Culligan Water Filter Review

[@jimmarandola5096]

Culligan Tech support recommends turning the top handle back and forth TEN to FIFTEEN times before installing the unit. That info used to be on their web-site, but the tech from Culligan International said that it has been removed for some reason. I installed mine in the Spring of 2021 WITHOUT doing this. In October, I could not turn the knob. (I never touched it before, as I never bypassed the unit.) It was difficult, but with some elbow grease and the wrench, I was able to get it to move, and I turned it back and forth the recommended 15 times. Works smoothly now. Also.....NEVER press the red button when the unit is under full pressure from the pipeline. Always shut the water off first. If you don't, water will get into the mechanism, and it will leak for a while. IF the unit leaks after installation and the O-Ring is intact and in place. Remove the housing and the filter and, with a long Phillips screwdriver, slightly tighten the screw that is inside the cap, just under the red pressure release button. Great video. Thanks. I hope my additional input is helpful.

[@ariesmusicangel]

I cannot get mine shut off!

[@senbertrand]

How much force did you need? Mine will not move either, and it’s starts to make cracking/popping noise and I do not want to break it.

[@stevemenegaz9824]

My top handle was stuck when I got it. I used a 18" pipe wrench to move the top handle before I installed it. Slow gentle force. It made a divot in the handle, but the handle can now be hand turned by hand. The supplied tool is a joke.

[@senbertrand]

@@stevemenegaz9824 I found I needed turn the water off, to bleed pressure off, then it will turn. It’s annoying, but it’s better than dirty water.

[@MrsGreycious]

Thanks for this vid. Home owner told us the water bypass wasn't needed before taking it off...but yeah, glad I followed your info here and shut all the water down, 1000 times easier.

[@mikeneff6057]

Thanks for the review. I bought 4 of these and made a diy step down system going 50 micron, 20, 5, 1 to a uv. They work great. The visibility is nice. However, it can be deceptive. A 50 or 20 micron filter will look much dirtier than a 1 or a 5 and the 1 or 5 could be plugged up and require a change. I used pex and shark bites. Put a shutoff valve before and after your filtration system. Throw a carbon filter in the mix if you need to clean up the taste.

[@fastrat37]

I just ordered one of these from Home Depot. Thanks for the great review! I'll try to update after installation and see what I can filter out of our water supply here in Castle Rock CO They just installed a new system to re-use the waste water and put it back into the system due to the over-crowding here in the past 20 years!

[@stevemenegaz9824]

I installed this filter at my water well to remove sand Much larger than old unit. I turned to top knob 40 times with wrench and recognized that knog was screwed up so I pipied it so I never will use the knob. My layout was 21"x21"x21". but I could have made it smaller to fit inside std plastic storage container. During warm months, I keep a heavy contractor garbage bag over the piping to prevent algae growth in the filter. The downstream pressure guage pokes out via a small tear. During cold moths, I insulate wrap all the piping and use loose insulation wrap to protect the filter and fill up up the second bag. I used vegetable oil to lube O ring as food grade silicone oil can only be bought online for $$$. My piping is all 1" PVC My piping is union, tee with3/4 hose bibb to blow sand out of tank,pvc isolation valve, FILTER , pvc isolation valve, tee with 3/4" connection for pressure gauage and finally union. The filter is mounted on a 4x4 that is about 3 feet in the ground. I use Tru blu for the pipe threads on the filter and on the hose bib and pressure guage connections. I used Otey primer and high performance cement and allowed 12 hr setting time, Very careful about gluing, so check video before starting. Blew well clear of sand via hose bibb before running water into filter. Not a single drip. RUns perfectly.

[@suehammond9548]

Just installed this filter with a water boss 900 water softener and OMG can’t believe what a difference. It’s like night and day. Our water was just like Rocket Scientists water. We had to spray iron out which works like a dream in our bathtub, toilet and sinks all the time. The water pressure went down just a little but you can hardly notice it the trade off was well worth it. Extremely pleased and the best money I ever spent. Thank you for your video it really helped me pick out the right system.

[@RocketScientist]

Thank YOU! Glad it works for you!

[@imfrompersia]

Hi Sue, I have a boss 900 water softener and I am planning to get one of these filters. How did you do it? Did you add this filter to your already installed boss 900 water softener or you replaced it entirely? Please let me know, I appreciate it in advance.

[@suehammond9548]

@@imfrompersia I put both in at the same time. I don’t think it will be that hard to add your filter. You will have to reroute your plumbing. Mine goes through the water filter then the water softener. Put some shut off valves if you just want to use the filter or just your water softener if one goes out. I am really happy with the system!!! I hope this helps.

[@BIBTAP]

Appreciate the review. Came to KZbin to see if this was the right filter setup for me (same issue as you mention at beginning of video) and you helped me make my choice. Also you mentioned Amazon- it’s $20 cheaper there than my local hardware store. I’ll be ordering today! But… I’ll spring for the SharkBites. Just laziness on my part. Thanks again!😊

[@ralphwhitaker8761]

Lol, you are a champ and so honest, I just bought it for the price, so ill install it this holiday coming when I'm off, and I'll come back to your channel for tips, thanks a lot

[@RocketScientist]

Hey thanks!!

[@downintheshed2449]

Love theses filters! Got 2 of them right before our softner and one after put softner. Ammmmmmmazing diffrence. I also use a carbon block filter on all three not the cheap stuff.

[@Sharonal110]

This is the exact comment I needed! Do you notice any difference in water pressure after installing the filters?

[@downintheshed2449]

@@Sharonal110 I see 2 psi change. I have a pressure guage before all my filters and then 1 guage after the 3 filters and a softner and I am only down 2 psi. Honestly you would never notice and could even turn up the pressure a bit if you have a pressure regulator

[@mar1video]

🤣 I’ve read that review on Amazon with water shooting 30’ out. It was hilarious ❗️ Thank you for your review ❗️ Great stuff - your video that is. So is the filter !

[@rogerwhiting9310]

After owning a few homes and many water filtration systems.... First...I would have a 10 micron or smaller filter. Lots of people use 1 micron...and thats ideal. AFTER the 10 micron filter I would have a SEPARATE charcoal filter for taste snd odor. My charcoal filter goes to the refrigerator and a separate spout....lasts a LONG time. Next...I have given up on built in diverters on top...they fail and leak. A nice ball valve before and after is all you need...the canister head has a button pressure release. Those are my tips for my himes now. There is a guy in here that cleans his 1 micron filter with oxalic acid ....and reuses the pleated filter 20 times! He even reuses the oxalic acid to soak them...4 times. He has a well...and obviously no charcoal combination filter. Lastly...plenty of plumbers make worse looking solder joints than you. They look good. My systems are all PEX A.

[@notmethanks816]

Maybe I can't see it in the video, but it is always a good idea to insert a bypass with three valves when installing a filter or appliance. This essentially looks like the following: --------------- valve --------------- | | | | valve valve | | | | ---------------Filter ---------------- This allows you to have a proper bypass where you can shutoff the vertical valves and open the horizontal valve. This allows the home to have water service while the filter or appliance is being repaired. In some areas of the country this is code. Just a suggestion for future projects. Hopefully you used swivel connectors at the inlet and outlet of the filter so that the filter housing is easy to remove and replace. It is hard to see from the video, but I could see someone using a plain MPT/Sweat fitting and then not having an easy way to replace the filter housing without cutting the copper.

[@RocketScientist]

I may not have shown it, but I do have a bypass system with ball valves exactly how you diagrammed it, which I must admit is rather impressive for a comment.

[@1973TJM]

Great video. I have purchased a whole house filter similar to this, and am awaiting help with installing it from my son (a contractor). I like that you did it yourself, and your comparison filter reviews. I wanted the larger GPM flow from the filter, so 1" works best for that. Also, the clear plastic cover allows you visual checks on how your filter is doing and is a great benefit.

[@RocketScientist]

Thanks! I love doing stuff myself. It can be intimidating if you've never done it. Best of luck!

[@Mathmusiciandlife]

I run a 5 micro, love the 1” lines no effect on water pressure. I used shark bite fittings for easy install with a ball valve on both sides

[@downintheshed2449]

We did have one that busted at the seam on top of the out side at 4 am! That was no fun but we got it fixed up with a new on under warranty it was only 28 days old. All good now.

[@VERDICT_SQUAD]

Here to show our support. We actually did a review of both a Brita and Pur water filter. We liked, watched and commented.

[@atxjax1]

Thank you so much for your review. I am planning on getting this exact same model installed in my new home. I plan to put a shutoff valve before the filter to make the filter change easier.

[@RocketScientist]

I have the same valve setup, highly recommend it! No need to fight with the bypass on the filter. It's real tight.

[@atxjax1]

@@RocketScientist Thanks for the input. I'm going to go with Sharkbite connections for mine because Im lazy and its fast.

[@kpforceone]

I used this same filter housing and it worked great for 5 years. It failed after the plastic molding seam on the top separated. I am not the only person that experienced a failure like this. Great video though.

[@errolsimmonds4133]

Great video man!!! Thanks for calling out some of these complainers who never read an instruction manual.🤣

[@jaimes1572]

Awesome review. Thank you for the info. Also pretty amusing while doing the daunting task of researching water filters.

[@thomassmith654]

Great review - thanks for sharing. Especially enjoyed the extra review comments!

[@RocketScientist]

Thank you! Yeah, I get a kick out of those ridiculously negative reviews.

[@michaelrobb9708]

Absolutely amazing video. I’ve learned a bunch

[@michaelrobb9708]

I probably knew lots of this, it’s just an enjoyable watch

[@haroldhprittjr7007]

We got city water and we had a smaller one and it did ok but two years ago we added this after the small one ! Now we use the small one for sediments then the big culligan to finish the job off . Now what we do is every three months change the small one and the the big one every 6 months it works out real well cause the new fridge got a water filter on it ! Yeah just like a good beer triple filtered water and ice . Who could ask for more ! Also for any one doing this he’s right on the rack to hold it and the pressure I installed ours as soon as thecwater line came in the house ! I put a ball valve then a tee off the tee first filter then second ! Down off the tee a valve and about 14 inches of pipe turn out and a hose bib so if I ever need a water hose there and the main part . SO YOU CAN LET THE PRESSURE OFF ! The bonus it’s at the lowest point in the house . That’s important if you have a leak and need to repair it remember the first valve shut it then turn hose bib on and all the pipes upstairs will drain out ! Then I can also use the hose bib to clean out my filter case ! It also leaves you between the valve off the tee to the hose bib to add another tee run a pipe for a hose out side un filtered of course but washing mud of or mixing concrete don’t need filtered ! Unless you cleaning the BMW or Mercedes’. We haven’t gotten that hi up yet so the Toyotas and chevys will be ok with unfiltered water ! And the rack is a must I made mine from bed rail and flat bar plumed all the filters and down spout in galvanized pipe copper between the filters and shark bite back to pvc ! Found little u bolt clamps to hold it on the parts that didn’t already have holes to bolt it and lag screws to the 6x6 header yeah if the house blows up GOD forbid you can look at the foundation and see it still bolted there full of water and everything else gone ! Great video great choice in filter live for it man ! Love how you educated those people on the common sense side of the street man some peoples kids but hay we all live and learn and do are best to help every one out cause that’s just what we do ! Great minds think a like stay safe man I done liked your video now let me go back and subscribe can’t wait man I just know your gonna have some more killer stuff happening I’ll keep a close eye on it !

[@davids.9583]

Thanks Rocket Scientist for the video! Getting ready to install the filter. The instructions say only use Teflon tape. With regards to leaks, I'm not too comfortable with that. Have most of you folks on this thread used only the tape as recommended? Did you have any leaks? The fittings I am using are brass and PVC.

[@RocketScientist]

Tape is just fine, no reason to overcomplicate it. Highly recommend Blue Monster. Its thicker and better quality than the cheap crap.

[@mercwithacat9938]

Good job always remember to pick up extra o rings and if your o ring gets stretched out toss it in the freezer for a little bit to shrink it back to size

[@MichiganPeatMoss]

Nov 2022: Just catching up. Buying this model. Thanks, great video.

[@worst141]

one thing. when u change the filter dont wrench tight the housing after. all you need is hand tight and greasing the o ring. wont leak. i almost couldnt get the one that was on there off from the previous owner.

[@jzizzles7799]

Thanks for the review. I was wondering how the F I was suppose to turn the knob. And the filter wrench was the answer. (I could have probably just read the damn manual).

[@steveritchie4926]

Thanks for the great review! I've been thinking of installing one of these, as I have a similar "rusty gunk" situation. Nice work!

[@RocketScientist]

thank you!

[@mariasoriano2505]

Thanks for this review! Also super funny.

[@AJDIYNetwork]

Great job! I’m going to install mine tomorrow.

[@kerrylittle3900]

OMG. The previous owner was drinking swamp water. Can I ask is that city water you are filtering or well water? Thanks. Very good video. Makes one think about their health.

[@RocketScientist]

Its well water.. Yeah, you just don't realize how much gross stuff is in your water until you can actually see it.

[@kerrylittle3900]

@@RocketScientist thanks for the reply. That’s scary. You would think well water would be the cleanest and safest water to drink.

[@shythawks9549]

hahahahaha love the reviews you showed. it never surprises me the things people say on amazon. i liked when you pulled into walmart on the go pro mount video and and the comments you were making were hilarious. maybe some more videos like that

[@chrisbonnet8588]

Thanks for the review going to put 2 of these in😁

[@drod5157]

Did you install it? you like it?

[@fubartotale3389]

I would have done a simple bypass loop with shut off valves Also a second filter with a finer mesh or a different media would give more flexibility.

[@urbanturbine]

i have a bypass and almost never makes a difference at the house because filter change out is so quick... and the unit has a bypass just in case you have to do something long.

[@bigsidable]

Man i love your video and your attitude. Your really good bro. Thank you for being real about shit. Best video ive watched yet. You just saved my day. Awesome.

[@jungleviper]

Just installed it. The 1 inch inlet that threads on is dripping maybe a teaspoon of water in a few hours. Very small drops. It seems like I can further tighten it but I'm worried about stripping it or cracking it.

[@RocketScientist]

If thats all, it probably only needs another 1/4 turn or so.. I cranked the crap outta mine.. its stronger than it seems. Only other option is take it back apart and redo it.

[@mar1video]

People are using Teflon tape and dope together to stop the leakage

[@Dhartmann85]

Thanks! Just ordered one with the better filters!

[@joebrothers3678]

supermodelrobot is

[@mavirek]

My townhouse has a covered front porch where PVC pipes hosted a water softener. We intend to place a screen to shade the Culligan WH filters from the Florida sun. We have a rough stucco exterior. Is it best to attach the Culligan WH filters to a board and then attach the board to the wall? I cannot imagine PVC fittings surviving the twisting and jostling involved in removing and replacing these canisters to change out filters without really securing these WH filters really steady to the wall.

[@babieangels]

Thank you for this video!

[@urbanturbine]

i guess it is not a big deal but you basically soldered the system with no flexibility. You will have to cut piping if you needed to remove or replace the filter body or rotate to adjust etc. But i guess that would be a very unusual situation. So, it should be ok. I plan to use unions on the inlet and outlet of the piping for that flexibility.

[@Cosmickitten2012]

So we are planning to have the whole home filtration system installed for a home with single shower and two sinks, starter home, the installer wants us to put in an over flow outlet like thingy for water to drip into? Lol don't ask me anyway, do the digging, to mainline, lay the concrete slab to sit the system on and buy a cover for it, it's going to be outside at the mainline. Total cost after "we do this work" is like 900$ +, where is your overflow or do you have one.

[@marys8232]

Thanks for all the tips you're awesome

[@RocketScientist]

Well thanks!

[@2u263]

Great Informative Review Video. Thanks. Wondering about your thoughts on WH - S200-C vs. WH-HD 200-C?

[@abdukhan55]

Very use full info but late I buy water softener system from clear water not doing well I spend 2000.00 I am new here in Guelph area For drinking water still buying water bottles in which area you are

[@dadlifegarage2292]

Just got one for sediment from my well. Gonna use pex and sharkbites. thx for the video.

[@Durkis0077]

Why does Culligans web site have no information on this filter or the smaller one? Where can I get more information about the filter and the cartridges ?

[@RocketScientist]

Check Amazon that's where I got mine.

[@ralphwhitaker8761]

I install the filter, the arrow is pointing on the direction of my well, i let the faucet open the whole time, after finish everything, i dont see no water flowing inside the filter, like you are showing, am i doing anything wrong? Thanks

[@dougbourdo2589]

Good review. I saw these recently at the local Farm & Fleet and was initially impressed. I especially like the 1" inlet/outlet as it tends to increase the continuation of flow.

[@RocketScientist]

Thank you! I continue to be impressed with this unit. I'm currently using a 5 micron filter with zero pressure loss after 2 months use.

[@MC-yb5le]

what exactly is the purpose of the blue handle on the top, why would you turn ?

[@DMac-gh7cy]

Great video and great information! I'll definitely a subscriber of your page.

[@RocketScientist]

Thanks so much!

[@mavirek]

Can this be used for a 2.5 bath townhome with 3/4" white PVC ~IF~ I find the right adapter to accommodate your 1" in/out ports? Is there a filter with some descaled property, like citrus or soliphos?

[@RO-Membrane]

the pleated cartridge is similar with our product

[@MC-yb5le]

I would choose a 5 micron filter, not a 25 micron.

[@platonkavvadias8541]

Do you shut off the well water pump before you change the filter?

[@RocketScientist]

No need to do that. Turn the bypass valve on top of the filter so its pointing toward you, then press the red button to release pressure.

[@qusai9014]

Very informative video! I have question about the filter Does it helps lowering the salinity with the AquaCrest Filter?

[@RocketScientist]

hmm. i don't know.. My water doesn't really taste salty to begin with, so I don't have any comparison.

[@auctionmusic]

I live in phoenix. What about installing in a hot garage?? as the intake pipe is right by the garage door

[@rd9008]

Great video. Is there any benefit of water softener in addition to using this filter?

[@RocketScientist]

For me there is because I have incredibly hard well water. If you're on a municipal water supply, you probably don't need one.

[@unclesnappy3555]

I have a city water supply that I never drink from. The rest of the lines of the home are subject to the chlorine, scale, and fluoride. I really have a problem with stinky wash machine, white scale build- up on the shower doors, and some black mildew funk that comes from the shower heads. I'm guessing the correct filter would be 99% of what I need to remove this contaminant correct? I have 3 full bathrooms but, only my wife and I live here so I don't have a huge water per gallon count. Would putting only 1 of these units in be enough to completely filter out my crud water? I know Flouride can't be removed with this and don't really care about that cause I'm not drinking it anyway. The dog drinks bottled water that most likely is filtered at their plants from tap water so hopefully no worries there. So would 2 of these in-line be a waste of investment? I have 70lbs of water pressure from the street and don't want to slow down the pressure or volume. Thanks for the video as well. I made a post on the Amazon site concerning this as well.

[@RocketScientist]

Sorry didn't get back to you sooner. Your comment somehow ended up in the spam filter which I almost never check. As far as filtering ability, it's mostly about which cartridge you use. I have since gone down to a 5 micron filter without issue. No noticeable drop in pressure. I've actually been considering adding a second one of these filters also. A friend did and he has it set up with a 50 mic first to catch the big stuff, and a 5 mic after that. Works great, and extends the life of the more expensive 5 mic filter. I'd say that's a worthy investment. Especially now that these filters are hovering around the $50 mark on Amazon. Worth a try for sure.

[@bigbuht]

That crud and white scale is hardness which these filters do nothing to remove,only a softner will remove hardness

[@frankletizia7835]

Is Aqua filter 25 Micron filter . THIS FILTER good use for well water ?

[@dclark66]

Great video. Just bought this filter largely because of your review. ONly question is what type of fitting goes into the 1" filter? is it male pipe thread?

[@RocketScientist]

David Caribou yes it takes a male 1" to 3/4", or whatever size your house pipe uses. Similar to one of these: m.grainger.com/mobile/product/5P031?cm_mmc=PPC:+Google+PLA&s_kwcid=AL!2966!3!166588641592!!!g!325537765342!&ef_id=Wu7TLQAAALoOKhAl:20180625235310:s

[@aronjohn84]

THX BRO AWESOME VIDEO

[@RocketScientist]

aron john sure thing pal!

[@clintoncline8604]

Great info,Thank you very much

[@mossfisher1806]

I wonder how that would do with city water

[@RVBadlands2015]

Is it a carbon filter. Does it take out calcium and salt. I have a septic so I won’t use salt/conditioner.

[@donaldthomason4588]

Would this solve hard water issues when washing a vehicle?

[@RocketScientist]

No, in fact, I just washed my vehicle with my softener on bypass and it left spots all over. Had to go back over the car with a towel and some glass cleaner.

[@jaycahow4667]

Have you had anymore issues with algae in your clear canister? I have read that while clear canisters are nice to look at they can promote algae growth and it is better to get opaque ones. I would have pressure gauges inline and would watch for a drop in pressure to know when to change them out.

[@RocketScientist]

No i havent. Just the one time. I also switched to a 5 mic filter. So far so good

[@alohajason]

Good video. Did you test the filtered water?

[@BCRSIX]

I must install this on an outside wall. What should I do to protect it from freezing in winter! Will build insulated box around it. Should I just shut the water off when it freezes (rare in Houston)? Any suggestions? Thanks!

[@RocketScientist]

Outside wall meaning outdoors? I wouldn't do that, but if you must, as long as its covered from exposure to normal weather. More importantly you can't just shut the water off. You have to be able to drain the pipes and this filter as well, or it'll just freeze anywya and split wide open. Its relatively cheap.. probably worth trying but don't be surprised if it doesn't last long.

[@NiGHTSaturn]

I noticed the whirlpool machine below, is this a water softener that has to be used as well?

[@RocketScientist]

That is indeed a water softener. The culligan filter is positioned before it just to keep most of the junk out.

[@randyjerrett3385]

I have one too, works great!!!!!

[@angelpadro6243]

My Wells outside can I put that outside with plastic pbc

[@petesopenworld4659]

Will that work getting rid of the smell from the water?

[@btaluy]

Great Video. Thanks

[@MiXReef75]

Great video

[@michaelhardy2735]

3 water filters UV light set up

[@jandnoc]

How often do you have to change the filters? I've heard someone say he changes his once a month. Is that true for you?

[@xeroforhire]

"it's only as messy as you make it" 😅 I love that part

[@kipbush5887]

They’re on sale now for $44

[@RocketScientist]

Oooh that's a steal!

[@jameslouis1627]

R u serious!

[@kipbush5887]

Jimmy Jam looks like price is up to $54 but still a decent price.

[@briangutierrez5635]

I bought that use house it a 1950 and I noticed that our little bit of rust on the toilet somebody told me to maintain a water heater I've been wanting to put a filter but does the water pressure drops a lot or is it barely notice or it doesn't do it at all

[@RocketScientist]

I have not noticed any drop in pressure, and I'm currently using a 5 micron filter. I used to have rusty toilets too, and that is all gone. It'll definitely keep most of the muck out of your water heater and appliances.

[@rickt2419]

Thanks for the review and time to make the video! Question: approximately how many turns to tighten the 1" fittings in to the filter without over tightening and if you used any teflon tape over the fitting thread? Thx!

[@RocketScientist]

Rick T Hi there! I didnt really count, but if i had to guess id say around 10 turns. I used teflon tape. I had to take it back apart once and tighten up cause of one little drip.

[@captncc9686]

I have lots of iron in my well water and I'm looking at alternate solutions. This Culligan unit goes on the water intake for the entire house? I'm guessing it would be placed before the water softener and would help it run better without all the iron? Thanks in advance.

[@RocketScientist]

Yes you are correct. It goes after the pressure tank but before the softener. Oh and by the way, I just tried the Fette Filter brand 5 micron with carbon and my water is as good as bottled water now. Thanks!

[@dale3guy]

Do you have a link for the 5 micron Fette filter?

[@michaelhardy8589]

4 water filters whole house system

[@Entertained45]

very cool and informative. here to support you best wishes bud.

[@marlonarchibald5069]

What type of cobblers did you use? I know the size 3/4 but when I bought some they don’t fit.

[@RocketScientist]

The filter has 1 inch inlet/outlet. So 1" to 3/4.

[@andrewgray4356]

It's hard to see, but it looked like you placed the filter ahead of your water softener.

[@RocketScientist]

Yes. Straight off the main coming in the house before it gets to anything else.

[@mrhutch2u]

did you install this filter before entering water softer or after?

[@carlosjaen4786]

I can’t close the valve it is stuck, please tell me what to do, thanks

[@RocketScientist]

Mine is tight too. Try using the large plastic wrench that came with it. The handle side is made to fit the blue valve on top.

[@laihuey]

cool video , plan to buy one soon, thanks

[@jatimmonsjr]

Great video. Did you install it on the street side of your water supply or did you install it between your water softener and the house plumbing?

[@urbanturbine]

Nevermind what he did.... You should install on street side.

[@Letsgo-og8st]

Hey I see you use a water softener. Am also on well water and already installed the culligan whole house water filter and the water water taste great! My ? is can i stop adding salt to my water softener since the filter is already doing such a great job? Thanks

[@RocketScientist]

I'd keep using the softener. The filter only filters. It doesn't change the water the way a softener does. I tried that and immediately noticed calcification buildup on all my faucets, coffee maker clogged up.. even with the filter. It was a pain. Yeah, keep using the softener.

[@creativej]

@@RocketScientist This answered the question I just left above. Thanks!

[@checkurselfb4ureck]

Set up video? I want to buy this but idk where to hook it up , my pipes are set up differently

[@RocketScientist]

Aside from being installed in a different place, what is set up different at your place?

[@checkurselfb4ureck]

@@RocketScientist I'm not sure if I would put it by the water heater or if I have to connect it to my well pump. I'm worried about space.

[@victorestrada2156]

Did you install before or after the water softener. Any ideas by installing it after the softener

[@RocketScientist]

its before the softener. The idea is to keep sediment and crap from building up in everything after the filter, which includes the softener. My water is very iron rich, so just trying not to kill my softener prematurely.

[@johnc3601]

Nice vid. Thanks ! Question: I see your water flow is from left to right. My pipes are the opposite. My feed (main) comes from the right side. Can the filter be rotated 180deg so the water flows from right to left ? In other words can I mount the mounting bracket & emblem/button on opposite sides ?

[@RocketScientist]

You can mount it however you need to as long as its upright, and I believe the button face and wall brackets are interchangeable, but the direction of flow is not reversible. Just make sure you don't mix up the in/out sides, and you're golden!

[@johnc3601]

@@RocketScientist Thank you for the detailed foolproof reply 👍

[@TriStarTravelers]

your reviews are great!

[@RocketScientist]

Tri-Star Travelers Aw thanks!

[@positivelyportugal]

Thanks!

[@mavirek]

Are you able to use non-Culligan filters with the unit?

[@RocketScientist]

any brand/type you want as long as its 10" x 4.5"

[@kpnitrl38]

Great review. Have you upgraded your filter again? To one that has a higher micron count?

[@RocketScientist]

I did change to a 5 micron with carbon. Works very well.

[@kpnitrl38]

@@RocketScientist Ah very good. I will follow your lead in that. One other question, do you think I would need two filters on a city water system?

[@RocketScientist]

@@kpnitrl38 eh, i guess it depends on the quality of the water to begin with. I'd start with one but pipe it in a way thats easy to add a 2nd one later if you choose to.

[@kpnitrl38]

@@RocketScientistOk. You have been happy tho with just one?

[@RocketScientist]

@@kpnitrl38 so far so good. I am on a well with a ton of iron particulate. I could probably use 2 but been doing just fine with 1.

[@johnserrano9689]

The real filters are actually still made in the United States! Unlike these Chinese here. Honestly well done review man and great for low budget. But want actually really good water from horrible water? Get the REAL one from U.S Water Systems. I have a deeper surface well that's not very good. I also have a family and a 1 year old that I will protect above and beyond no matter what. So I couldn't mess around with that style (but fine for city water supply) so I installed a dual 4 1/2"X 20" 222 seal unit with a 2" Rusco spin down filter ahead of it for fine sediment. Using the 5 micron Magna pleated with the Interceptor filter behind that my water is guaranteed against any bacteria, virus, heavy metal, VOC, basically any chemicals or metals you severely do not want! And my filters last a full YEAR! Plus after rainfall (water intrusion into the well water) I'd get surges of tannins which are actually very expensive and difficult to remove but us water systems Interceptor filter actually does the job, to my surprise honestly. As with anything worth it, ya get what you pay for period. Glad that little knock off unit works for you Man (I know how it sounds but honestly I'm not being sarcastic) but for a real permanent solution that once installed you'll be dumbfounded how you survived without it lol call U.S Water Systems....I straight up do not work for them know them or have any affiliation what so ever with them, they just are full on all pro, all American legit company that don't DCK around and their products are far far! Superior, work better last longer and cost about 5 bucks more. But these smaller companies are very hard for us to find without serious digging

[@bladamson1]

Do you reccomend mounting inside or outside the house to take advantage of the UV sunlight?

[@RocketScientist]

I wouldn't. No doubt constant exposure to outside weather would destroy it, but especially not if your location freezes in winter. That thing will split wide open along with your water pipes.

[@mar1video]

Inside only . The UV light will destroy the plastic housing on that filter.