for free
bit.ly/Filmora_X_try4free
Thank you

[@CycloneCyd]

📽 How to clean a MAP sensor, P0106: kzbin.info/www/bejne/ppizdKWfpLBgbKM

[@jenridge7768]

This is a great video because you discuss the RPM at 0 during sensor fail. No one else out of 30 videos discusses this. Thanks.

[@CycloneCyd]

Hi Jennifer, thanks for watching and for interacting. Welcome aboard. Yes, it's part of my "back to basics" approach where I am trying to show that faults can be identified or narrowed down by testing and that garages using "parts darts" at customers expense are simply incompetent and ripping people off. Another good example is coil-over-plug units (I'll cover this later this year). Granted this test is not 100% foolproof but it does work for most cars most of the time. To be 100% foolproof you need a picoscope (plus laptop). At around £1000 picoscopes are simply beyond the capability of the vast majority of DIYers. You can see a picoscope in action here with Oz: kzbin.info/www/bejne/rZ7Sgqufpr6Labc Don't forget to share and if you have any suggestions for future videos add it to the comments here: kzbin.info/www/bejne/n5XOmqyXlJyHqpY

[@jameswakeland593]

Agreed! I haven't seen that info anywhere else yet! Ill be checking RPMs first thing in the morning!

[@akbaraliakbar8437]

Akbar

[@bonbont6912]

Yeas on point!! That wat I was thinking and I think my car is failing at crank sensor.

[@extrachannel7457]

My sensor is stuck!!!!! It's a hard reach and needs to be out!!! Any idea to get it out from Saab 9-3 owners? 🆘🤦‍♀️🤦‍♂️

[@evankemp9434]

I love this video. I have had issues with my car starting for 3 months and not a single mechanic has been able to figure out, no forum, youtube video, or article has been able to help me diagnose the issue properly. Your video is amazing! Very professional, clear, and direct really showing all the symptoms and how to test them. Thank you!

[@CycloneCyd]

Brilliant! Glad it helped. What car was this on?

[@evankemp9434]

@@CycloneCyd this was for an s197 mustang 3V

[@connor3288]

Did you resolve issue, what was wrong? Those 4.6 3v's have vvt right?

[@lloyd-qt1mg]

There's nothing like experience , coming to the rescue! Thank you for sharing your deep knowledge on automotive 'issues'.

[@CycloneCyd]

Training in Rover Group in my younger years when I was also driving and building rally cars was incredibly instructional. Whatever issue I came across, i could find someone in the company who could help me. It was a massive period of learning and I never stopped. Now I feel priviliged to be able to pass that learning on and earn a living from it.

[@BillSikes.]

Thanks mate, this is the best diagnosis video for a faulty CNKSS, on the whole of KZbin, simply and straight to the point.. Round of applause 👏👏👏

[@CycloneCyd]

Hi Strake750, WOW, high praise indeed 💚 thank you. I was actually inspired by most garages saying you can't test them, so they test by substitution (diagnosis by guesswork I call it). To test them properly in the early stages of failure you need a picoscope, which is out of the reach for a DIYer (around £1000 worth 💰). This method, of course, is free and easy and anyone can do it. If you want to see it being done with a picoscope, watch this video from @Oz Mechanics kzbin.info/www/bejne/rZ7Sgqufpr6Labc Welcome aboard. 🖖

[@BillSikes.]

@@CycloneCyd Ha ha, it's funny you should send that link, I was watching that one until he produced a large hammer, when I saw that, I immediately switched it of then come across you video, but thanks anyway and good day to you Sir

[@agoodone8091]

I have been looking up info on CSPS for weeks and this is the first time I heard anything about the tachometer not moving. Thank you so much for this video!!

[@CycloneCyd]

Did this help you out? Have you diagnosed the problem?

[@heytheredollfacex]

@@CycloneCyd This is so helpful!

[@vawtermj1065]

Watched several videos and nobody ever mentioned checking the tachometer as you’re cranking the motor .. thanks a bunch!

[@RarePartsRetailerFLA]

Very good. Your vídeo went directly on the right track. I've been watched hundreds and no one explained so well as yours

[@CycloneCyd]

Thanks for your comments, greatly appreciated.

[@bouncingsoul777]

Good video. Covered the symptoms well and got straight to the point

[@CycloneCyd]

Thanks, glad it helped.

[@garrydunkley1000]

Your the man ! Very informative and concise 👍👍👍

[@CountrySideways]

Amazing clear explanation with a simple test, I couldn’t ask for more! Thanks!!

[@CountrySideways]

I just got in a trouble on a highway with supposedly broken CPS in my Volvo V70 (2001) and fortunately got my friend to tow me home. I’ll check if it starts when cooled down. As I was trying to start the car by the road, it sounded almost like a broken ignition preventing system, somewhat like on this video.

[@CycloneCyd]

Keep an ey on the tacho when it won't start.

[@supersammy00]

Just helped me fix my Saab 9-3. I remember watching this video a while ago and just last week my car had an issue starting no tachometer for a minute tried again started but I stalled at a stop light. Swapped out the sensor and it started right up. Thanks for helping me keep my Saab running I’ve used other videos of yours in the past too. Keep up the great work.

[@CycloneCyd]

As long as people keep watching, I'll keep making. This is my living now, since JLR threw me under the covid bus (with 1000+ others). It'll never make me rich, but better than stacking shelves at Aldi, lol

[@FSaeed-sp8zz]

Very informative. Thanks

[@gernotskupin8472]

Vielen Dank für das Video! Mit Ihrer Hilfe könnte ich das Motor-Problem an meinem Hyundai i30 lösen. Ihre Fehlerbeschreibung ist perfekt. To make a long story short, thanks you.

[@OtamanSirko]

Thanks for your help!

[@ProSaiyanYer]

Great tip to remember! 👍🏼

[@user-po9sg3ks4p]

Thanks for the advice 👍

[@tharakadamsarademattanpiti4012]

thanks for the valuable information

[@Acer-ep4xg]

I learned something today. thanks

[@dariobrzovic9838]

thank you so much for the video

[@joaquinaguirre2976]

Thank you so much friend. I will keep it in mind. Appreciated a lot.

[@RussNo1]

Good info. Thank you.

[@sandroSwann]

Also explains how Japanese cars have Both a Camshaft & Crankshaft Sensor b/c you will get this question when purchasing a new sensor...The only 1 to clarify this of ALL the videos on KZbin. Cheers Mate ;)

[@Bayoustate2011]

Thank you for making this video! It was very helpful in my situation with my 09 Camry.

[@CycloneCyd]

Awesome. You're welcome!

[@gasciotti]

very important easy advice! Thank you! I have problems with my Fiat Stilo 1.9 D. Will try tomorrow

[@CycloneCyd]

Ah, the Fiat 1.9 diesel engine. Same engine is fitted to Saabs, Vauxhalls and more. I've got a horrible feeling that engine has a CAM sensor as well as a CRANK sensor, but I'm not certain. You will need to check your service manual. Please let us know what you find out and how you get on.

[@abhishekshivakumar4790]

Thank you buddy, right video for current issue of my car.

[@CycloneCyd]

Welcome aboard

[@louiediana2]

Thank You ! Excellent info! Great simple test. Much Appreciated!

[@CycloneCyd]

Thanks Louis, comments like yours make it all worthwhile

[@macmusica]

That looks to be good advice!

[@kevinsalinas9104]

Great job, precise and to the point even with examples. Suscribed 👍

[@CycloneCyd]

Thank you

[@fransjoubert4182]

Thank you very much! Excellent explanation, will try in the morning.

[@CycloneCyd]

Let us know how you get on

[@Digbite]

Thanks for sharing. Best diagnosis!

[@CycloneCyd]

Just a straight forward, back to basics approach 👍

[@easyyards3154]

Fantastic! As others have said, I've watched countless videos and none of them mentions this! Unfortunately "mechanics" these days seem to be more and more parts fitters, rather than diagnosing and fixing things!

[@CycloneCyd]

Yeah, 'computer says no' types. It's a lack of investment in training.

[@danisallit7722]

thank you .. you are the best in this description

[@CycloneCyd]

Thank you Dani, appreciated. Welcome aboard

[@mijharmonjim]

You are the best this presentation is amazing greeeeat!!! Definitely subscribing to this channel

[@CycloneCyd]

Wow, thank you! Welcome aboard. What car do you have and where in the world are you?

[@davidmyers5417]

helpful thank you for posting. from Hawaii USA

[@CycloneCyd]

mahalo iā ʻoe no ke nānā ʻana i kaʻu wikiō a hoʻokipa maila ma luna o

[@tomvarcoe3100]

Nice clear information. You nailed it 👏

[@CycloneCyd]

Glad you liked it

[@MD-pt2mw]

SUBBED! THANKYOU

[@scotia3d263]

much appreciated, good detail.

[@CycloneCyd]

Thanks

[@giloquendo]

Hi cyclone omg you saved me a ton of money the negative cable has 2 cable one that goes attached to the engine and the one that goes to the body of the car came loose I just cleaned it and tightened it and problem solved no more cutting off and no more flickering again thank you so much.

[@CycloneCyd]

Brilliant! Thanks for letting us know. Maybe seal up the connection with a 2 thick layers of brushed on enamel paint.

[@Sg-bg7xp]

Very well explained. Thank you

[@CycloneCyd]

Thanks, Zero. Sometimes when you know what you're on about yourself, it can be hard to get it out in a way others can understand too, so it's nice to know I'm succeeding. Welcome aboard 🖖

[@hardrockcafe4436]

Very nice video tutorial,now I have an idea how to diagnose bad crankshaft position sensor.

[@CycloneCyd]

Cool, thanks. Is yours giving you trouble? What car & engine?

[@arowanachen]

Thank you for showing this. It happened to me long time ago, took me a lot of time to figured it out .

[@CycloneCyd]

Yes. The lack of codes confuses even mechanics

[@denospyridon3126]

shuo chen - I post the same thing without even seeing your post first. Men that was annoying that the check engine light doesn’t tell u that. Would save a hole lot of grief.

[@liberal90]

shuo chen 我也遇到热车之后 行驶中熄火的问题 怀疑是crankshaft sensor。但是没有故障码。

[@murfman53]

Nice one Cyclone Cyd.

[@CycloneCyd]

Thank you Murf 👍

[@madsardthung6892]

Million thx 4 sharing this video, hoping you will share more on the other issues. GBU pal🤗

[@CycloneCyd]

you're welcome. There'll be more. Anything in particular you need?

[@itsbeenmacgyvered5916]

I just went out to crank our 2005 Buick Rainier, and had zero RPM's so tomorrow I will put a new crankshaft sensor on, and hopefully it will start & run as it should. Thanks!

[@CycloneCyd]

How did you get on?

[@overlanding4less419]

Really helpful, thank you!

[@CycloneCyd]

You're welcome!

[@ttautogarages]

Wow thanks never know this.

[@djnaresh1]

very helpful

[@ColtAshley]

Yes! That was my problem! Thanks you

[@CycloneCyd]

👍👍

[@rukus100821]

Thanks cyd that helped me understand that it's not the crank or cam sensor but with the smell I'm getting after starting that a o2 sensor has failed

[@CycloneCyd]

Better than 'parts darts' eh?

[@JonathanO711]

You are a cool guy

[@markadolphus5094]

Short and sweet but most of all informative! Thank you! I just discovered I just unplug thus and put on a new one so I best get started and I will ask my mechanic why he didn't know this when I described these symptoms exactly and only? *second mention the tachometer reading!! Der... why has nobody ever mentioned this, is it too obvious? NOT

[@CycloneCyd]

Yeah, I think it is. It's just way too simple for most people. Yes, cars are more complex than they used to be, but people somehow imagine that failures also have to be complex. Not at all, sometimes you just need to get back to BASICS - it's nearly always some simple component failure. It's the same with coil-over-plug units. Mechanics will tell you they can't be tested other than by substitution (aka 'parts darts'). Again not true. I'm actually in the process of filming a video on how to test COP units!! With a £10 tool too. Watch out for it. Welcome aboard

[@2917mushtak]

thank you. very honest explanation.

[@CycloneCyd]

So nice of you

[@Justin-ip1xu]

Very informative, cheers

[@CycloneCyd]

Thank you. Did it help solve a problem?

[@patricklewis1728]

Thank you for the message

[@CycloneCyd]

Thanks for watching. Welcome aboard

[@MD-pt2mw]

SUBBED!@!!!. THANKS BUD

[@donaldbarron7916]

Awesome show !!

[@CycloneCyd]

Glad you enjoyed it!

[@wildkariba8838]

Thank you very much

[@CycloneCyd]

You are welcome.

[@raulbotero982]

Excelente video.

[@LuvBlues64]

Thanks for this, my Clio randomly won't start the first time, ill check the tachometer next time it happens.

[@sanitei8767]

love your videos on Saab 9-3 keep it up .

[@CycloneCyd]

I will. Thanks.

[@RarePartsRetailerFLA]

Great sharing.

[@CycloneCyd]

Thank you! Cheers!

[@juleswilson5155]

Great explanation

[@CycloneCyd]

Glad you think so! It's about getting back to basics, something mechanics don't seem to be taught these days

[@marteenmbiri8139]

Very useful video

[@CycloneCyd]

Glad you think so! Did it help you solve your problem?

[@mbrunocondello]

Top information!!

[@CycloneCyd]

Thank you. Welcome aboard

[@randolphsloan2263]

thanks so much

[@CycloneCyd]

Welcome aboard

[@prashanthsreedharan9536]

kool video.

[@CycloneCyd]

Thank you Prashanth. Did it get you out of a pickle?

[@bvondobvondo2647]

Thanks lot

[@volt8684]

Gem to keep in my head thanks

[@CycloneCyd]

👍👍

[@JohnGKing-lg4yi]

This video was a Very big help to me this turned out to be my problem

[@CycloneCyd]

Excellent. What car was this?

[@JohnGKing-lg4yi]

2006 Kia Sorento

[@Boblee1975]

Good info ! Thank's =)

[@CycloneCyd]

Thanks Rob. And thanks for subscribing.

[@Keychaincustoms._43]

Hello sir i just wanna say thank you for your help i shouldve took ur word seriously i had a misfire with no cides and come to find out 2 coils were garbage

[@CycloneCyd]

some you win, some you lose. As long as you learn something from the experience.

[@MildlyCurious]

Very good tip on the tachometer.

[@CycloneCyd]

Glad you liked it

[@msred1281]

Thanks

[@AndySantiago-yd5lh]

I hope this is my problem, already order the part !!! Thanks brother for the info !!!

[@automotiveperformancemobil4030]

Update?

[@AndySantiago-yd5lh]

Automotive Performance Mobile Mechanics after I change the sensor my car still stalling, I look more deep into videos and forums and looks like is the fuel pump or the fuel pump control unit I drive a GTI MK6 2014

[@ThisIsTheRealMe2]

Thanks for the tips, very helpful!!

[@CycloneCyd]

Welcome aboard Mike

[@ThisIsTheRealMe2]

@@CycloneCyd Thank you, I had just replaced the fuel pump about 3 weeks ago. I hear the pump prime when I turn the key, but as you stated the tachometer does not register during crank. I'll give it a go, replace the sensor and see what happens. Thanks!!

[@CycloneCyd]

@@ThisIsTheRealMe2 don't cheap out. Bosch all the way

[@nealharrison1141]

thank you

[@CycloneCyd]

You're welcome, thanks Neal

[@bayramilhan30]

Thank you very much for the information you have given ,I am having the same problem, thanks again..

[@CycloneCyd]

You are welcome. Did it help you trace the problem? And what car?

[@bayramilhan30]

Cyclone Cyd Hello, my car is 1977 ford taurus lx 3000 cc 201 hp, I am waiting for the spare part , nearly 100 percent we have had the same symptoms that you describe when the crank- sensor is not working properly, I will inform you about the result, thanks again for your valuable video.

[@kelwincartagena9928]

Thank you so much

[@CycloneCyd]

You're most welcome

[@tyansury4320]

Thx sir, your explain is very good. I'm subscribe now from indonesia

[@CycloneCyd]

Awesome, thank you!

[@mickdanvers1530]

good videoooooooooo

[@flfun2no]

This seems to be the problem I'm having in my 05 Jaguar xtype. Bummer I just paid the mechanic $350 to fix it. I like your presentation. SUBSCRIBED

[@CycloneCyd]

Hi there Frank. Thanks for watching and especially for subscribing and interacting. Yes, "a lot" (most, IMO) of garages like to maintain an "air of mystique" around certain components like crank sensors, coil over plug units and ABS sensors, often claiming that they can't be tested and that substitution is the only way forward (and anyway, the computer says it's faulty - which is not what codes mean at all). This is great for them as you rightly point out since they are being paid by the customer, often at inflated rates which the customer is in no position to challenge (thanks to that air of mystique). Good quality CPk units from the likes of Bosch are around £50 to £100 typically and changing them should take way less than an hour with the right tools and access.. We've all been in your position, been overcharged for something relatively easy. Don't let it get to you, learn from it and move on, but be better prepared next time!! Have a look at my videos about the Polo ABS light! You'll see similar experiences in the comments. Rant over, I'll get off my soapbox now!! Welcome aboard.

[@bobbyborg]

Great videos. Good personality. Clear explanations. Good work Cyd! PS: How do you define "best of" videos? Curious!

[@CycloneCyd]

Thanks Bobby, I've replied privately.

[@papandiawarndiaye9255]

Thank you teacher

[@CycloneCyd]

Welcome

[@One-Nas]

Great advice well said sir i have a spare car Toyota Yaris I’ve been searching months now 😀 what’s wrong I thought it was fuel filter but after Seeing this video I can now check and replace the crankshaft sensor Thanks

[@CycloneCyd]

Did this fix it?

[@markohara4769]

Brilliant video, looking at buying a saab 9-3 areo ttid. Owner says it cuts out whether its cold or at temperature, this sounds like it could be the issue.

[@JH-bh5lm]

Excellent thanks

[@CycloneCyd]

Welcome.

[@mdbadalmiah6808]

Thank you sir

[@CycloneCyd]

Welcome aboard

[@francismwaniki1135]

thanks information appreciated

[@CycloneCyd]

Welcome

[@doc2553]

A simple yet brilliant solution and answer to my problem of a 98 Chevy that wouldn't start. , My question was simply "Will The Tach Move If The Crank Position Sensor Has Failed?" Thank you Very Much !!!!!

[@CycloneCyd]

A back to basics approach. Something that seems to be missing these days

[@mcdonaldgc3020]

Legend

[@winstonleighton1358]

Thanks much .

[@CycloneCyd]

welcome

[@timklein3962]

Great video; gotta love the Brits; thanks !!

[@CycloneCyd]

Welcome aboard. Appreciate the compliment.

[@nicosteyl3709]

This guy knows his shit. Thanks for the video

[@CycloneCyd]

Thanks. It's not a guaranteed 100% test for all cars (especially diesels), but works for most Euro and US petrols.

[@jashimuddin660]

Nice experience

[@CycloneCyd]

Thanks

[@RicoC]

thank you very much!!! this I think will solve the problem with my Nissan Sentra GT180. 😊😊😊

[@CycloneCyd]

How did you get on? Was this the problem?

[@RicoC]

@@CycloneCyd I ordered one for my Nissan sentra GT180, yes it was the problem. thank you! 😊

[@CycloneCyd]

@@RicoC 🤘🤘

[@lloyd-qt1mg]

Hi Cyclone, I experienced the exact stall problem you mentioned, while driving a 2004 Peugeot 206cc. Did a continuity test using my DVOM between Bat neg & the CKSPS connector ( 2 pin), no sound! (Broken wire in all probability .... now, how to find the break , OR, 'back probe' the connector and bypass an earth to the engine, chassis or Bat neg to see if it'll run?

[@palvaani]

Exactly whats been happening with my vito, had gearbox reconditioned it must be then they damaged crankshaft sensor replaced without me knowing. So had problems, stalling while driving along, would start after a while or sometimes straight away. Headache. They had replaced with after market one, which was giving the problem. Mechanic told me things like you need original parts, you can get away with brake pads or new lights, but electric parts dhould use genuine

[@mcdonaldg2908]

I used this technique you showed here .... . and helped me realize one thing i forgot to plug the sensor .... Back on you should do the re learned for the crankshaft....

[@CycloneCyd]

What model of car do you have that the sensor needs re-learning?

[@gw2031]

Hi techies ,can you help. My 2009 vauxhall vivaro has a delay in starting, slight engine vibration and intermittent P0201 ( cylinder 1 open ) error above 3k revs. ( stop engine light )Garage checked wiring, charged me £450 for new injector still the same.have read crankshaft sensor can do this ?